基于CFD的某减速器飞溅润滑仿真分析与验证

李玉哲; 艾永生; 刘卫真

doi:10.13224/j.cnki.jasp.2020.07.016

基于CFD的某减速器飞溅润滑仿真分析与验证

doi: 10.13224/j.cnki.jasp.2020.07.016

计量
- 文章访问数: 471
- HTML浏览量: 33
- PDF量: 466
- 被引次数: 0
出版历程
- 收稿日期: 2019-10-25
- 刊出日期: 2020-07-28

Splash lubrication simulation analysis and verification of a gearbox based on CFD

Science and Technology on Helicopter Transmission Laboratory,Hunan Aviation Powerplant Research Institute,Aero Engine Corporation of China,Zhuzhou Hunan 412002,China

摘要

摘要: 为评估飞溅润滑减速器的储油结构是否合理,基于计算流体动力学方法,建立了包含机匣、螺旋锥齿轮等构件的某减速器飞溅润滑动态仿真模型,开展了气液两相流飞溅润滑流体仿真计算与分析,获得了减速器内部的滑油运动轨迹及分布云图。通过仿真分析可以发现:输入端油兜收集到的滑油量为531 mL,大于输出端收集到的滑油量65 mL;4号油兜收集到的滑油量为0 mL,结构设计存在不合理之处,并进行了飞溅润滑试验验证。仿真分析结果与试验结果的趋势一致,验证了仿真分析方法的准确性,为飞溅润滑减速器储油结构设计提供了指导。
- 飞溅润滑减速器 /
- 计算流体动力学(CFD) /
- 流体仿真 /
- 滑油分布 /
- 飞溅润滑试验
Abstract: In order to evaluate whether the oil storage structure of splash lubricating gearbox was reasonable, a dynamic simulation model for the splash lubrication analysis of gearbox including gearbox housing, spiral bevel gear based on the computational fluid dynamics (CFD) method was established, and the splash lubrication fluid simulation calculation and analysis of gas-liquid two-phase flow were carried out, then the movement track and distribution cloud diagram of lubricating oil in gearbox were obtained. Through the simulation analysis, it was found that the amount of oil collected at input oil pocket was 531 mL, greater than the amount of oil collected at output oil pocket 65 mL, and the No4 oil pocket cant collect lubricating oil, so the design of No4 oil pocket was unreasonable. According to the result of splash lubrication test, it shows that the trend of the simulation analysis result is consistent with the experimental result, which verifys the correctness of the simulation analysis method and provids a guidance for the design of oil storage structure of splash lubricating gearbox.
- splash lubrication gearbox /
- computational fluid dynamics(CFD) /
- ,fluid simulation /
- lubricating oil distribution /
- splash lubrication test

HTML

参考文献(20)

[1]	孙丽,黄少青,仲峻峰.基于FLUENT的多回路泵流场数值模拟［J］.制造技术与机床,2010,16(1):72-73. SUN Li,HUANG Shaoqing,ZHONG Junfeng.Numerical simulation of flow field of multi-circuit pump based on FLUENT［J］.Manufacturing Technology and MachineTool,2010,16(1):72-73.(in Chinese)
[2]	张永学,李振林.流体机械内部流动数值模拟方法综述［J］.流体机械,2006,34(7):34-38. ZHANG Yongxue,LI Zhenlin.Summary of numerical simulation methods for flow in fluid machinery［J］.Fluid Machinery,2006,34(7):34-38.(in Chinese)
[3]	KVIST T.Splash lubrication simulation using CFD［J］.Delivering Drive Line Technologies,2011,11(4):1-17.
[4]	FARRALL M,SIMMONS K,HIBBERD S,et al.A numerical model for oil film flow in an aeroengine bearing chamber and comparison to experimental data［J］.Journal of Engineering for Gas Turbines and Power,2006,128(1):111-117.
[5]	WAYNE S.CFD investigation of gear pump mixing using deforming/agglomerating mesh［J］.Journal of Fluids Engineering,2007,129(4):476-484.
[6]	LEMFELD F,FRANˇA K.Numerical simulations of unsteady oil flows in the gear-boxes［J］.Journal of Applied Science in the Thermodynamics and Fluid Mechanics,2007,1(1):1-5.
[7]	JIANG Yiyao,HU Xiaozhou,HONG Shunjun,et al.Influences of an oil guide device on splash lubrication performance in a spiral bevel gearbox［J］.Tribology International,2019,136(2):155-164.
[8]	LIU H,ARFAOUI G,STANIC M,et al.Numerical modelling of oil distribution and churning gear power losses of gearboxes by smoothed particle hydrodynamics［J］.Engineering Tribology,2019,233(1):74-86.
[9]	PENG Q L,GUI L J,FAN Z J.Numerical and experimental investigation of splashing oil flow in a hypoid gearbox［J］.Engineering Applications of Computational Fluid Mechanics,2018,12(1):324-333.
[10]	LIN Yinhui,HU Zhihua.Research of flow field simulation for lubrication system and effect evaluation on a 7-speed dual clutch transmission［J］.Lecture Notes in Electrical Engineering,2013,195(3):285-298.
[11]	陈黎卿,张栋,陈无畏.基于流固耦合的分动器齿轮两相流动数值模拟与试验［J］.农业工程学报,2014,30(4):54-61. CHEN Liqing,ZHANG Dong,CHEN Wuwei.Numerical simulation and test on two-phase flow inside shell of transfer case based on fluid-structure interaction［J］.Transaction of the Chinese Society of Agricultural Engineering,2014,30(4):54-61.(in Chinese)
[12]	姜义尧,胡小舟,孙凯.某型直升机中减速器飞溅润滑流场特性分析［J］.航空动力学报,2018,33(12):3032-3040. JIANG Yiyao,HU Xiaozhou,SUN Kai.Analysis of flow field characteristics of medium reducer with splash lubrication in a certain helicoper［J］.Journal of Aerospace Power,2018,33(12):3032-3040.(in Chinese)
[13]	张志彬.机车齿轮箱温度及压力场仿真研究［D］.成都:西南交通大学,2011. ZHANG Zhibin.Simulation study on temperature and pressure field of locomotive gear box［D］.Chengdu:Southwest Jiaotong University,2011.(in Chinese)
[14]	孙凯,刘少军,胡小舟.基于动网格的中减速器飞溅润滑内部流场分析［J］.润滑与密封,2017,42(8):131-134. SUN Kai,LIU Shaojun,HU Xiaozhou.Analysis on interal flow field of middle reducer splash lubrication based on dynamic mesh［J］.Lubrication of Engineering,2017,42(8):131-134.(in Chinese)
[15]	董春锋,林腾蛟,何泽银.基于动网格的齿轮箱内部流场数值模拟［J］.机械研究与应用,2011,24(2):17-22. DONG Chunfeng,LIN Tengjiao,HE Zeyin.Numerical simulation of flow field in the gearbox based on moving mesh［J］.Mechanical Research and Application,2011,24(2):17-22.(in Chinese)
[16]	刘杰,刘世军,徐文博,等.高速列车齿轮箱润滑性能优化与热平衡温度分析［J］.机械传动,2017,36(4):99-104. LIU Jie,LIU Shijun,XU Wenbo,et al.Lubricant performance optimization and thermal balance temperature analysis of high-speed train gearbox［J］.Journal of Mechanical Transmission,2017,36(4):99-104.(in Chinese)
[17]	ANDERSON J D.Computational fluid dynamics:the basics with applications［M］.Beijing：Tsinghua University Press,2002.
[18]	HIRT C W,NICHOLS B D.Volume of fluid (VOF) method for the dynamics of free boundaries［J］.Journal of Computational Physics,198l,39(1):201-225.
[19]	王福军.计算流体动力学分析［M］.北京:清华大学出版社,2017.
[20]	BARBER J R.The distribution of heat between sliding surfaces［J］.Journal Mechanical Engineering Science,1966,9(5):351-354.