膨胀规律可控的轴对称基准流场设计方法

南向军; 张留欢; 李永洲

doi:10.13224/j.cnki.jasp.2017.05.014

膨胀规律可控的轴对称基准流场设计方法

doi: 10.13224/j.cnki.jasp.2017.05.014

中国航天科技集团公司西安航天动力研究所，西安 710100

计量
- 文章访问数: 841
- HTML浏览量: 3
- PDF量: 11
- 被引次数: 0
出版历程
- 收稿日期: 2015-08-20
- 刊出日期: 2017-05-28

Design method of axisymmetric basic flowfield with controlled expansion law

摘要

摘要: 为了提高流线追踪喷管设计方法的灵活性，从推力和力矩两方面考虑，引入特殊中心体，探索了壁面膨胀规律可控的轴对称基准流场设计方法.设计过程中利用特征线理论（MOC）实现了由膨胀规律求解气动壁面的反设计.针对基准流场的主要设计参数，包括膨胀规律、中心体及斜倾角等进行了参数化研究，得到了设计参数对基准流场结构及性能的影响规律.利用该基准流场，设计了矩形截面的流线追踪喷管(导出喷管)，并进行了分析.结果表明：利用特征线理论可以实现膨胀规律到壁面的反设计；在进口参数和落压比一定的条件下，存在一定的膨胀规律使得基准流场的内推力最大；流场的中心体尺度和长度比对推力影响很小，可作为调整导出喷管力矩的设计参数；出口斜倾角增大会导致基准流场的长度减小，同时推力下降明显，设计时应综合考虑.
- 高超声速 /
- 喷管 /
- 基准流场 /
- 膨胀规律 /
- 力矩
Abstract: In order to make the design methodology of streamline traced nozzle more flexible, an innovative axis symmetrical basic flow field design methodology with controlled expansion law on wall was explored while a centre body was placed in the flowfield. In the design process, Method of characteristics (MOC) was used to inversely solve the wall with given expansion law. The main design parameters, such as expansion law, centre body and oblique angle, were parametrically investigated. Then the variation of structure and performance of basic flowfield with these parameters were obtained. Using this basic flowfield, a rectangular streamline traced nozzle was designed and analyzed. Results show that, inverse design can be achieved by MOC; when the inlet and exit flow parameters are stable, there is a suitable expansion law corresponding to the maximum thrust performance. The radius of centre body and length ratio of basic flowfield, with less effect on thrust, can be used as the parameters to optimize the moment characteristics of derivative nozzle. When the oblique angle increases, the length and thrust of basic flowfield decrease rapidly, so the choice of oblique angle should be considered carefully.
- hypersonic /
- nozzle /
- basic flowfield /
- expansion law /
- moment

HTML

参考文献(18)

[1]	Cockrell C E,Jr,Auslender A H,White J A.Aeroheating predictions for the X-43 cowl-closed configuration at Mach 7 and 10［R］.AIAA-2002-0218,2002.
[2]	Hank J M,Murphy J S,Mutzman R C.The X-51A scramjet engine flight demonstration program［R］.AIAA-2008-2540,2008.
[3]	Small W J,Weidner J P,Johnston P J.Scramjet nozzle design and analysis as applied to a highly integrated hypersonic research airplane［R］.NASA TND-8334,1974.
[4]	张堃元,张荣学,徐辉.非对称大膨胀比喷管研究［J］.推进技术,2001,22(5):380-382.ZHANG Kunyuan,ZHANG Rongxue,XU Hui.Investigation of single expansion ramp nozzle［J］.Journal of Propulsion Technology,2001,22(5):380-382.(in Chinese)
[5]	张艳慧,徐惊雷,张堃元.超燃冲压发动机非对称喷管设计点性能［J］，推进技术,2007,28(3):282-286.ZHANG Yanhui,XU Jinglei,ZHANG Kunyuan.Numerical simulation of single expansion ramp nozzle for scramjet on the designing point［J］.Journal of Propulsion Technology,2007,28(3):282-286.(in Chinese)
[6]	Evvard J,Maslen S.Three-dimensional supersonic nozzles and inlets of arbitrary exit cross section［R］.NACA-TN-2688,1952.
[7]	Mlder S.Internal,axisymmetric,conical flow［J］.AIAA Journal,1967,5(7):1252-1255.
[8]	Billig F S.SCRAM:a supersonic combustion ramjet missile ［R］.AIAA 93-2329,1993.
[9]	Smart M K.Design of three-dimensional hypersonic inlets with rectangular to elliptical shape transition［R］.AIAA 98-0960,1998.
[10]	南向军,张堃元,金志光,等.压升规律可控的高超声速内收缩进气道设计［J］.航空动力学报,2011,26(3):518-523.NAN Xiangjun,ZHANG Kunyuan,JIN Zhiguang,et al.Investigation on hypersonic inward turning inlets with controlled pressure gradient［J］.Journal of Aerospace Power,2011,26(3):518-523.(in Chinese)
[11]	卢鑫，岳连捷，肖雅彬，等.超燃冲压发动机尾喷管流线追踪设计［J］.推进技术,2011,32(1):91-95.LU Xin，YUE Lianjie，XIAO Yabin，et al.Design of scramjet nozzle based on streamline tracing technique［J］.Journal of Propulsion Technology,2011,32(1):91-95.(in Chinese)
[12]	Mo J,Xu J L,Gu R,et al.Design of a circular to rectangular transition scramjet nozzle with streamline tracing technique［R］.AIAA-2012-5885,2012.
[13]	高太元,崔凯,王秀平,等.三维后体/尾喷管一体化构型优化设计及性能分析［J］.科学通报,2012,57(4):239-247.GAO Taiyuan,CUI Kai,WANG Xiuping,et al.Aerodynamic optimization and evaluation for the three-dimensional afterbody/nozzle integrated configuration of hypersonic vehicles［J］.Chinese Science Bulletion,2012,57(4):239-247.(in Chinese)
[14]	徐大军,陈兵,蔡国飙,等.高超声速飞行器后体喷管三维构型设计［J］.航空动力学报,2009,24(2):247-254.XU Dajun,CHEN Bing,CAI Guobiao,et al.Design of three dimensional afterbody/nozzle configuration of airbreathing hypersonic vehicle［J］.Journal of Aerospace Power,2009,24(2):247-254.(in Chinese)
[15]	Elvin J D.Integrated inward turning inlets and nozzles for hypersonic air vehicle:US07102293.3［P］.2007-02-13.
[16]	Kothari A P,Livingston J W,Tarpley C,et al.Rocket based combined cycle hypersonic vehicle design for orbital access［R］.AIAA-2011-2338,2011.
[17]	莫建伟，徐惊雷，全志斌，等．考虑进口非均匀的喷管设计及冷流条件下的性能研究［J］．航空学报，2014,35(3):706-713．MO Jianwei,XU Jinglei,QUAN Zhibin,et al.Design and cold flow experiment of a scramjet nozzle considering nonuniform entrance flow effects［J］.Acta Aeronautica et Astronautica Sinica,2014,35(3):706-713．(in Chinese)
[18]	赵强,徐惊雷,于洋.基于膨胀度可控的SERN设计及试验验证［J］.航空学报,2014,35(1):125-131.ZHAO Qiang,XU Jinglei,YU Yang.Design and experimental validation of SERN based on controllable expansion degree distribution［J］.Acta Aeronautica et Astronautica Sinica,2014,35(1):125-131.(in Chinese)