Method of generating airfoil manufacturing coordinates based on cold airfoil
-
摘要: 建立了基于冷态叶型生成叶片加工坐标的方法,包括排序、插值加密、叠加位移量、去倒圆及端区叶型拟合等步骤.以某多级轴流压气机为例,应用该方法生成的加工坐标叶片除端区外主流通道叶高内误差在0.01mm以下,叶片表面波纹度和前后缘曲率良好.通过进口级的数值模拟表明:该方法生成的加工坐标叶片与冷态叶型的误差对气动性能影响小,流量-总压比-等熵效率特性变化微小,叶片进出口气流速度、方向及流场细节等变化较小,满足工程应用的需求.Abstract: Method of generating airfoil manufacturing coordinates based on cold airfoil was proposed. It comprised of ordering, interpolating, adding location bias, removing endwall fillet, and fitting endwall airfoil. This method was used to generate multistage axial compressor blade manufacturing coordinates. The difference between manufacturing coordinates and the cold airfoil below 0.01mm except near endwall section was found. Both the waviness of blade surface and curvature of leading or trailing edges were acceptable. Numerical results show the difference between manufacturing coordinate airfoil and cold airfoil has less impact on aerodynamic performance. Mass flow versus total pressure ratio and isentropic efficiency characteristics change little. Besides, flow velocity and flow angle of blade row inlet and outlet, and the detailed flow field have almost no changes. This method can be applied for generating airfoil manufacturing coordinates.
-
Key words:
- cold airfoil /
- manufacturing coordinate /
- generating method /
- aerodynamic performance /
- axial compressor
-
[1] Wilson M J,Imregun M,Sayma A I.The effect of stagger variability in gas turbine fan assemblies[J].Journal of Turbomachinery,2007,129(2):404-411. [2] Janke C,Karger K,Gaun L,et al.3D CFD compressor map computation process accounting for geometry changes due to off-design operation loads[R].ASME Paper 2014-GT-26131,2014. [3] Benini E.Three-dimensional multi-objective design optimization of a transonic compressor rotor[J].Journal of Propulsion and Power,2004,20(3):559-565. [4] 张正秋,邹正平,刘宝杰.高负荷风扇叶片重心线调节对叶片强度和气动性能的影响分析[J].航空学报,2006,27(3):380-385. ZHANG Zhengqiu,ZOU Zhengping,LIU Baojie.Influence of gravity center modification on structural strength and aerodynamic performance of blade in high load fan blade design[J].Acta Aeronautica et Astronautica Sinica,2006,27(3):380-385.(in Chinese) [5] 郑赟,田晓,杨慧.跨声速风扇叶片变形对气动性能的影响[J].航空动力学报,2011,26(7):1621-1627. ZHENG Yun,TIAN Xiao,YANG Hui.Impact of blade deflection on aerodynamic performance of a transonic fan[J].Journal of Aerospace Power,2011,26(7):1621-1627.(in Chinese) [6] 杨慧,沈真,郑赟.叶片反扭对跨声速大涵道比风扇性能的影响[J].航空动力学报,2016,31(1):100-105. YANG Hui,SHEN Zhen,ZHENG Yun.Influence of blade untwist on transonic high bypass ratio fan performance[J].Journal of Aerospace Power,2016,31(1):100-105.(in Chinese) [7] 郑赟,王彪,杨慧,等.跨声速风扇叶片反扭影响因素研究[J].燃气涡轮试验与研究,2013,26(5):7-11. ZHENG Yun,WANG Biao,YANG Hui,et al.Blade untwist influencing factors of a transonic fan[J].Gas Turbine Experiment and Research,2013,26(5):7-11.(in Chinese) [8] 周正贵.压气机/风扇叶片自动优化设计的研究现状和关键技术[J].航空学报,2008,29(2):257-266. ZHOU Zhenggui.Current situations and key techniques of automatic aerodynamic design of compressor/fan blades[J].Acta Aeronoutica et Astronautica Sinica,2008,29(2):257-266.(in Chinese) [9] 王咏梅,陈葆实.罩量调节对风扇/压气机气动性能和强度影响的研究[J].航空发动机,2000,26(1):6-11. WANG Yongmei,CHEN Baoshi.The effect of the modification of gravity center eccentricity on aerodynamics performance and structural strength of fan/compressor[J].Aeroengine,2000,26(1):6-11.(in Chinese) [10] Gaun L,Bestle D,Huppertz A.Hot-to-cold CAD geometry transformation of aero engine parts based on B-spline morphing[R].ASME Paper 2014-GT-26683,2014. [11] Timon V P,Corral R.A study on the effects of geometric non linearities on the un-running transformation of compressor blades[R].ASME Paper 2014-GT-25638,2014. [12] YANG Hui,ZHENG Yun.A fluid-structure coupling method for rotor blade un-running design[R].ASME Paper 2013-GT-94653,2013. [13] 王振培,王丹,朱继宏,等.叶片参数化有限元建模与罩量优化设计[J].航空动力学报,2011,26(11):2450-2458. WANG Zhenpei,WANG Dan,ZHU Jihong,et al.Parametrical FE modeling of blade and design optimization of its gravity center eccentricity[J].Journal of Aerospace Power,2011,26(11):2450-2458.(in Chinese) [14] 郑赟,王彪,杨慧.跨声速风扇叶片的反扭设计研究[J].机械工程学报,2013,49(5):147-153. ZHENG Yun,WANG Biao,YANG Hui.Numerical study on blade un-running design of a transonic fan[J].Journal of Mechanical Engineering,2013,49(5):147-153.(in Chinese) [15] 王延荣,黄钟山,付志忠,等.基于热态叶型的小轮毂比弯掠叶片结构保形设计与优化[J].航空动力学报,2015,30(10):2305-2311. WANG Yanrong,HUANG Zhongshan,FU Zhizhong,et al.Structural design and optimization for the deformation approaching to hot profile of a swept fan blade with smaller hub-to-tip ratio[J].Journal of Aerospace Power,2015,30(10):2305-2311.(in Chinese) [16] 王荣桥,林丹,樊江.基于特征的压气机叶片结构设计[J].航空发动机,2004,30(2):5-9. WANG Rongqiao,LIN Dan,FAN Jiang.Feature-based structure design of compressor blades[J].Aeroengine,2004,30(2):5-9.(in Chinese) [17] 王振培,王丹,杨军刚,等.航发叶片有限元建模与罩量优化设计系统开发[J].机械制造,2011,49(6):15-18. WANG Zhenpei,WANG Dan,YANG Jungang,et al.Development of the system for finite element modeling and offset optimization of turbine blades[J].Machinery,2011,49(6):15-18.(in Chinese) [18] 陆山,鲁冯杰.基于ANSYS的整体叶盘结构优化设计[J].航空动力学报,2012,27(6):1218-1224. LU Shan,LU Fengjie.Optimization design method of blisk based on the ANASYS[J].Journal of Aerospace Power,2012,27(6):1218-1224.(in Chinese) [19] 朱心雄.自由曲线曲面造型技术[M].北京:科学出版社,2000.
点击查看大图
计量
- 文章访问数: 815
- HTML浏览量: 0
- PDF量: 484
- 被引次数: 0