双级轴向涡流器文氏管长度对流场和喷雾特性影响

刘冉; 罗莲军; 陈盛; 彭中九; 王志凯

doi:10.13224/j.cnki.jasp.2021.06.012

双级轴向涡流器文氏管长度对流场和喷雾特性影响

doi: 10.13224/j.cnki.jasp.2021.06.012

中国航空发动机集团有限公司湖南动力机械研究所,湖南株洲 412002

计量
- 文章访问数: 175
- HTML浏览量: 3
- PDF量: 177
- 被引次数: 0
出版历程
- 收稿日期: 2020-10-02
- 刊出日期: 2021-06-28

Effect of Venturi length on flow field and spray characterization of dual axial swirler

Hunan Aviation Powerplant Research Institute,Aero Engine Corporation of China,Zhuzhou Hunan 412002,China

摘要

摘要: 为了研究双级轴向涡流器文氏管长度对流场和喷雾特性的影响,通过数值计算和试验分别研究了4种文氏管长度的双级轴向涡流器方案的下游流场和匹配喷嘴的雾化特性。结果表明:随着文氏管无量纲长度由0.23增加至0.49,一级涡流器流量系数由0.98降至0.7,二级涡流器的流量系数保持0.75不变,涡流器出口旋流数由0.08增至0.48,旋流扩张角由闭合状态增至约90°,涡流器下游流场由反转回流区变为传统回流区。文氏管长度最短的方案的索太尔平均直径(SMD)和喷雾锥角受涡流器压降的影响较小,而其他方案的SMD和喷雾锥角受涡流器压降影响较大,且在相同涡流器压降和油压下,SMD和喷雾锥角随着文氏管长度增加而增大。
- 双级轴向涡流器 /
- 文氏管长度 /
- 流量系数 /
- 旋流数 /
- 喷雾特性
Abstract: In order to investigate the effect of dual axial swirler Venturi length on flow field and spray characteristics, the flow field downstream the dual axial swirler outlet for four different Venturi length dual axial swirlers was simulated and matched with fuel nozzle to test the spray characterization. The results showed that the 2ed swirler’s discharge coefficient was 0.75 constantly, while the 1st swirler’s discharge coefficient decreased from 0.98 to 0.7, the swirler outlet swirl number increased from 0.08 to 0.48, and the downstream flow field from inside-out recirculation zone turned into conventional recirculation zone as the dimensionless length of Venturi increased from 0.23 to 0.49. Spray cone angle and Sauter mean diameter (SMD) of shortness Venturi length case were less affected by air pressure drop across from swirler, however, the other cases’ spray cone angle and SMD were strongly affected by air pressure drop across from swirler, and SMD and spray cone angle increased as Venturi length increased under the same fuel mass flow rate and air pressure drop.
- dual axial swirler /
- Venturi length /
- discharge coefficient /
- swirl number /
- spray characterization

HTML

参考文献(33)

[1]	林左鸣.世界航空发动机手册［M］.北京:航空工业出版社,2012.
[2]	MONGIA H C.TAPS:a fourth generation propulsion combustor technology for low emissions［R］.AIAA-2003-2657,2003.
[3]	MONGIA H C.Engineering aspects of complex gas turbine combustion mixers:Part V 40 OPR(overall pressure ratio)［R］.AIAA-2011-5527,2011.
[4]	MONGIA H C.Future trends in commercial aviation engines’ combustion［C］∥Novel Combustion Concepts For Sustainable Energy Development.New Delhi:Springer,2014:113-176.
[5]	TACINA K M,CHANG C,HE Z J,et al.A second generation swirl-venturi lean direct injection combustion concept［R］.AIAA-2014-3434,2014.
[6]	HEATH C M.Characterization of swirl-venturi lean direct injection designs for aviation gas turbine combustion［J］.Journal of Propulsion and Power,2014,30(5):1334-1356.
[7]	REN X,XUE X,SUNG C J,et al.The impact of venturi geometry on reacting flows in a swirl-venturi lean direct injection airblast injector［R］.AIAA-2016-4650,2016.
[8]	张阳,邹建锋,郑耀,等.文氏管对旋流流场影响的数值研究［J］.推进技术,2016,37(5):907-915. ZHANG Yang,ZOU Jianfeng,ZHENG Yao,et al.Numerical simulation for effects of venturi tube on swirling flow field［J］.Journal of Propulsion Technology,2016,37(5):907-915.(in Chinese)
[9]	郑耀,张阳,邹建锋,等.文氏管喉部直径对燃烧室流场结构影响的数值模拟［J］.燃烧科学与技术,2015,21(2):97-102. ZHENG Yao,ZHANG Yang,ZOU Jianfeng,et al.Numerical simulation of effects of venturi tube throat diameter on flow field of combustor［J］.Journal of Combustion Science and Technology,2015,21(2):97-102.(in Chinese)
[10]	彭剑勇,李建中,郑剑文,等.文氏管长度对双级旋流杯出口流场影响的试验研究［J］.南京航空航天大学学报,2016,48(3):352-358. PENG Jianyong,LI Jianzhong,ZHENG Jianwen,et al.Experimental investigation on effect of venturi length on outlet flow field of double-stage swirler［J］.Journal of Nanjing University of Aeronautics and Astronautics,2016,48(3):352-358.(in Chinese)
[11]	ATESHKADI A,MCDONELL V G,SAMUELSEN G S.Effect of hardware geometry on gas and drop behavior in a radial mixer spray［J］.Symposium(International) on Combustion,1998,27(2):1985-1992.
[12]	ATESHKADI A,MCDONELL V G,SAMUELSEN G S.Effect of mixer geometry on fuel spray distribution,emission and stability［R］.AIAA-98-0247,1998.
[13]	MONGIA H C,GORE J P,GRINSTEIN F F,et al.Combustion research needs for helping development of next generation advanced combustors［R］.AIAA-2001-3853,2001.
[14]	MONGIA H C,AI-ROUB M,DANIS A,et al.Swirl cup modeling:Part Ⅰ［R］.AIAA-2001-3576,2001.
[15]	SUN H,CHUE T H,LAI M C,et al.Atomization and vaporization characteristics of airblast fuel injection inside a venturi tube［R］.AIAA-93-1766,1993.
[16]	徐华胜.高性能旋流燃烧装置气动和雾化特性研究［D］.成都:电子科技大学,2007. XU Huasheng.Study on aerodynamic and spray characterization of high performance airblast device［D］.Chengdu:University of Electronic Science and Technology of China,2007.(in Chinese)
[17]	BENSAADI M,DESAULTYD M A A,PITROU S P J,et al.Aerodynamic fuel injection system for a gas turbine engine:US6035645［P］.2000-03-14.
[18]	SANDELIS D J M.Device for injecting a mixture of air and fuel,and combustion chamber and turbomachine which are provided with such a device:US11/941551［P］.2008-07-17.
[19]	COMMARET P A,SANDELIS D J M.Device for injecting a mixture of air and fuel,and combustion chamber and turbomachine both equipped with such a device:US7861529［P］.2011-01-04.
[20]	康尧,林宇震,霍伟业,等.双级旋流杯结构变化对点火特性的影响研究［J］.推进技术,2014,35(5):675-680. KANG Yao,LIN Yuzhen,HUO Weiye,et al.Effects of hardware geometry of dual-stage swirl cup on ignition performance［J］.Journal of Propulsion Technology,2014,35(5):675-680.(in Chinese)
[21]	WANG Xiaofeng,LIN Yuzhen,HU Haosheng,et al.Effect of swirl cup’s venturi shape on spray structure and ignition process［R］.ASME Paper 2014-GT-25216,2014.
[22]	LIU Cunxi,LIU Fuqiang,YANG Jinhu,et al.Experimental investigation of spray and combustion performances of a fuel-staged low emission combustor:Part Ⅱ effects of venturi angle［R］.ASME Paper 2018-GT-76452,2018.
[23]	ATESHKADI A,MCDONELL V G,SAMUELSEN G S.Lean blowout model for a spray-fired swirl-stabilized combustor［J］.Proceedings of the Combustion Institute,2000,28(1):1281-1288.
[24]	航空工业部.高效节能发动机文集:第4分册燃烧室设计与试验［M］.北京:航空工业出版社,1991.
[25]	彭云晖,林宇震,许全宏,等.双旋流空气雾化喷嘴喷雾、流动和燃烧性能［J］.航空学报,2008,29(1):1-14. PENG Yunhui,LIN Yuzhen,XU Quanhong,et al.Atomization,aerodynamics and combustion performance of swirl cup［J］.Acta Aeronautica et Astronautica Sinica,2008,29(1):1-14.(in Chinese)
[26]	张弛,田兴鹏,林宇震,等.旋流杯文氏管长度对积碳的影响研究［J］.推进技术,2015,36(12):1833-1838. ZHANG Chi,TIAN Xingpeng,LIN Yuzhen,et al.Effects of Venturi length of swirl cup on carbon deposition［J］.Journal of Propulsion Technology,2015,36(12):1833-1838.(in Chinese)
[27]	LIN S C,WANG X,ESTEFANOS W,et al.The effect of the geometric modifications of the venturi on the non-reactive flow and combustion behavior using a counter-rotating radial-radial swirler［R］.ASME Paper 2017-GT-64876,2017.
[28]	WOLF P,STAFFELBACH G,ROUX A,et al.Massively parallel LES of azimuthal thermo-acoustic instabilities in annular gas turbines［J］.Combustion for Aerospace Propulsion,2009,337(6/7):385-394.
[29]	COHEN J M,ROSFJORD T J.Influence on the uniformity of sprays formed by high shear fuel nozzle/swirler assemblies［R］.AIAA-90-2193,1990.
[30]	曾青华,孔文俊.反向双旋涡流器受限火焰特性的流场分析［J］.航空动力学报,2016,31(12):2888-2894. ZENG Qinghua,KONG Wenjun.Flow field analysis for confined flames characteristics of counter dual-stage swirler［J］.Journal of Aerospace Power,2016,31(12):2888-2894.(in Chinese)
[31]	SHUNSAKUS O,MASANAO I,MAI T,et al.Low-NOx combustion of fuel spray-air mixtures from a converging splitter in a co-swirling annular air flow［R］.ASME Paper 2017-GT-65205,2017.
[32]	LEFEBVRE A H,BALLAL D R.Gas turbine combustion:alternative fuels and emissions［M］.Boca Raton,USA:Taylor and Francis Press,2010.
[33]	胡正义.航空发动机设计手册:第9册主燃烧室［M］.北京:航空工业出版社,2000.