| Citation: | DENG Xiao-zhong, XU Ai-jun, ZHANG Jing, LI Ju-bo, YANG Jian-jun. Effect of meshed pitch deviation on transmission error in hypoid gears[J]. Journal of Aerospace Power, 2013, 28(3): 597-602.
|
| [1] |
邓效忠,方宗德,杨宏斌,等.高重合度弧齿锥齿轮的强度分析[J].航空动力学报,2002,17(3):367-372.DENG Xiaozhong,FANG Zongde,YANG Hongbing,et al.Strength analysis of spiral bevel gears with high contact ratio[J].Journal of Aerospace Power,2002,17(3): 367-372.(in Chinese)
|
| [2] |
Smith J D.Gear noise and vibration[M].2nd ed.New York:Marcel Dekker Inc.,2003.
|
| [3] |
邓效忠,方宗德,魏冰阳,等.高重合度弧齿锥齿轮加工参数设计与重合度测定[J].机械工程学报,2004,40(6):95-99.DENG Xiaozhong,FANG Zongde,WEI Bingyang,et al.Design and experiment of spiral bevel gears with high contact ratio [J].Chinese Journal of Mechanical Engineering,2004,40(6):95-99.(in Chinese)
|
| [4] |
杨建军,邓效忠,魏冰阳,等.弧齿锥齿轮激励研齿的动态研磨分析与试验[J].航空动力学报,2010,25(12):2839-2845.YANG Jianjun,DENG Xiaozhong,WEI Bingyang,et al.Study and experiments of dynamic mechanism of excited gear lapping of spiral bevel gear[J].Journal of Aerospace Power,2010,25(12):2839-2845.(in Chinese)
|
| [5] |
石照耀,张旭.齿轮单面啮合测量技术的发展及其应用[J].工具技术,2008,42(3):10-15.SHI Zhaoyao,ZHANG Xu.Development and application of gear single-flank testing technology[J].Tool Engineering,2008,42(3):10-15.(in Chinese)
|
| [6] |
徐爱军,邓效忠,徐恺,等.基于时钟细分法的弧齿锥齿轮传动误差测量研究[J].机械传动,2012(8):1-5.XU Aijun,DENG Xiaozhong,XU Kai,et al.The research of the transmission error measurement of spiral bevel and hypoid gears based on the clock subdivision[J].Journal of Mechanical Transmission,2012(8):1-5.(in Chinese)
|
| [7] |
Litvin F L.Gear geometry and applied theory[M].Englewood Cliffs,NJ:Prentice Hall,1994.
|
| [8] |
Michael F P.Troubleshooting gear noise[J].Gear Solutions,2011(1):39-44.
|
| [9] |
AGMA.ANSI/AGMA 2009-B01 Bevel gear classification tolerances,and measuring methods[S].Alexanria,Virginia,USA:AGMA,2001.
|
| [10] |
邓效忠,方宗德,任东锋,等.弧齿锥齿轮的齿距误差对传动性能的影响研究[J].航空动力学报,2002,17(2):268-271.DENG XiaoZhong,FANG Zongde,REN Dongfeng,et al.Study on contact ratio of spiral bevel gears and influence of pitch error[J].Journal of Aerospace Power,2002,17(2): 268-271.(in Chinese)
|
| [11] |
周彦伟,邓效忠,方宗德,等.齿距误差对弧齿锥齿轮齿间载荷分配和强度的影响[J].中国机械工程,2002,13(7):1518-1520.ZHOU Yanwei,DENG Xiaozhong,FANG Zongde,et al.Influence of pitch error on load share between teeth and bending strength of spiral bevel gears[J].China Mechanical Engineering,2002,13(7):1518-1520.(in Chinese)
|
| [12] |
XU Aijun,DENG Xiaozhong,ZHANG Jing,et al.Design of multichannel card oriented to hypoid gear measurement [J].CSSS US:IEEE Computer Society,2011(4):3164-3167.
|
| [13] |
XU Aijun,DENG Xiaozhong,ZHANG Jing,et al.A new numerical algorithm for transmission error measurement at gears meshing [R].Germany: Trans Tech Publications,2012.
|
| [14] |
Gosselin C,Guertin T,Bremond D,et al.Simulation and experimental measurement of the transmission error of real hypoid gears under load[J].Journal of Mechanical Design,2000,3(122):109-122.
|
| [15] |
李天兴,邓效忠,李聚波,等.螺旋锥齿轮齿面误差分析与自动反馈修正[J].航空动力学报,2011,26(5):1194-1200.LI Tianxing,DENG Xiaozhong,LI Jubo,et al.Automatic feedback correction and deviation analysis for tooth surface of spiral bevel and hypoid gear[J].Journal of Aerospace Power,2011,26(5):1194-1200.(in Chinese)
|
| [16] |
唐进元,卢延峰,周超.调整参数误差对齿面接触质量的影响[J].航空动力学报,2008,23(9):1718-1723.TANG Jinyuan,LU Yanfeng,ZHOU Chao.Effect of machine tool adjustment parameter errors on spiral bevel gears tooth contact quality[J].Journal of Aerospace Power,2008,23(9):1718-1723.(in Chinese)
|
DownLoad: