Volume 36 Issue 11
Nov.  2021
Turn off MathJax
Article Contents
Article Navigation >  Journal of Aerospace Power  > 2021  >  36(11): 2363-2371
ZHOU Zihe, SU Hao, HE Fei, WANG Jianhua. Numerical analysis on cooling capacity of transpiration cooling system[J]. Journal of Aerospace Power, 2021, 36(11): 2363-2371. doi: 10.13224/j.cnki.jasp.20200544
Citation: ZHOU Zihe, SU Hao, HE Fei, WANG Jianhua. Numerical analysis on cooling capacity of transpiration cooling system[J]. Journal of Aerospace Power, 2021, 36(11): 2363-2371. doi: 10.13224/j.cnki.jasp.20200544
shu

Numerical analysis on cooling capacity of transpiration cooling system

doi: 10.13224/j.cnki.jasp.20200544

  • Department of Thermal Science and Energy Engineering， School of Engineering Science， University of Science and Technology of China，Hefei 230027，China

  • Received Date: 2020-12-21
  • Publish Date: 2021-11-28
    Abstract
  • The maximum heat flux that the system can withstand under a specific amount of coolant consumption，was numerically investigated.The strict theoretical analysis and simulation results indicated that the transpiration cooling capacity was restricted by the coolant heat absorption capacity of the coolant and the heat exchange capacity between the fluid and solid.Under a small coolant mass flux，the transpiration cooling capacity was mainly determined by the coolant heat absorption capacity，while the effect of the heat exchange capacity between the fluid and solid on the transpiration cooling capacity increased with the coolant mass flux.Due to this crucial change，the effects of solid thermal conductivity，particle diameter of porous media and coolant specific heat on the transpiration cooling capacity under a small coolant mass flux were quite different with those under a larger coolant mass flux.

     

    • FullText(HTML)
  • loading
    • References(22)
  • [1]
    KARIMI M S,OBOODI M J.Investigation and recent developments in aerodynamic heating and drag reduction for hypersonic flows[J].Heat and Mass Transfer/Waerme-Und Stoffuebertragung,2019,55（2）：547-569.
    [2]
    JIANG Yuguang,QIN Jiang,CHETEHOUNA K,et al.Effect of geometry parameters on the hydrocarbon fuel flow rate distribution in pyrolysis zone of SC ramjet cooling channels[J].International Journal of Heat and Mass Transfer,2019,141（6）：1114-1130.
    [3]
    ZHU Yinhai,PENG Wei,XU Ruina,et al.Review on active thermal protection and its heat transfer for airbreathing hypersonic vehicles[J].Chinese Journal of Aeronautics,2018,31（10）：1929-1953.
    [4]
    SHEN Binxian,YIN Liang,LIU Hongpeng,et al.Thermal protection characteristics for a combinational opposing jet and platelet transpiration cooling nose-tip[J].Acta Astronautica,2019,155：143-152.
    [5]
    XIAO Xuefeng,ZHAO Guangbo,ZHOU Weixing,et al.Large-eddy simulation of transpiration cooling in turbulent channel with porous wall[J].Applied Thermal Engineering,2018,145：618-629.
    [6]
    LEONTIEV A,SAVELIEV A,KICHATOV B,et al.Effect of gaseous coolant temperature on the transpiration cooling for porous wall in the supersonic flow[J].International Journal of Heat and Mass Transfer,2019,142：118433.1-118433.9.
    [7]
    YANG Li,MIN Zheng,YUE Tianwei,et al.High resolution cooling effectiveness reconstruction of transpiration cooling using convolution modeling method[J].International Journal of Heat and Mass Transfer,2019,133：1134-1144.
    [8]
    SU Hao,WANG Jianhua,HE Fei,et al.Numerical investigation on transpiration cooling with coolant phase change under hypersonic conditions[J].International Journal of Heat and Mass Transfer,2019,129：480-490.
    [9]
    JIANG Peixue,LIAO Zhiyuan,HUANG Zheng,et al.Influence of shock waves on supersonic transpiration cooling[J].International Journal of Heat and Mass Transfer,2019,129：965-974.
    [10]
    LANGENER T,JVON WOLFERSDORF,SELZER M,et al.Experimental investigations of transpiration cooling applied to C/C material[J].International Journal of Thermal Sciences,2012,54：70-81.
    [11]
    YANG Li,CHEN Wei,CHYU M K.A convolution modeling method for pore plugging impact on transpiration cooling configurations perforated by straight holes[J].International Journal of Heat and Mass Transfer,2018,126：1057-1066.
    [12]
    HUANG Gan,MIN Zheng,YANG Li,et al.Transpiration cooling for additive manufactured porous plates with partition walls[J].International Journal of Heat and Mass Transfer,2018,124：1076-1087.
    [13]
    HUANG Gan,ZHU Yinhai,LIAO Zhiyuan,et al.Transpiration cooling with bio-inspired structured surfaces[J].Bioinspiration and Biomimetics,2020,15（3）：036016.1-036016.21.
    [14]
    LIU Yuanqing,JIANG Peixue,XIONG Yanbin,et al.Experimental and numerical investigation of transpiration cooling for sintered porous flat plates[J].Applied Thermal Engineering,2013,50（1）：997-1007.
    [15]
    OTSU H,FUJITA K,ITO T.Application of the transpiration cooling method for reentry vehicles[C].Reno,Nevada,US：the 45th AIAA Aerospace Sciences Meeting,2007.
    [16]
    ARAI M,SUIDZU T.Porous ceramic coating for transpiration cooling of gas turbine blade[J].Journal of Thermal Spray Technology,2013,22（5）：690-698.
    [17]
    LIU Yuanqing,JIANG Peixue,JIN Shaoshan,et al.Transpiration cooling of a nose cone by various foreign gases[J].International Journal of Heat and Mass Transfer,2010,53（23/24）：5364-5372.
    [18]
    KUHN M,HALD H.Application of transpiration cooling for hot structures[C]∥RESPACE-Key Technologies for Reusable Space Systems.Berlin Heidelberg:Springer,2008：82-103.
    [19]
    HUANG Zheng,ZHU Yinhai,XIONG Yanbin,et al.Investigation of transpiration cooling for sintered metal porous struts in supersonic flow[J].Applied Thermal Engineering,2014,70（1）：240-249.
    [20]
    CHEURET F,STEELANT J,LANGENER T.Numerical investigations on transpiration cooling for scramjet applications using different coolants[R].San Francisco,US：the 17th AIAA International Space Planes and Hypersonic Systems and Technologies Conference,2011.
    [21]
    BURKE S P,PLUMMER W B. Gas flow through packed columns[J].Industrial and Engineering Chemistry,1928,20（11）：1196-1200.
    [22]
    LIU Yuanqing,XIONG Yanbin,JIANG Peixue,et al.Effects of local geometry and boundary condition variations on transpiration cooling[J].International Journal of Heat and Mass Transfer,2013,62（1）：362-372.
    • Relative Articles
    • Supplements(0)
    • Cited By
  • 加载中

Catalog

    通讯作者: 陈斌, bchen63@163.com
    • 1. 

      沈阳化工大学材料科学与工程学院 沈阳 110142

    1. 本站搜索
    2. 百度学术搜索
    3. 万方数据库搜索
    4. CNKI搜索
    Get Citation
    PDF(3631.0KB)
    XML

    Article Metrics

    Article views (459) PDF downloads(124) Cited by()
    Proportional views
    Related

    Copyright © 《Journal of Aerospace Power》 All Rights Reserved.

    Supported by: Beijing Renhe Information Technology Co., Ltd.  

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return