双下侧布局带泄流腔二元进气道试验
DOI:
CSTR:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Investigation of two-dimensional supersonic twin inlet with slot-coupled cavity in 90° configuration at venter
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对一种双下侧布局带泄流腔的二元进气道进行了试验研究.试验时,来流速度范围Ma=2.0~3.5,姿态角范围为α=-4°~10°,β=0°~4°.试验获得了进气道的反压特性曲线、速度特性曲线、迎角特性曲线和侧滑角特性曲线.分析表明,随着来流速度和迎角的增加,进气道的流量系数先增加,在设计点达到最大,之后由于弹身头部激波的影响略有减小.侧滑时两侧进气道气流状态不同,工作范围由性能较低的迎风侧进气道来决定.另外,通过分析进气道的沿程静压分布曲线,说明泄流腔结构能使结尾激波停留在泄流腔边缘,扩大了进气道的工作范围.

    Abstract:

    A two-dimensional mixed-compression inlet model with slot-coupled cavity in 90° configuration at venter was investigated by wind tunnel at Mach number from 2.0 to 3.5.The range of the investigation covers angle of attack from-4° to 10° and angle of yaw from 0 to 4°.The performances,including critical pressure,total pressure recovery coefficient and mass flow ratio,were acquired.The results indicate that:with increase of the free stream Mach number or the angle of attack at Ma=3.0,the mass flow ratio increases firstly and then declines a little due to the increase of the total pressure loss around the body nose;and the maximum is obtained at design point.The flow field of two inlets is different at yaw,and the work range is determined by the windward inlet.Besides,the distribution of static-pressure coefficient along the duct validates that a terminal shock can stay around the cavity,so inlets with the slot-coupled cavity can work under wider back pressure.

    参考文献
    相似文献
    引证文献
引用本文

麻肖妃,谢旅荣,郭荣伟.双下侧布局带泄流腔二元进气道试验[J].航空动力学报,2010,25(8):1818~1824. MA Xiao-fei, XIE Lü-rong, GUO Rong-wei. Investigation of two-dimensional supersonic twin inlet with slot-coupled cavity in 90° configuration at venter[J]. Journal Of Aerospace Power,2010,25(8):1818-1824.

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2009-07-07
  • 最后修改日期:2009-11-30
  • 录用日期:
  • 在线发布日期:
  • 出版日期:
文章二维码
您是第位访问者
中文版 ® 2025 版权所有
技术支持:北京勤云科技发展有限公司