| Citation: | WANG Xiaozeng, KAN Rui, REN Ming, et al. Film cooling characteristics of compound angle hole on suction side under high-speed conditions[J]. Journal of Aerospace Power, 2023, 38（2）：269-278 doi: 10.13224/j.cnki.jasp.20220544
|
To investigate the film cooling characteristics of compound angle holes on turbine vane under high-speed conditions, a row of compound angle holes were set up on the suction surface of the turbine vane. The film cooling effectiveness and heat transfer coefficient ratio of the compound angle holes were measured. And the net gain of film cooling was measured by net heat flux reduction (NHFR). The effects of Reynolds number, blowing ratio and turbulence intensity on the film cooling effectiveness, heat transfer coefficient ratio and net heat flux reduction were analyzed. It was found that the film cooling effectiveness was affected by the Reynolds number, but when Reynolds number was larger than 6.4×105, the film cooling effectiveness almost didn’t change with Reynolds number any more. When the turbulence intensity increased, the film cooling effectiveness decreased, making it more sensitive to the turbulence intensity at a low blowing ratio. The heat transfer coefficient ratio increased with the blowing ratio, but its sensitivity decreased under higher turbulence intensity. When the turbulence intensity increased, NHFR also increased. In general, at the blowing ratio is 0.8, the compound angle hole presents the best film cooling performance at a higher turbulence intensity.
| [1] |
BUNKER R S. A review of shaped hole turbine film cooling technology[J]. ASME Journal of Heat Transfer,2005,127: 441-453. doi: 10.1115/1.1860562
|
| [2] |
BUNKER R S. Evolution of turbine cooling[R]. ASME Paper GT2017-63205, 2017.
|
| [3] |
EKKAD S, HAN J C. A review of hole geometry and coolant density effect on film cooling[R]. ASME Paper GT 2013-17250, 2013.
|
| [4] |
SCHROEDER R P,THOLE K A. Thermal field measurements for a shaped hole at low and high freestream turbulence intensity[J]. Journal of Turbomachinery,2017,139(2): 1-9.
|
| [5] |
ERIKSEN V L,GOLDSTEIN R J. Heat transfer and film cooling following injection through inclined circular tubes[J]. Journal of Heat Transfer,1974,96(2): 239-245. doi: 10.1115/1.3450171
|
| [6] |
ANDREWS G E, BAZDIDI-TEHRANI F, HUSSAIN C I, et al. Small diameter film cooling hole heat transfer: the influence of the hole length[R]. ASME Paper 91-GT-344, 1991.
|
| [7] |
SCHMIDT D L, BOGARD D G. Pressure gradient effects on film cooling[R]. ASME Paper 95-GT-18, 1995.
|
| [8] |
VANGA S R, REN Z, CLICK A J, et al. Double wall cooling of a full coverage effusion plate with main flow pressure gradient, including internal impingement array cooling[R]. ASME Paper GT2018-77036, 2018.
|
| [9] |
QIN Y,LI X,REN J. Effects of compound angle on film cooling effectiveness with different streamwise pressure gradient and convex curvature[J]. International Journal of Heat and Mass Transfer,2015,86: 482-491. doi: 10.1016/j.ijheatmasstransfer.2015.03.017
|
| [10] |
MOORE J D,YOON C,BOGARD D G. Surface curvature effects on film cooling performance for shaped holes on a model turbine blade[J]. Journal of Turbomachinery,2020,142(11): 1-9.
|
| [11] |
ITO S,GOLDSTEIN R J,ECKERT E R G. Film cooling of a gas turbine blade[J]. Journal of Engineering for Power,1978,100(3): 476-481. doi: 10.1115/1.3446382
|
| [12] |
AMMARI H D,HAY N,LAMPARD D. Effect of acceleration on the heat transfer coefficient on a film-cooled surface[J]. ASME Journal of Turbomachinery,1991,113: 442-449. doi: 10.1115/1.2927894
|
| [13] |
QIN Y, REN J, JIANG H. Effects of streamwise pressure gradient and convex curvature on film cooling effectiveness[R]. ASME Paper GT 2014-25808, 2014.
|
| [14] |
黄逸,徐强,戴韧,等. 叶型表面曲率对离散孔气膜冷却性能的影响[J]. 热能动力工程,2012,27(2): 149-153.
HUANG Yi,XU Qiang,DAI Ren,et al. Effect of blade curvature to film cooling effectiveness of discrete holes[J]. Journal of Engineering for Thermal Energy and Power,2012,27(2): 149-153. (in Chinese)
|
| [15] |
陶智,李林,罗翔,等. 圆形孔排的气膜冷却曲率实验研究[J]. 热科学与技术,2009,8(1): 8-12. doi: 10.3969/j.issn.1671-8097.2009.01.002
TAO Zhi,LI Lin,LUO Xiang,et al. Influence of curvature on film cooling on turbine blade surface[J]. Journal of Thermal Science and Technology,2009,8(1): 8-12. (in Chinese) doi: 10.3969/j.issn.1671-8097.2009.01.002
|
| [16] |
DROST U,BOLCS A. Investigation of detailed film cooling effectiveness and heat transfer distributions on a gas turbine airfoil[J]. Journal of Turbomachinery,1999,121(1): 233-242.
|
| [17] |
LI W,SHI W,LI X,et al. On the flow structures and adiabatic film effectiveness for simple and compound angle hole with varied length-to-diameter ratio by large eddy simulation and pressure sensitive paint techniques[J]. Journal of Heat Transfer,2017,139(12): 122201.1-122201.13.
|
| [18] |
LIGRANI P M,WIGLE J M,CIRIELLO S,et al. Film cooling form holes with compound angle orientations: Part 1 results downstream of two staggered rows of holes with 3d spanwise spacing[J]. Journal of Heat Transfer,1994,116(2): 341-352. doi: 10.1115/1.2911406
|
| [19] |
SEN B,SCHMIDT D L,BOGARD D G. Film cooling with compound angle holes: heat transfer[J]. Journal of Turbomachinery,1989,118(4): 800-806.
|
| [20] |
姚春意,朱惠人,付仲议,等. 主流湍流度对涡轮导叶吸力面W 型气膜孔冷却效率影响的实验研究[J]. 推进技术,2019,40(12): 2779-2787.
YAO Chunyi,ZHU Huiren,FU Zhongyi,et al. Experimental investigation for effects of mainstream turbulence on film cooling effectiveness of W-shaped film hole on suction side of a turbine guide vane[J]. Journal of Propulsion Technology,2019,40(12): 2779-2787. (in Chinese)
|
| [21] |
刘聪,朱惠人,付仲议,等. 涡轮导叶吸力面簸箕型孔气膜冷却特性实验研究[J]. 推进技术,2016,37(6): 1142-1150.
LIU Cong,ZHU Huiren,FU Zhongyi,et al. Experimental study of film cooling characteristics for dust-pan shaped holes on suction side in turbine guide vane[J]. Journal of Propulsion Technology,2016,37(6): 1142-1150. (in Chinese)
|
DownLoad:
