湿压缩对压气机转子失稳边界工况性能的影响

杨国伟; 吴艳辉; 安光耀; 陈智洋

doi:10.13224/j.cnki.jasp.2018.04.006

湿压缩对压气机转子失稳边界工况性能的影响

doi: 10.13224/j.cnki.jasp.2018.04.006

1.
西北工业大学动力与能源学院，西安 710072
2.
先进航空发动机协同创新中心，北京 100191

基金项目: 国家自然科学基金重点项目子项目(51536006)；国家自然科学基金面上项目(11572257，51276148)；航空科学基金(2015ZB53027)；西北工业大学研究生创意创新种子基金(Z2017021)

计量
- 文章访问数: 812
- HTML浏览量: 9
- PDF量: 774
- 被引次数: 0
出版历程
- 收稿日期: 2016-10-09
- 刊出日期: 2018-04-28

Influence of wet compression on performance of compressor rotor working at its stall boundary

摘要

摘要: 针对某型跨声速压气机转子的失速边界工况，采用数值模拟方法系统研究了不同加湿条件对其性能的影响。获得了水滴粒径、速度、温度和喷水量与转子进气流量、压比、效率、比压缩功等性能参数之间的关系曲线。结果表明：在失速边界上对跨声速压气机进气加湿，可以增加空气流量，提高总压比和效率，降低比压缩功。通过对流场的分析，发现进气加湿后，向低能区注入了高动量的水滴颗粒，削弱叶顶阻塞团，将主流与泄漏流交界面和激波位置向下游推进，减小激波强度，降低叶顶载荷，增大主流区载荷，改善了叶顶流场。提出了以水滴的面积流量定量评价不同进气加湿条件对叶顶流场的作用效果。
- 湿压缩 /
- 进气加湿 /
- 跨声速转子 /
- 轴流压气机 /
- 叶顶
Abstract: At the stall boundary condition of a transonic compressor rotor, numerical simulation method was used to study the effects on operation performance with different inlet fogging conditions. Correlation curves between performance parameters, including air flow, total pressure ratio, isentropic efficiency and specific work, and inlet fogging parameters, including water droplet diameter, velocity, temperature and water spray rate, were obtained. Results showed that inlet fogging can increase air flow, heighten total pressure ratio, enhance isentropic efficiency and reduce specific work. Through analyzing the flow field in detail, it was found that inlet fogging can inject high momentum water droplet to tip stagnation zone, decrease blockage region, move down the interface between main flow and leakage flow, weaken the strength of shock, reduce tip load and increase load at mainstream region. A parameter named water droplet area flow was taken to evaluate the effect on flow field with different fogging conditions quantitatively.
- wet compression /
- inlet fogging /
- transonic rotor /
- axial compressor /
- tip

HTML

参考文献(19)

[1]	ISTVAN S,MARK G.A numerical study of water injection on transonic compressor rotor performance［R］.AIAA-2007-0017,2007.
[2]	BIANCHI M,MELINO F,PERETTO A,et al.Influence of water droplet size and temperature on wet compression［R］.ASME Paper GT2007-27458,2007.
[3]	SUN Lanxin,ZHENG Qun,BHARGAVA R.The effects of wet compression on the separated flow in a compressor stage［R］.ASME Paper GT2008-50920,2008.
[4]	KLEINSCHMIDT R V.Value of wet compression in gas turbine cycles［J］.Mechanical Engineering,1947,69(2):115-116.
[5]	ROUMELIOTIS I,MATHIOUDAKIS K.Water injection effects on compressor stage operation［J］.Journal of Engineering for Gas Turbines and Power,2007,129(3):778-784.
[6]	DAY I,WILLIAMS J,FREEMAN C.Rain ingestion in axial flow compressors at part speed［J］.Journal of Turbomachinery,2008,130(1):011024.1-011024.10.
[7]	HORLOCK J H.Compressor performance with water injection［R］.ASME Paper GT2001-0343,2001.
[8]	UTAMURA M.A new gas turbine cycle for economical power boosting［R］.ASME Paper AA97-142,1997.
[9]	MEACOCK A J,WHITE A J.The effect of water injection on mutispool gas turbine behavior［J］.Journal of Engineering for Gas Turbines and Power,2006,128(1):97-102.
[10]	PAYNE R C,WHITE A J.Three-dimensional calculations of eraporative flow in compressor blades rows［R］.ASME Paper GT2007-27331,2007.
[11]	SUN Lanxin,LI Yijin,ZHENG Qun.The effects of wet compression on the separater flow in a compressor stage［R］.ASME Paper GT2008-50920,2008.
[12]	REID L,MOORE R D.Design and overall performance of four highly-loaded,high-speed inlet stages for an advanced high-pressure-ratio core compressor［R］.NASA TP1978-1337,1978.
[13]	HERRICK G P,HATHAWAY M D,CHEN J P.Unsteady full annulus simulations of a transonic axial compressor stage［R］.AIAA-2009-1059,2009.
[14]	HILL P G.Aerodynamic and thermodynamic effects of coolant injection on axial compressors［J］.Aeronautical Quarterly,1963,14(4),331-348.
[15]	EISFELD T,JOOS F.Experimental investigation of two-phase flow phenomena in transonic compressor cascades［R］.ASME Paper GT2009-59365,2009.
[16]	CHEN J P,HATHAWAY M D.Pre-stall behavior of a transonic axial compressor stage via time-accurate numerical simulation［R］.ASME Paper GT2007-27926,2007.
[17]	VO H D,TAN C S,GREITZER E M.Criteria for spike initiated rotating stall［R］.ASME Paper GT2005-68374,2005.
[18]	ANISH S,HEUY D K.Effect of wet compression on the flow behavior of a centrifugal compressor:a CFD analysis［R］.ASME Paper GT2014-25035,2014.
[19]	PUTERBAUGH S L,BRENDEL M.Tip clearance flow-shock interaction in a transonic compressor rotor［J］.Journal of Propulsion and Power,1997,13(1):24-30.