| Citation: | NING Fang-fei, FAN Lin. Quasi-steady flow model of slot-type casing treatments Ⅰ: modeling method and validation[J]. Journal of Aerospace Power, 2012, 27(6): 1261-1269.
|
| [1] |
Prince D C,Jr.,Wisler D C,Hilvers D E.A study of casing treatment stall margin improvement phenomena .NASA-CR-134552,1974.
|
| [2] |
Takata H,Tsukuda Y.Stall margin improvement by casing treatment:its mechanism and effectiveness[J].Journal of Engineering for Power,1977,99(1):121-133.
|
| [3] |
Fujita H,Takata H.A study of configurations of casing treatment for axial flow compressors[J].Bulletin of the JSME,1984,27(230):1675-1681.
|
| [4] |
Smith G D J,Cumpsty N A.Flow phenomena in compressor casing treatment[J].ASME Journal of Engineering for as Turbines and Power,1984,106(3):532-541.
|
| [5] |
Cheng P,Prell M E,Greitzer E M,et al.Effects of compressor hub treatment on stator stall margin and performance[J].Journal of Aircraft,1984,21(7):469-475.
|
| [6] |
庄平,陆亚钧.机匣处理对压气机性能和气流结构影响的试验研究[J].航空学报,1986,7(4):363-370. ZHUANG Ping,LU Yajun.The effect of casing treatment on the performance and flowfield in axial compressors[J].Acta Aeronautica et Astronautica Sinica,1986,7(4):363-370.(in Chinese)
|
| [7] |
Lee N K W,Greitzer E M,Effects of endwall suction and blowing on compressor stability enhancement[J].Journal of Turbomachinery,1990,112(1):133-144.
|
| [8] |
Hall E J,Heidegger N J,Delaney R A.Performance prediction of endwall treated fan rotors with inflow distortion .AIAA-1996-244,1996.
|
| [9] |
Yang H,Nuernberger D,Nicke E,et al.Numerical investigation of casing treatment mechanisms with a conservative mixed-cell approach .ASME Paper GT-2003-38483,2003.
|
| [10] |
Wilke I,Kau H P.A numerical investigation of the flow mechanisms in a high pressure compressor front stage with axial slots[J].Journal of Turbomachinery,2004,126(3):339-349.
|
| [11] |
Crook A J.Numerical investigation of endwall casing treatment flow phenomena .GTL Report No.200,1989.
|
| [12] |
Hall E J,Crook A J,Delaney R A.Aerodynamic analysis of compressor casing treatment with a 3-D Navier-Stokes solver .AIAA Paper 94-2796,1994.
|
| [13] |
Wilke I,Kau H P.A numerical investigation of the influence of casing treatments on the tip leakage flow in a hpc front stage .ASME Paper GT-2002-30642,2002.
|
| [14] |
NING Fangfei,XU Liping.Aerodynamics of compressor casing treatment PartⅡ:a quasi-steady model for casing treatment flows .ASME Paper GT2008-51542,2008.
|
| [15] |
Denton J D.Loss mechanisms in turbomachines[J].Journal of Turbomachinery,1993,115(4):621-656.
|
| [16] |
宁方飞.考虑真实几何复杂性的跨声压气机内部流动的数值模拟 .北京: 北京航空航天大学,2002. NING Fangfei.Numerical simulation of the transonic compressor inner flow considering real geometrical complexity .Beijing:Beijing University of Astronautics and Aeronautics,2002.(in Chinese)
|
| [17] |
Edwards J R.A low-diffusion flux-splitting scheme for navier-stokes calculations[J].Computer & Fluids,1997,26(6):635-659.
|
| [18] |
NING Fangfei,XU Liping.Numerical investigation of transonic compressor rotor flow using an implicit 3d flow solver with one-equation Spalart-Allmaras turbulence model .ASME Paper 2001-GT-0359,2001.
|
| [19] |
Jameson A.Time dependent calculation using multigrid with applications to unsteady flows past airfoils and wings .AIAA Paper 91-1596,1991.
|
| [20] |
NING Fangfei,XU Liping.A solver using newton's method for unsteady viscous flows[J].Acta Mechanica Sinica,2003,19(3):220-227.
|
DownLoad: