| Citation: | ZHANG Xingyuan, AI Yanting, TIAN Jinhu, et al. Analysis and design study on the structural performance of new flow tube grate tooth seal for high altitude table[J]. Journal of Aerospace Power, 2025, 40（10）：20230653 doi: 10.13224/j.cnki.jasp.20230653
|
A new flow tube grate tooth sealing structure model of high-altitude table was built based on the heat-fluid-solid coupling method. Simulation and experimental studies of the sealing characteristics were carried out. The influence of the design gap on the sealing performance and contact wear of grate teeth was revealed. The gap was optimized by response surface methodology. Finally, the structural performance before and after optimization was analyzed comparatively. The study showed that the error between the simulation and experimental results of the leakage volume did not exceed 9.2%. Taking the remaining clearance not exceeding 0.1 mm as the optimization condition, the front-end design clearance of 1.9 mm was obtained, the seal design clearance was 0.75 mm, and the back-end design clearance was 2.1 mm. After optimization, the leakage of grate tooth seal structure was
| [1] |
侯敏杰, 刘冬根. 航空发动机高空台的发展与展望[J]. 航空科学技术, 2012, 23(3): 1-4. HOU Minjie, LIU Donggen. Development and prospect of the aero-engine altitude test facility[J]. Aeronautical Science & Technology, 2012, 23(3): 1-4. (in Chinese doi: 10.3969/j.issn.1007-5453.2012.03.001
HOU Minjie, LIU Donggen. Development and prospect of the aero-engine altitude test facility[J]. Aeronautical Science & Technology, 2012, 23(3): 1-4. (in Chinese) doi: 10.3969/j.issn.1007-5453.2012.03.001
|
| [2] |
纪国剑. 航空发动机典型篦齿封严泄漏特性的数值和实验研究[D]. 南京: 南京航空航天大学, 2008. JI Guojian. Numerical and experimental investigation of sealing characteristics on typical labyrinth seals in aero-engine[D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2008. (in Chinese
JI Guojian. Numerical and experimental investigation of sealing characteristics on typical labyrinth seals in aero-engine[D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2008. (in Chinese)
|
| [3] |
BRUCE RALPHIN ROSE J, JINU G R, BRINDHA C J. A numerical optimization of high altitude testing facility for wind tunnel experiments[J]. Chinese Journal of Aeronautics, 2015, 28(3): 636-648. doi: 10.1016/j.cja.2015.04.018
|
| [4] |
王曦, 朱美印, 张松, 等. 国外高空模拟试车台控制系统技术发展[J]. 燃气涡轮试验与研究, 2017, 30(6): 49-55. WANG Xi, ZHU Meiyin, ZHANG Song, et al. Technology development of foreign altitude simulation test facilities control system[J]. Gas Turbine Experiment and Research, 2017, 30(6): 49-55. (in Chinese doi: 10.3969/j.issn.1672-2620.2017.06.010
WANG Xi, ZHU Meiyin, ZHANG Song, et al. Technology development of foreign altitude simulation test facilities control system[J]. Gas Turbine Experiment and Research, 2017, 30(6): 49-55. (in Chinese) doi: 10.3969/j.issn.1672-2620.2017.06.010
|
| [5] |
侯敏杰, 陈建民, 徐国, 等. 先进航空动力崛起的基石: 高空台[C]//大型飞机关键技术高层论坛暨中国航空学会2007年学术年会论文集. 深圳: 中国航空学会, 2007: 906-910. HOU Minjie, CHEN Jianmin, XU Guo, et al. Altitude test facility: the cornerstone for the rise of advanced aero-propulsion [C]//Proceedings of the High-Level Forum on Key Technologies for Large Aircraft and the 2007 Annual Conference of the Chinese Society of Aeronautics and Astronautics. Shenzhen: Chinese Journal of Aeronautics, 2007: 906-910.
HOU Minjie, CHEN Jianmin, XU Guo, et al. Altitude test facility: the cornerstone for the rise of advanced aero-propulsion [C]//Proceedings of the High-Level Forum on Key Technologies for Large Aircraft and the 2007 Annual Conference of the Chinese Society of Aeronautics and Astronautics. Shenzhen: Chinese Journal of Aeronautics, 2007: 906-910.
|
| [6] |
闫玉涛, 马洪旺, 张立静, 等. 基于遗传算法圆周密封结构多目标优化[J]. 推进技术, 2023, 44(9): 2206064. YAN Yutao, MA Hongwang, ZHANG Lijing, et al. Multi-objective optimization of circumferential seal structure based on genetic algorithm[J]. Journal of Propulsion Technology, 2023, 44(9): 2206064. (in Chinese
YAN Yutao, MA Hongwang, ZHANG Lijing, et al. Multi-objective optimization of circumferential seal structure based on genetic algorithm[J]. Journal of Propulsion Technology, 2023, 44(9): 2206064. (in Chinese)
|
| [7] |
张雨, 张开林. 结构变形对高速齿轮箱直通式迷宫密封性能的影响分析[J]. 液压与气动, 2019, 43(3): 14-18. ZHANG Yu, ZHANG Kailin. Influence of structural deformation on sealing performance of high-speed gearbox with straight-through labyrinth seal[J]. Chinese Hydraulics & Pneumatics, 2019, 43(3): 14-18. (in Chinese doi: 10.11832/j.issn.1000-4858.2019.03.003
ZHANG Yu, ZHANG Kailin. Influence of structural deformation on sealing performance of high-speed gearbox with straight-through labyrinth seal[J]. Chinese Hydraulics & Pneumatics, 2019, 43(3): 14-18. (in Chinese) doi: 10.11832/j.issn.1000-4858.2019.03.003
|
| [8] |
LIAO Chuanjun, HUANG Weifeng, SUO Shuangfu, et al. Fluid-solid strong-interaction model of mechanical seals in reactor coolant pumps[J]. Science China Technological Sciences, 2011, 54(9): 2339-2348. doi: 10.1007/s11431-011-4427-8
|
| [9] |
WANG Qiang, HU Yaping, JI Honghu. Leakage, heat transfer and thermal deformation analysis method for contacting finger seals based on coupled porous media and real structure models[J]. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2020, 234(10): 2077-2093. doi: 10.1177/0954406219900219
|
| [10] |
LI Xinyang, YANG Jiangang, XU Wanjun. Research and comparison on the leakage and fluid force between the axial and the radial labyrinth seal[J]. Journal of Mechanical Science and Technology, 2015, 29(11): 4611-4620. doi: 10.1007/s12206-015-1006-0
|
| [11] |
ZHANG Guanghui, WANG Guilong, LIU Zhansheng, et al. Stability characteristics of steam turbine rotor seal system with analytical floating ring seal force model[C]//Turbo Expo: Power for Land, Sea, and Air. American Society of Mechanical Engineers. San Antonio, Texas, US: International Gas Turbine Institute, 2013, 55270: V07BT30A004.
|
| [12] |
孙丹, 周敏, 赵欢, 等. 考虑齿变形的迷宫密封泄漏特性流固耦合数值研究[J]. 润滑与密封, 2021, 46(3): 130-136. SUN Dan, ZHOU Min, ZHAO Huan, et al. Numerical study on fluid-structure interaction of labyrinth seal leakage characteristics considering tooth deformation[J]. Lubrication Engineering, 2021, 46(3): 130-136. (in Chinese doi: 10.3969/j.issn.0254-0150.2021.03.021
SUN Dan, ZHOU Min, ZHAO Huan, et al. Numerical study on fluid-structure interaction of labyrinth seal leakage characteristics considering tooth deformation[J]. Lubrication Engineering, 2021, 46(3): 130-136. (in Chinese) doi: 10.3969/j.issn.0254-0150.2021.03.021
|
| [13] |
陈汇龙, 李同, 赵斌娟, 等. 动压型机械密封内流场及性能的流固热耦合[J]. 排灌机械工程学报, 2017, 35(6): 502-507. CHEN Huilong, LI Tong, ZHAO Binjuan, et al. Analysis of flow field and performances in hydrodynamic mechanical seal based on fluid-solid-heat interaction[J]. Journal of Drainage and Irrigation Machinery Engineering, 2017, 35(6): 502-507. (in Chinese doi: 10.3969/j.issn.1674-8530.16.0162
CHEN Huilong, LI Tong, ZHAO Binjuan, et al. Analysis of flow field and performances in hydrodynamic mechanical seal based on fluid-solid-heat interaction[J]. Journal of Drainage and Irrigation Machinery Engineering, 2017, 35(6): 502-507. (in Chinese) doi: 10.3969/j.issn.1674-8530.16.0162
|
| [14] |
周敏, 孙丹, 赵欢, 等. 基于流固热耦合的非金属迷宫密封泄漏特性与公式构造[J]. 航空动力学报, 2021, 36(8): 1783-1792. ZHOU Min, SUN Dan, ZHAO Huan, et al. Leakage characteristics and formula establishment of nonmetallic labyrinth seal based on fluid-solid-thermal coupling[J]. Journal of Aerospace Power, 2021, 36(8): 1783-1792. (in Chinese
ZHOU Min, SUN Dan, ZHAO Huan, et al. Leakage characteristics and formula establishment of nonmetallic labyrinth seal based on fluid-solid-thermal coupling[J]. Journal of Aerospace Power, 2021, 36(8): 1783-1792. (in Chinese)
|
| [15] |
吴丁毅. 直通式篦齿密封内部流场显示研究[J]. 流体机械, 1997, 25(2): 11-14, 35. WU Dingyi. Research on the Internal Flow Field Display of Direct-Through Toothed Sealing[J]. Fluid Machinery, 1997, 25(2): 11-14, 35. (in Chinese
WU Dingyi. Research on the Internal Flow Field Display of Direct-Through Toothed Sealing[J]. Fluid Machinery, 1997, 25(2): 11-14, 35. (in Chinese)
|
| [16] |
杨志明, 艾延廷, 苏金友, 等. 高空台动静架连接新型篦齿密封结构封严特性研究[J]. 推进技术, 2022, 43(8): 210206. YANG Zhiming, AI Yanting, SU Jinyou, et al. Sealing characteristics study on new labyrinth seal structure of dynamic and static frame connection of altitude simulation test facility[J]. Journal of Propulsion Technology, 2022, 43(8): 210206. (in Chinese
YANG Zhiming, AI Yanting, SU Jinyou, et al. Sealing characteristics study on new labyrinth seal structure of dynamic and static frame connection of altitude simulation test facility[J]. Journal of Propulsion Technology, 2022, 43(8): 210206. (in Chinese)
|
| [17] |
邹宜霖, 艾延廷, 苏金友. 高空模拟试车台动静架新型篦齿密封结构研究[J]. 燃气涡轮试验与研究, 2020, 33(3): 57-62. ZOU Yilin, AI Yanting, SU Jinyou. Study on a new labyrinth seal structure of dynamic and static bench of the altitude simulation test facility[J]. Gas Turbine Experiment and Research, 2020, 33(3): 57-62. (in Chinese
ZOU Yilin, AI Yanting, SU Jinyou. Study on a new labyrinth seal structure of dynamic and static bench of the altitude simulation test facility[J]. Gas Turbine Experiment and Research, 2020, 33(3): 57-62. (in Chinese)
|
| [18] |
纪国剑, 吉洪湖. 直通篦齿静止衬套上磨损槽对泄漏特性影响的数值研究[J]. 航空动力学报, 2008, 23(8): 1403-1408. JI Guojian, JI Honghu. Numerical investigation of effect of static bush with rub-grooves on the straight-through labyrinth seal leakage[J]. Journal of Aerospace Power, 2008, 23(8): 1403-1408. (in Chinese
JI Guojian, JI Honghu. Numerical investigation of effect of static bush with rub-grooves on the straight-through labyrinth seal leakage[J]. Journal of Aerospace Power, 2008, 23(8): 1403-1408. (in Chinese)
|
| [19] |
RHODE D L, HIBBS R I. Clearance effects on corresponding annular and labyrinth seal flow leakage characteristics[J]. Journal of Tribology, 1993, 115(4): 699-704. doi: 10.1115/1.2921696
|
| [20] |
DENECKE J, SCHRAMM V, KIM S, et al. Influence of rub-grooves on labyrinth seal leakage[J]. Journal of Turbomachinery, 2003, 125(2): 387-393. doi: 10.1115/1.1539516
|
| [21] |
艾延廷, 刘海月, 田晶, 等. 薄壁机匣螺栓连接结构多目标优化设计[J]. 推进技术, 2019, 40(4): 876-883. AI Yanting, LIU Haiyue, TIAN Jing, et al. Multi-objective optimization design of bolt connected flange for thin-walled casing[J]. Journal of Propulsion Technology, 2019, 40(4): 876-883. (in Chinese
AI Yanting, LIU Haiyue, TIAN Jing, et al. Multi-objective optimization design of bolt connected flange for thin-walled casing[J]. Journal of Propulsion Technology, 2019, 40(4): 876-883. (in Chinese)
|
| [22] |
胡东旭, 贾力, 杨立新. 篦齿封严泄漏特性的实验[J]. 航空动力学报, 2014, 29(3): 549-555. HU Dongxu, JIA Li, YANG Lixin. Experiment on leakage characteristics in labyrinth seal[J]. Journal of Aerospace Power, 2014, 29(3): 549-555. (in Chinese
HU Dongxu, JIA Li, YANG Lixin. Experiment on leakage characteristics in labyrinth seal[J]. Journal of Aerospace Power, 2014, 29(3): 549-555. (in Chinese)
|
DownLoad:
