| Citation: | ZHAO Bin, LI Shao-bin, LI Qiu-shi, ZHOU Sheng. Numerical research on enhancing the axial compressor performance by bleeding[J]. Journal of Aerospace Power, 2011, 26(2): 262-271.
|
| [1] |
杨燕生,吴向宇,陆海鹰,等.航空发动机设计手册,第16分册:空气系统及传热分析[M].北京:航空工业出版社,2001.
|
| [2] |
林左鸣.战斗机发动机的研制现状和发展趋势[J].航空发动机,2006,32(1):1-8. LIN Zuoming.The current development and future trends of fighter engines[J].Journal of Aeroengine,2006,32(1):1-8.(in Chinese)
|
| [3] |
张津,洪杰,陈光.现代航空发动机技术与发展[M].北京:北京航空航天大学出版社,2006.
|
| [4] |
唐智明,詹孟宣.高效节能发动机文集:第三分册[M].北京:航空工业出版社,1991.
|
| [5] |
赵斌,李绍斌,侯安平,等.发动机空气系统气源引气的研究和探讨 //航空学会第十五届叶轮机专业委员会学术交流会文集.张家界:中国航空学会动力专业分会,2009:190-198.
|
| [6] |
Wellborn S R,Michael L K.Bleed flow interactions with an axial-flow compressor powerstream .AIAA Paper 2002-4057,2002.
|
| [7] |
Gummer V,Goller M,Swoboda M.Numerical investigation of end wall boundary layer removal on highly loaded axial compressor blade rows [J].Journal of Turbomachinery,2008,130:011015-1-9.
|
| [8] |
Kerrcbroek J L,Reijnan D P,Ziminsky W S,et al.Aspirated compressors .ASME Paper GT-97-525,1997.
|
| [9] |
Merchant A A,Drela M,Kerrebrock J L,et al.Aerodynamic design and analysis of a high pressure ratio aspirated compressor stage .ASME Paper GT-2000-619,2000.
|
| [10] |
Schuler B J,Kerrebrock J L,Merchant A A,et al.Design,analysis,fabrication and test of an aspirated fan stage .ASME Paper GT 2000-618,2000.
|
| [11] |
周海,李秋实,陆亚钧.跨音风扇转子叶片抽吸气数值试验探索[J].航空动力学报,2004,19(3):408-412. ZHOU Hai,LI Qiushi,LU Yajun.Prospects of numerical analysis of an aspirated transonic fan rotor[J].Journal of Aerospace Power,2004,19(3):408-412.(in Chinese)
|
| [12] |
王松涛,潜纪儒,冯国泰,等.壁面吸气抑制分离减少流动损失的研究[J].工程热物理学报,2006,27(1):48-50. WANG Songtao,QIAN Jiru,FENG Guotai,et al.The research about loss reduction and separation suppress by wall suction[J].Journal of Engineering Thermophysics,2006,27(1):48-50.(in Chinese)
|
| [13] |
Conan F,Savarese S,Moteurs S.Bleed airflow CFD modeling in areodynamics simulations of jet engine compressors .ASME Paper GT 2001-0544,2001.
|
| [14] |
Saathoff H,Stark U.Tip clearance flow in a low speed compressor and cascade .Firenze,Italy:Fourth European Conference on Turbomachinery,2001.
|
| [15] |
Gummer V,Swoboda M,Goller M,et al.The impact of rotor tip sweep on the three-dimensional flow in a highly-loaded single stage low-speed axial compressor:Part 1—Design and numerical analysis .Prague Czech Republic:Fifth European Conference on Turbomachinery,2003.
|
| [16] |
Joslyn H D,Dring R P.Axial compressor stator aerodynamics [J].ASME Journal of Heat Transfer,1985,107(2):485-493.
|
| [17] |
Kang S,Hirsch C.Three dimensional flow in a linear compressor cascade at design condition .ASME Paper GT 91-114,1991.
|
| [18] |
李志平,李秋实,袁巍,等.轴流压气机气动扩稳一类新措施的实验探索[J].航空动力学报,2006,21(3):485-491. LI Zhiping,LI Qiushi,YUAN Wei,et al.The experimental research on a new method for extending the axial-compressors stall margin[J].Journal of Aerospace Power,2006,21(3):485-491.(in Chinese)
|
| [19] |
李志平.轴流压气机实现非定常耦合流型的实验研究 .北京:北京航空航天大学,2006. LI Zhiping.Experimental investigation of realizing unsteady cooperative flow type in axial-flow compressor .Beijing:Beijing University of Aeronautics and Astronautics,2006.(in Chinese)
|
| [20] |
Hall E J,Crook A J,Delancy R A.Aerodynamic analysis of compressor casing treatment with a 3-D Navier-Stokes solver .AIAA Paper 94-2796,1994.
|
| [21] |
Yang H,Nuernberger D,Nicke E A.Numerical investigation of casing treatment mechanisms with a conservative mix-cell approach .ASME Paper GT 2003-28483,2003.
|
DownLoad: