| Citation: | JIANG Yan, LI Haiwang, XIE Gang, et al. Characteristics of shaped holes on the pressure surface of turbine vane[J]. Journal of Aerospace Power, 2024, 39（11）：20220963 doi: 10.13224/j.cnki.jasp.20220963
|
Numerical simulations were employed to investigate the performance of the flow fields and heat transfer characteristics of four types of film holes: cylindrical holes, fan-shaped holes, laidback fan-shaped holes and laidback holes, on pressure surface of the turbine vane. Fan-shaped holes were expanded with the lateral divergence angle of 12 degrees compared with cylindrical holes, and laidback holes expanded with the forward divergence angle of 7 degrees. Furthermore, laidback fan-shaped holes were expanded in both directions. Results showed that fan-shaped holes and laidback fan-shaped holes showed the maximum film cooling effectiveness within the range of blowing ratios. When the blowing ratio was 2, the film cooling effectiveness of fan-shaped holes and laidback fan-shaped holes was improved to the greatest extent by 128.9% and 146.9%, respectively, in contrast with cylindrical. Additionally, laidback fan-shaped holes had the largest net heat flux reduction, 28.8% higher than cylindrical holes, which indicated the laidback fan-shaped hole was the best scheme. And the forward divergence angle had less influence on the flow and heat transfer characteristics than the lateral divergence angle due to inobvious advantages of laidback holes. Besides, the effect of the film cooling effectiveness on net heat flux reduction was dominant on account of similar distributions of net heat flux reduction and the film cooling effectiveness.
| [1] |
BUNKER R S. Film cooling: breaking the limits of diffusion shaped holes[J]. Heat Transfer Research,2010,41(6): 627-650. doi: 10.1615/HeatTransRes.v41.i6.40
|
| [2] |
BERGELES G,GOSMAN A D,LAUNDER B E. The near-field character of a jet discharged normal to a main stream[J]. Journal of Heat Transfer,1976,98(3): 373-378. doi: 10.1115/1.3450563
|
| [3] |
BERGELES G,GOSMAN A D,LAUNDER B E. Near-field character of a jet discharged through a wall at 30 deg Toa mainstream[J]. AIAA Journal,1977,15(4): 499-504. doi: 10.2514/3.7343
|
| [4] |
BERNSDORF S,ROSE M G,ABHARI R S. Modeling of film cooling: Part Ⅰ experimental study of flow structure[J]. Journal of Turbomachinery,2006,128(1): 141-149. doi: 10.1115/1.2098768
|
| [5] |
WALTERS D K,LEYLEK J H. A detailed analysis of film-cooling physics: Part I streamwise injection with cylindrical holes[J]. Journal of Turbomachinery,2000,122(1): 102-112. doi: 10.1115/1.555433
|
| [6] |
GOLDSTEIN R J,ECKERT E R G,BURGGRAF F. Effects of hole geometry and density on three-dimensional film cooling[J]. International Journal of Heat and Mass Transfer,1974,17(5): 595-607. doi: 10.1016/0017-9310(74)90007-6
|
| [7] |
SAUMWEBER C,SCHULZ A. Effect of geometry variations on the cooling performance of fan-shaped cooling holes[J]. Journal of Turbomachinery,2012,134(6): 061008.
|
| [8] |
WANG Chunhua,ZHANG Jingzhou,FENG Hongke,et al. Large eddy simulation of film cooling flow from a fanshaped hole[J]. Applied Thermal Engineering,2018,129: 855-870. doi: 10.1016/j.applthermaleng.2017.10.088
|
| [9] |
KANG Y S,JUN S,RHEE D H. Large eddy simulations on film cooling flow from a fan-shaped cooling hole on a flat plate[J]. The KSFM Journal of Fluid Machinery,2018,21(6): 5-13. doi: 10.5293/kfma.2018.21.6.005
|
| [10] |
PARK S H,KANG Y J,SEO H J,et al. Experimental optimization of a fan-shaped film cooling hole with 30 degrees-injection angle and 6-hole length-to-diameter ratio[J]. International Journal of Heat and Mass Transfer,2019,144: 118652. doi: 10.1016/j.ijheatmasstransfer.2019.118652
|
| [11] |
GAO Zhihong,NARZARY D P,HAN J C. Film-cooling on a gas turbine blade pressure side or suction side with compound angle shaped holes[J]. Journal of Turbomachinery,2009,131(1): 011019.
|
| [12] |
SEO H J,KANG Y J,LEE H C,et al. Optimization of the configuration of the laidback fan-shaped film cooling hole with a lateral expansion angle of 10 degrees[J]. Applied Thermal Engineering,2019,153: 379-389. doi: 10.1016/j.applthermaleng.2019.03.029
|
| [13] |
LEE K D,HUSAIN A,KIM K Y. Multi-objective optimization of a laidback fan shaped film-cooling hole using evolutionary algorithm[J]. International Journal of Fluid Machinery and Systems,2010,3(2): 150-159. doi: 10.5293/IJFMS.2010.3.2.150
|
| [14] |
AGARWAL S,GICQUEL L,DUCHAINE F,et al. Analysis of the unsteady flow field inside a fan-shaped cooling hole predicted by large-eddy simulation[R]. ASME Paper GT2020-14201,2020.
|
| [15] |
JAVADI K,TAEIBI-RAHNI M,DARBANDI M. Jet-into-crossflow boundary-layer control: innovation in gas turbine blade cooling[J]. AIAA Journal,2007,45(12): 2910-2925. doi: 10.2514/1.28770
|
| [16] |
JAVADI A,JAVADI K,TAEIBI-RAHNI M,et al. A new approach to improve film cooling effectiveness using combined jets[EB/OL]. [2022-12-10]. https: //www.researchgate.net/publication/228741776_A_new_approach_to_improve_film_cooling_effectiveness_using_combined_jets.
|
| [17] |
ELY M J,JUBRAN B A. A numerical evaluation on the effect of sister holes on film cooling effectiveness and the surrounding flow field[J]. Heat and Mass Transfer,2009,45(11): 1435-1446. doi: 10.1007/s00231-009-0523-8
|
| [18] |
ELY M J,JUBRAN B A. Film cooling from short holes with sister hole influence[R]. ASME Paper GT2012-68081,2012.
|
| [19] |
KUSTERER K,ELYAS A,BOHN D,et al. A parametric study on the influence of the lateral ejection angle of double-jet holes on the film cooling effectiveness for high blowing ratios[R]. ASME Paper GT2009-59321,2009.
|
| [20] |
BUNKER R S. A review of shaped hole turbine film-cooling technology[J]. Journal of Heat Transfer,2005,127(4): 441-453. doi: 10.1115/1.1860562
|
| [21] |
CHO H H,RHEE D H,KIM B G. Enhancement of film cooling performance using a shaped film cooling hole with compound angle injection[J]. JSME International Journal Series B,2001,44(1): 99-110. doi: 10.1299/jsmeb.44.99
|
| [22] |
SARGISON J E,GUO S M,OLDFIELD M L G,et al. A converging slot-hole film-cooling geometry: Part 1 low-speed flat-plate heat transfer and loss[R]. ASME Paper 2001-GT-0126,2001.
|
| [23] |
BAYRAKTAR S,YILMAZ T. Two-dimensional numerical investigation of film cooling by a cool jet injected at various angles for different blowing ratios[J]. Proceedings of the Institution of Mechanical Engineers,Part C: Journal of Mechanical Engineering Science,2008,222(7): 1215-1224.
|
| [24] |
YU Zhiqiang,LI Chen,AN Baitao,et al. Experimental investigation of film cooling effectiveness on a gas turbine blade pressure surface with diffusion slot holes[J]. Applied Thermal Engineering,2020,168: 114851. doi: 10.1016/j.applthermaleng.2019.114851
|
| [25] |
WANG Chunhua,FAN Fangsu,ZHANG Jingzhou,et al. Large eddy simulation of film cooling flow from converging slot-holes[J]. International Journal of Thermal Sciences,2018,126: 238-251. doi: 10.1016/j.ijthermalsci.2018.01.007
|
| [26] |
ZHANG Guohua,LIU Jian,SUNDÉN B,et al. Comparative study on the adiabatic film cooling performances with elliptical or super-elliptical holes of various length-to-width ratios[J]. International Journal of Thermal Sciences,2020,153: 106360. doi: 10.1016/j.ijthermalsci.2020.106360
|
| [27] |
HOU Rui,WEN Fengbo,LUO Yuxi,et al. Large eddy simulation of film cooling flow from round and trenched holes[J]. International Journal of Heat and Mass Transfer,2019,144: 118631. doi: 10.1016/j.ijheatmasstransfer.2019.118631
|
| [28] |
HUANG Ying,ZHANG Jingzhou,WANG Chunhua. Shape-optimization of round-to-slot holes for improving film cooling effectiveness on a flat surface[J]. Heat and Mass Transfer,2018,54(6): 1741-1754. doi: 10.1007/s00231-017-2272-4
|
| [29] |
PU Jian,ZHANG Tiao,WANG Jianhua. Experimental study of combined influences of wall curvature and compound angle on film cooling effectiveness of a fan-shaped film-hole[J]. International Communications in Heat and Mass Transfer,2022,130: 105834. doi: 10.1016/j.icheatmasstransfer.2021.105834
|
| [30] |
NAJAFABADI H N,KARLSSON M,KINELL M,et al. Film-cooling performance of a turbine vane suction side: the showerhead effect on film-cooling hole placement for cylindrical and fan-shaped holes[J]. Journal of Turbomachinery,2015,137(9): 091005. doi: 10.1115/1.4029966
|
| [31] |
LI Haiwang,ZHAO Guoqin,ZHOU Zhiyu,et al. The characteristics and divergence of fan-shaped and cylindrical holes on the suction side of a turbine blade under rotating conditions[J]. International Journal of Heat and Mass Transfer,2019,139: 432-441. doi: 10.1016/j.ijheatmasstransfer.2019.05.045
|
| [32] |
KO S Y,XU Jingzhong,YAO Yongqing,et al. Film cooling effectiveness and turbulence distribution of discrete holes on a convex surface[J]. International Journal of Heat and Mass Transfer,1984,27(9): 1551-1557. doi: 10.1016/0017-9310(84)90267-9
|
| [33] |
JIANG Yuting,LIN Hongfei,YUE Guoqiang,et al. Aero-thermal optimization on multi-rows film cooling of a realistic marine high pressure turbine vane[J]. Applied Thermal Engineering,2017,111: 537-549. doi: 10.1016/j.applthermaleng.2016.09.143
|
| [34] |
LIU Runzhou,LI Haiwang,LIN Juqiang,et al. An experimental and numerical investigation of film cooling effectiveness on a gas turbine blade tip region[J]. International Journal of Thermal Sciences,2022,177: 107544. doi: 10.1016/j.ijthermalsci.2022.107544
|
| [35] |
LIU Cunliang,XIE Gang,WANG Rui,et al. Study on analogy principle of overall cooling effectiveness for composite cooling structures with impingement and effusion[J]. International Journal of Heat and Mass Transfer,2018,127: 639-650. doi: 10.1016/j.ijheatmasstransfer.2018.07.085
|
| [36] |
LEE S,HWANG W,YEE K. Robust design optimization of a turbine blade film cooling hole affected by roughness and blockage[J]. International Journal of Thermal Sciences,2018,133: 216-229. doi: 10.1016/j.ijthermalsci.2018.07.012
|
| [37] |
YAO Yu,ZHANG Jingzhou,WANG Liping. Film cooling on a gas turbine blade suction side with converging slot-hole[J]. International Journal of Thermal Sciences,2013,65: 267-279. doi: 10.1016/j.ijthermalsci.2012.10.004
|
DownLoad:
