Numerical analysis on effect of cooling air pocket area on performance of air-cooled fuel injector
-
摘要: 以某型涡扇发动机加力燃烧室气冷喷油杆为研究对象,在梯形截面的风兜下底和高度不变的情况下,通过改变上底长度得到一系列不同风兜面积的几何模型,综合考虑外流场对气冷喷油杆内部流动和换热特性的影响,对其在巡航状态下进行了流/热/固耦合三维数值模拟研究,获得了不同风兜面积对气冷喷油杆引气率、冷却空气喷口流量分布、壁面平均冷却效果、壁面最高温度的影响规律.结果表明:引气率随风兜面积增大线性增大;喷油嘴凸台周围冷却空气喷口的流量沿气冷喷油杆内冷却空气流向呈二次曲线规律变化,且随风兜面积增大分布趋于均匀;随风兜面积增大,喷油杆、隔热套壁面平均冷却效果线性增大,壁面最高温度降低;有效抑制内涵高温燃气倒灌进入隔热套是避免喷油杆局部高温的关键.Abstract: Based on an air-cooled fuel injector in an afterburner of turbofan engine,geometric models cooling air pocket areas with different were obtained by changing the the upper bottom length of trapezoidal section cooling air pocket,but with the constant down bottom and height.Considering the effect of the external flow field on the internal flow and heat transfer characteristics of air-cooled fuel injector comprehensively, its conjugate heat transfer three-dimensional numerical simulation was conducted on the cruise flying state, so as to get an effect laws of different cooling air pocket areas on the entraining rate of air-cooled fuel injector,the mass flow rate of cooling air nozzle, the average cooling effectiveness and the maximum wall temperature. Results shows that, the entraining rate increases linearly with the increasing of cooling air pocket area; the mass flow rate of cooling air nozzle around the fuel nozzle convex platform changes by conic rule along the air-cooled fuel injector axis, firstly increases and then decreases; the mass flow rate tends to be uniform with increasing of cooling air pocket area; the fuel injector's and insulated jacket's average cooling effectiveness increases linearly and the maximum wall temperature decreases with the increasing of cooling air pocket area; inhibiting effectively the backflow of the hot gas into the insulated jacket is the key to avoid a partial high wall temperature.
-
[1] Carrier D,de Champlain A.Direct fuel injection for bluff body flame stabilization[J].AIAA 96-3032,1996. [2] Shinbo K,Koide T,Kashiwagi T,et al.Research of heat transfer of a liner for an afterburner[J].AIAA 97-3005,1997. [3] 徐志刚,刘贵才.某型发动机加力燃油总管喷油杆断裂分析[J].宇航材料工艺,2002,32(4):58-61. XU Zhigang,LIU Guicai.Failure analysis of main fluid pipe in one aero-engine[J].Aerospace Materials and Technology,2002,32(4):58-61.(in Chinese) [4] Peat A E.Thermal decomposition of aviation fuel[R].ASME Paper 82-GT-27,1982. [5] 郭成富,王勇,曹康.加力燃烧室喷油杆结焦试验研究[J].燃气涡轮实验与研究,1997(1):26-31. [6] Branstetter J R.Afterburner performance of circular V-gutters and a sector of parallel V-gutters for a range of inlet temperatures to 1255K[R].NASA-TN-D-7212,1995. [7] XIAO Yumin,Amano R S.A study on effective heat transfer characteristics in an afterburner with ceramic stabilizer[J].AIAA-2003-338,2003. [8] 王俭,顾善建,杨茂林,等.直射式喷嘴跨流喷射的雾化特性实验研究[J].航空学报,1990,11(4):157-164. WANG Jian,GU Shanjian,YANG Maolin,et al.Study on atomization features of a plain injector in high speed transverse air stream[J].Acta Aeronautica et Astronautica Sinica,1990,11(4):157-164.(in Chinese) [9] 孙雨超,张志学,李江宁,等.一体化加力燃烧室方案设计及数值研究[J].航空科学技术,2011(4):71-74. SUN Yuchao,ZHANG Zhixue,LI Jiangning,et al.Design and numerical research of integrated rear frame and afterburner[J].Aeronautical Science and Technology,2011(4):71-74.(in Chinese) [10] 白兴艳,张频捷,岳连捷,等.加力用气冷与气动雾化喷油杆的性能研究[J].航空动力学报,2000,15(4):391-396. BAI Xingyan,ZHANG Pinjie,YUE Lianjie,et al.Experimental study on performance of air cooling/atomizing fuel injector bar in afterburner[J].Journal of Aerospace Power,2000,15(4):391-396.(in Chinese) [11] 李瑞明,岳明,樊未军,等.加力用气冷与气动雾化喷油杆冷却性能数值模拟[J].航空发动机,2005,31(2):38-41. LI Ruiming,YUE Ming,FAN Weijun,et al.Numerical simulation of the cooling performance of an afterburner air blast spray bar[J].Aeroengine,2005,31(2):38-41.(in Chinese) [12] 杨威荣.加力喷油杆冷却方案研究[D].北京:北京航空航天大学,2005. YANG Weirong.Study on the afterburner fuel injector cooling scheme[D].Beijing:Beijing University of Aeronautics and Astronautics,2005.(in Chinese) [13] 闫宝华,樊未军,杨茂林.加力燃烧室双层喷油杆内冷却气流动特性[J].航空动力学报,2008,23(7):1182-1188. YAN Baohua,FAN Weijun,YANG Maolin.Cooling air flow performance of an afterburner fuel injector with double-wall construction[J].Journal of Aerospace Power,2008,23(7):1182-1188.(in Chinese) [14] 张勃,李继保,吉洪湖,等.冲击-多斜孔壁复合冷却中冲击孔与多斜孔面积比对换热特性的影响[J].航空动力学报,2009,24(10):2235-2240. ZHANG Bo,LI Jibao,JI Honghu,et al.Effect ofarea ratio of impingement hole to effusion hole on heat transfer characteristics of impingement-effusion composite cooling[J].Journal of Aerospace Power,2009,24(10):2235-2240.(in Chinese) [15] 吴博,张靖周,单勇,等.加遮挡罩二元喷管红外辐射特性数值研究[J].航空动力学报,2011,26(10):2287-2292. WU Bo,ZHANG Jingzhou,SHAN Yong,et al.Numerical research on infrared radiation characteristics of two-dimension nozzle with shelter covering[J].Journal of Aerospace Power,2011,26(10):2287-2292.(in Chinese)
点击查看大图
计量
- 文章访问数: 1024
- HTML浏览量: 1
- PDF量: 508
- 被引次数: 0