泛结构条件下轴承腔油气两相流动的模化方法

孙恒超; 陈国定; 陈薄

doi:10.13224/j.cnki.jasp.2014.08.029

泛结构条件下轴承腔油气两相流动的模化方法

doi: 10.13224/j.cnki.jasp.2014.08.029

西北工业大学机电学院, 西安 710072

基金项目:

国家自然科学基金（50975233，51275411）；西北工业大学研究生创业种子基金（Z2012051）

详细信息

作者简介:
孙恒超（1987-），男，河北衡水人，博士生，主要从事航空发动机润滑系统设计研究。

中图分类号: V233.4
计量
- 文章访问数: 1394
- HTML浏览量: 3
- PDF量: 818
- 被引次数: 0
出版历程
- 收稿日期: 2013-05-07
- 刊出日期: 2014-08-28

Modeling method of bearing chamber oil/air two-phase flow under multi-geometrical conditions

School of Mechanical Engineering, Northwestern Polytechnical University, Xi'an 710072, China

摘要

摘要: 首先根据热力学、流体力学的基本定理对航空发动机轴承腔油气两相流动的相似性进行了数学推导，获得了弗劳德数、欧拉数、雷诺数、普朗特数和埃克特数等相似准则数，遵循系统几何相似和动力相似等相似准则建立了航空发动机泛结构及工况条件下轴承腔油气两相流动的模化模型；并对实际轴承腔及模化轴承腔的油气两相流场进行了数值求解，模化轴承腔与实际轴承腔无量纲速度、温度和压力分布一致性较好，支持了提出的轴承腔油气两相流动相似准则和模化方法的可靠性.泛结构条件下轴承腔油气两相流动模化方法对于指导轴承腔油气两相流动试验设计及推进理论分析向航空发动机工程设计转化都有一定的参考价值.
- 模化 /
- 航空发动机 /
- 轴承腔 /
- 两相流 /
- 相似准则 /
- 方程分析法 /
- 流场
Abstract: The similarity of oil/air two-phase flow in aero-engine bearing chambers was derived according to the basic theorems of thermodynamic and fluid dynamic firstly, the similarity criterion numbers such as Froude number, Euler number, Reynolds number, Prandtl number and Eckert number were obtained, then the model of aero-engine bearing chamber oil/air two-phase flow was built under multi-geometrical and operating conditions following the principle of system similarity. The oil/air two-phase flow fields of prototype and modeling bearing chambers were solved by numerical simulation, and the better consistency of flow fields dimensionless physical characteristic parameters, such as dimensionless tangential velocity, temperature and pressure between prototype and modeling bearing chambers, illustrates that the similarity criterion numbers and modeling method of aero-engine bearing chamber oil/air two-phase flow proposed are reliable. The proposal modeling method has certain reference value for guiding experiment design of bearing chamber oil/air two-phase flow as well as promoting the shift of theory investigation to engineering application of aeroengine lubrication system design.
- modeling /
- aero-engine /
- bearing chamber /
- two-phase flow /
- similarity criterion /
- equation-based analysis method /
- flow fields

HTML

参考文献(16)

[1]	Wittig S,Glahn A,Himmelsbach J.Influence of high rotational speeds on heat transfer and oil film thickness in aero- engine bearing chambers[J].ASME Transactions Journal of Engineering for Gas Turbines and Power,1994,116(2):395-401.
[2]	Glahn A,Wittig S.Two-phase air/oil flow in aero engine bearing chambers:characterization of oil film flows[J].Journal of Engineering for Gas Turbines and Power,1996,118(3):578-583.
[3]	Farrall M,Simmons K,Hibberd S,et al.A numerical model for oil film flow in an aeroengine bearing chamber and comparison to experimental data[J].Journal of Engineering for Gas Turbines and Power,2006,128(1):111-117.
[4]	Glahn A,Busam S,Wittig S.Local and mean heat transfer coefficients along the internal housing walls of aero engine bearing chambers[R].ASME Paper 1997-GT-261,1997.
[5]	Busam S,Glahn A,Wittig S.Internal bearing chamber wall heat transfer as a function of operating conditions and chamber geometry[J].Journal of En gineering for Gas Turbines and Power,2000,122(2):314-320.
[6]	Lee C W,Palma P C,Simmons K,et al.Comparison of computational fluid dynamics and particle image velocimetry data for the airflow in an aeroengine bearing chamber[J].Journal of Engineering for Gas Turbines and Power,2005,127(4):697-703.
[7]	XU Rangshu,WANG Juanjuan,CHEN Xiaowen,et al.Numerical simulation of two-phase air/oil flow characteristic in bearing chamber[C]//International Conference on Electric Information and Control Engineering.Wuhan:IEEE,2011:2412-2415.
[8]	汪友勇,王锁芳,艾俊峰,等.轴承腔油气两相流数值模拟的试验验证[J].航空动力学报,2013,28(3):629-635. WANG Youyong,WANG Suofang,AI Junfeng,et al.Experimental verification of numerical simulation of oil-air two-phase flow in bearing chamber[J].Journal of Aerospace Power,2013,28(3):629-635.(in Chinese)
[9]	孙恒超,陈国定,陈薄.航空发动机涡轮前支承轴承腔油气两相物理场分析[J].西北工业大学学报,2013,31(1):71-76. SUN Hengchao,CHEN Guoding,CHEN Bo.Physical fields of oil/air two-phase in aeroengine bearing chamber in front of turbine[J].Journal of Northwestern Polytechnical University,2013,31(1):71-76.(in Chinese)
[10]	吴昊天,陈国定.航空发动机轴承腔润滑的气液两相均匀流研究[J].摩擦学学报,2007,27(1):78-82. WU Haotian,CHEN Guoding.Homogeneous flow of two-phase gas/liquid flow in aero-engine bearing chamber[J].Tribology,2007,27(1):78-82.(in Chinese)
[11]	陈国定,刘曼利,刘亚军,等.不同流型下轴承腔中油气介质的流动特征参数[J].航空学报,2010,31(12):2400-2406. CHEN Guoding,LIU Manli,LIU Yajun,et al.Characteristic flow parameters of oil/air lubricants in bearing chamber under different flow patterns[J].Acta Aeronautica et Astronautica Sinica,2010,31(12):2400-2406.(in Chinese)
[12]	Farrall M,Hibberd S,Simmons K,et al.Prediction of air/oil exit flows in a commercial aero-engine bearing chamber[J].Journal of Aerospace Engineering,2006,220(3):197-202.
[13]	Josef K.Similarity and modeling in science and engineering[M].London:Cambridge International Science Publishing Ltd.,2012.
[14]	陶文铨.传热学[M].西安:西北工业大学出版社,2006.
[15]	林基恕.航空发动机设计手册:第12册传动与润滑系统[M].北京:航空工业出版社,2002.
[16]	Gorse P,Busam S,Dullenkopf K.Influence of operating condition and geometry on the oil film thickness in aeroengine bearing chambers[J].Journal of Engineering for Gas Turbines and Power,2006,128(1):103-110.