对转压气机中机匣处理的非定常影响

郭彦超; 高丽敏; 茅晓晨; 王磊

doi:10.13224/j.cnki.jasp.20210508

对转压气机中机匣处理的非定常影响

doi: 10.13224/j.cnki.jasp.20210508

郭彦超^{1, 2,},
高丽敏^{1, 2,*, ,},
茅晓晨^{1, 2},
王磊^{1, 2}

1.
西北工业大学动力与能源学院，西安 710129
2.
西北工业大学翼型、叶栅空气动力学国家级重点实验室，西安 710129

基金项目: 国家科技重大专项（J2019-Ⅱ-0016-0037）；国家自然科学基金重大项目（51790512）；西北工业大学博士论文创新基金（CX2022044）

详细信息

作者简介:
郭彦超（1993-），男，博士生，研究领域为叶轮机械气动热力学。E-mail：guo_yc@mail.nwpu.edu.cn

通讯作者:
高丽敏（1973-），女，教授、博士生导师，博士，研究领域为叶轮机械气动热力学。E-mail：gaolm@nwpu.edu.cn

中图分类号: V231.3
计量
- 文章访问数: 236
- HTML浏览量: 43
- PDF量: 239
- 被引次数: 0
出版历程
- 收稿日期: 2021-09-12
- 网络出版日期: 2022-11-24

Unsteady effect on casing treatment in counter-rotating axial flow compressor

GUO Yanchao^{1, 2
,},
GAO Limin^{1, 2,*
, ,},
MAO Xiaochen^{1, 2},
WANG Lei^{1, 2}

1.
School of Power and Energy，Northwestern Polytechnical University，Xi’an 710129，China
2.
The National Key Laboratory of Aerodynamic Design and Research，Northwestern Polytechnical University，Xi’an 710129，China

摘要

摘要:
为探究不同形式的机匣处理扩稳机理和损失产生区别，以某两级对转压气机（CRAC）为研究对象，通过非定常数值模拟方法开展了自循环机匣处理（SRCT）和轴向槽机匣处理（ASCT）扩稳机理的研究。结果表明：SRCT和ASCT在近失速点均显著提高失速裕度和总压比，在峰值效率点附近增加效率损失；机匣处理通过作用于叶顶泄漏流和抑制压力势流减弱转子间动-动干涉效应；机匣处理槽内流场与转子相对位置相关，转子周期性的扫掠机匣处理槽增加了轴向槽内流动的非定常性，机匣处理槽内流动掺混是效率下降的主要原因。
- 对转压气机 /
- 自循环机匣处理 /
- 轴向槽机匣处理 /
- 非定常 /
- 扩稳机理
Abstract:
In order to reveal the difference between the stability enhancement mechanism and the loss of different forms of casing treatment, a two-stage counter-rotating axial flow compressor (CRAC) was taken as the research object, the stability enhancement mechanism of self-recirculating casing treatment (SRCT) and axial slot casing treatment (ASCT) was studied by unsteady numerical simulations. The results showed that both SRCT and ASCT significantly improved the stall margin and total pressure ratio at the near-stall point, and increased the efficiency loss at the peak efficiency point. The casing treatment reduced the dynamic-dynamic interference effect between the two rotors by acting on the tip leakage flow and suppressing the pressure potential flow. The flow in axial slots was related to the relative position of the rotor. The periodic sweeping of the rotor to the casing treatment slots increased the unsteadiness of flow in casing treatment slots, and the mixing of the flow in casing treatment slots was the main reason for the decrease of efficiency.
- counter-rotating axial flow compressor /
- self-recirculating casing treatment /
- axial slot casing treatment /
- unsteady /
- stability enhancement mechanism

HTML

图 1 两级对转压气机

Figure 1. Two-stage counter-rotating axial flow compressor

下载: 全尺寸图片幻灯片

图 2 网格示意图

Figure 2. Schematic diagram of grid

下载: 全尺寸图片幻灯片

图 3 网格无关性验证

Figure 3. Grid independence verification

下载: 全尺寸图片幻灯片

图 4 数值方法校核

Figure 4. Verification of numerical methods

下载: 全尺寸图片幻灯片

图 5 ASCT和SRCT结构示意图

Figure 5. Schematic diagram of SRCT and ASCT

下载: 全尺寸图片幻灯片

图 6 ASCT和SRCT网格示意图

Figure 6. Schematic diagram of grids of SRCT and ASCT

下载: 全尺寸图片幻灯片

图 7 对转压气机特性线

Figure 7. Characteristic curves of the counter-rotating axial flow compressor

下载: 全尺寸图片幻灯片

图 8 NSP2工况下R2叶顶泄漏涡随时间变化

Figure 8. Variation of R2 blade tip leakage vortex with time under the NSP2 condition

下载: 全尺寸图片幻灯片

图 9 PEP和NSP1工况下R2转子99%叶高处叶表C_p随时间的变化

Figure 9. Variation of the blade surface C_p at 99% blade span of R2 with time under the PEP and NSP1 conditions

下载: 全尺寸图片幻灯片

图 10 NSP1工况下R1和R2转子99%叶高处C_p云图分布

Figure 10. C_p contour distributions at 99% blade span of R1 and R2 under the NSP1 condition

下载: 全尺寸图片幻灯片

图 11 NSP1工况下不同时刻R1转子99%叶高处叶表C_p分布

Figure 11. C_p distribution of R1 at 99% blade span at different times under the NSP1 condition

下载: 全尺寸图片幻灯片

图 12 不同流量工况下叶表S_u分布

Figure 12. S_u distribution of blade surface under the different mass flow rate conditions

下载: 全尺寸图片幻灯片

图 13 NSP1工况下R2叶顶时均三维流线分布

Figure 13. Three-dimensional streamlines distribution at the tip of R2 under the NSP1 condition

下载: 全尺寸图片幻灯片

图 14 NSP1工况下R2进口气流角沿叶高变化

Figure 14. Distribution of R2 inlet flow angle under the NSP1 condition

下载: 全尺寸图片幻灯片

图 15 PEP工况下子午面熵的时均结果

Figure 15. Time-average result of entropy on z-r plane under the PEP condition

下载: 全尺寸图片幻灯片

图 16 PEP工况下R2转子99%叶高熵的时均结果

Figure 16. Time-average result of entropy at 99% blade span of R2 under the PEP condition

下载: 全尺寸图片幻灯片

图 17 PEP工况下CT槽内的流场

Figure 17. Flow fields in the CT slot under the PEP condition

下载: 全尺寸图片幻灯片

图 18 PEP工况下CT中不同时刻R2的TLF速度分布

Figure 18. Axial distribution of TLF of R2 at different times in the CT under the PEP condition

下载: 全尺寸图片幻灯片

表 1 对转压气机主要设计参数

Table 1. Main design parameters of the counter-rotating axial flow compressor

设计参数 IGV R1 R2 OGV

转速/10³ （r/min） 8 −8
叶顶间隙/mm 0.5 0.5
叶尖速度/（m/s） 167.6 167.6
叶片数 22 19 20 32
轮毂比 0.485 0.641

下载: 导出CSV

参考文献(26)

[1]	VIJAYRAJ K, GOVARDHAN M. Aerodynamics of contra-rotating fans with swept blades[R]. ASME Paper GT2015-1383, 2015.
[2]	韩少冰,张雯棋,钟兢军. 跨声速风扇转子叶尖小翼设计与扩稳机理研究[J]. 推进技术,2020,41(7): 1484-1492. doi: 10.13675/j.cnki.tjjs.190551 HAN Shaobing,ZHANG Wenqi,ZHONG Jingjun. Research on design of blade tip winglet for transonicfan rotor and mechanism of stability enhancement[J]. Journal of Propulsion Technology,2020,41(7): 1484-1492. (in Chinese) doi: 10.13675/j.cnki.tjjs.190551
[3]	CHEN Y,YANG L,ZHONG J. Numerical study on endwall fence with varying geometrical parameters in a highly-loaded compressor cascade[J]. Aerospace Science and Technology,2019,94: 105390.1-105390.10.
[4]	MA S, CHU W, ZHANG H, et al. Impact of a combination of micro-vortex generator and boundary layer suction on performance in a high-load compressor cascade[R]. ASME Paper GT2018-75520, 2018.
[5]	SHI L,LIU B,NA Z,et al. Experimental investigation of a counter-rotating compressor with boundary layer suction[J]. Chinese Journal of Aeronautics,2015,28(4): 1044-1054. doi: 10.1016/j.cja.2015.05.003
[6]	KHALEGHI H. Parametric study of injector radial penetration on stalling characteristics of a transonic fan[J]. Aerospace Science and Technology,2017,66: 112-118. doi: 10.1016/j.ast.2017.02.020
[7]	LI J. Self-adaptive stability-enhancing technology with tip air injection in an axial flow compressor[J]. Journal of Turbomachinery,2017,139(1): 81-89.
[8]	楚武利,卢新根,吴艳辉. 带周向槽机匣处理的压气机内部流动数值模拟与试验[J]. 航空动力学报,2006,21(1): 100-105. doi: 10.3969/j.issn.1000-8055.2006.01.019 CHU Wuli,LU Xingen,WU Yanhui. Numerical and experimental investigations of the flow in a compressor with circumferential grooves[J]. Journal of Aerospace Power,2006,21(1): 100-105. (in Chinese) doi: 10.3969/j.issn.1000-8055.2006.01.019
[9]	DAY I J. Stall, surge, and 75 years of research[J]. Journal of Turbomachinery,2016,138(1): 1-16.
[10]	CHEN H, KOLEY S S, LI Y, et al. Systematic experimental evaluations aimed at optimizing the geometry of axial casing groove in a compressor[R]. ASME Paper GT2019-91050, 2019.
[11]	BRANDSTETTER C,WARTZEK F,WERNER J,et al. Unsteady measurements of periodic effects in a transonic compressor with casing treatments[J]. Journal of Turbomachinery,2016,138(5): 1-9.
[12]	HATHAWAY M D. Self-recirculating casing treatment concept for enhanced compressor performance[R]. ASME Paper GT2002-30368, 2002.
[13]	STRAZISAR A J, BRIGHT M M, THORP S, et al. Compressor stall control through endwall recirculation[R]. ASME Paper GT2004-54295, 2004.
[14]	KHALEGHI H. Effect of discrete endwall recirculation on the stability of a high-speed compressor rotor[J]. Aerospace Science and Technology,2014,37: 130-137. doi: 10.1016/j.ast.2014.05.009
[15]	KHALEGHI H. A new approach of endwall recirculation in axial compressors[J]. Aerospace Science and Technology,2020,98: 105704.1-105704.7.
[16]	KUMAR S S, CHOTALIA R J, JANA S, et al. Single stage axial compressor stability management with self-recirculating casing treatment[R]. AIAA 2019-0942, 2019.
[17]	张皓光,安康,谭锋,等. 自循环机匣处理轴向位置影响扩稳能力的机理[J]. 航空动力学报,2017,32(4): 983-989. doi: 10.13224/j.cnki.jasp.2017.04.026 ZHANG Haoguang,AN Kang,TAN Feng,et al. Mechanism of affecting ability of stability enhancement with varying axial position of self-recirculating casing treatment[J]. Journal of Aerospace Power,2017,32(4): 983-989. (in Chinese) doi: 10.13224/j.cnki.jasp.2017.04.026
[18]	LI Jichao,DU Juan,NAN Xi,et al. Coupling stability-enhancing mechanism with compact self-recirculating injection in an axial flow compressor[J]. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy,2016,230(7): 696-708. doi: 10.1177/0957650916659778
[19]	LI Jichao,DU Juan,LI Zhiyuan,et al. Stability enhancement with self-recirculating injection in axial flow compressor[J]. Journal of Turbomachinery,2018,140(7): 1001-1013.
[20]	GUINET C,INZENHOFER A,GÜMMER V. Influencing parameters of tip blowing interacting with rotor tip flow[J]. Journal of Turbomachinery,2017,139(2): 101-110.
[21]	晏松,楚武利. 不同转速下自循环机匣处理对转子性能的影响[J]. 航空动力学报,2019,34(11): 2516-2528. doi: 10.13224/j.cnki.jasp.2019.11.024 YAN Song,CHU Wuli. Effect of self-circulating treatment casing on rotor performance at different speeds[J]. Journal of Aerospace Power,2019,34(11): 2516-2528. (in Chinese) doi: 10.13224/j.cnki.jasp.2019.11.024
[22]	PUNDHIR D S. A study of some factors affecting the effectiveness of casing treatment in contra-rotating axial compressor stage[J]. Indian Journal of Engineering and Materials Sciences,1994,1: 199-207.
[23]	MAO X,LIU B,ZHAO H. Numerical analysis of the circumferential grooves casing treatment in a counter-rotating axial flow compressor[J]. Applied Thermal Engineering,2018,130: 29-39. doi: 10.1016/j.applthermaleng.2017.11.044
[24]	MAO X,LIU B,TANG T,et al. The impact of casing groove location on the flow instability in a counter-rotating axial flow compressor[J]. Aerospace Science and Technology,2018,76: 250-259. doi: 10.1016/j.ast.2018.01.037
[25]	HEINRICH M, KHALEGHI H, FRIEBE C. Numerical investigation of circumferential groove casing treatment on a low speed contra-rotating fan[R]. ASME Paper GT2019-91705, 2019.
[26]	SUN X,DONG X,SUN D. Recent development of casing treatments for aero-engine compressors[J]. Chinese Journal of Aeronautics,2019,32(1): 1-36. doi: 10.1016/j.cja.2018.11.005