| Citation: | LEI Chunli, SONG Ruizhe, FAN Gaofeng, et al. Vibration characteristics of angular contact ball bearing with local defect considering impact excitation[J]. Journal of Aerospace Power, 2025, 40（2）：20230211 doi: 10.13224/j.cnki.jasp.20230211
|
In order to characterize the operation state of angular contact ball bearing (ACBB) with local defects in detail, a dynamic model of ACBB with local defects considering the impact excitation was proposed to solve the problems of incomplete factors and inadequate description in the traditional model. According to the time-varying displacement excitation model of ACBB with local defects, the instantaneous impact force function related to defect size and bearing speed was established. Based on Hertz contact theory and impact force function, the dynamic calculation method of ACBB with a local defect in outer ring was presented. The vibration characteristics of the ball bearing with faults were investigated, and the dynamic response of the bearing under different working conditions was analyzed. The results showed that with the increase of defect size and load, the fault characteristics frequency of bearing was kept unchanged, but its amplitude increased. With the increase of speed, the frequency of bearing also increased and the amplitude changed. The increase of these three factors could aggravate the vibration of bearing.
| [1] |
刘强. 数控机床发展历程及未来趋势[J]. 中国机械工程,2021,32(7): 757-770. LIU Qiang. Development history and future trends of numerical control machine tools[J]. China Mechanical Engineering,2021,32(7): 757-770. (in Chinese doi: 10.3969/j.issn.1004-132X.2021.07.001
LIU Qiang. Development history and future trends of numerical control machine tools[J]. China Mechanical Engineering, 2021, 32(7): 757-770. (in Chinese) doi: 10.3969/j.issn.1004-132X.2021.07.001
|
| [2] |
吴玉厚. 数控机床电主轴单元技术[M]. 北京: 机械工业出版社,2006. WU Yuhou. Electric spindle unit technology of NC machine tool[M]. Beijing: China Machine Press,2006. (in Chinese
WU Yuhou. Electric spindle unit technology of NC machine tool[M]. Beijing: China Machine Press, 2006. (in Chinese)
|
| [3] |
TANDON N,CHOUDHURY A. A review of vibration and acoustic measurement methods for the detection of defects in rolling element bearings[J]. Tribology International,1999,32(8): 469-480. doi: 10.1016/S0301-679X(99)00077-8
|
| [4] |
唐云冰,高德平,罗贵火. 滚动轴承非线性轴承力及其对轴承系统振动特性的影响[J]. 航空动力学报,2006,21(2): 366-373. TANG Yunbing,GAO Deping,LUO Guihuo. Non-linear bearing force of the rolling ball bearing and its influence on vibration of bearing system[J]. Journal of Aerospace Power,2006,21(2): 366-373. (in Chinese
TANG Yunbing, GAO Deping, LUO Guihuo. Non-linear bearing force of the rolling ball bearing and its influence on vibration of bearing system[J]. Journal of Aerospace Power, 2006, 21(2): 366-373. (in Chinese)
|
| [5] |
MCFADDEN P D,SMITH J D. The vibration produced by multiple point defects in a rolling element bearing[J]. Journal of Sound Vibration,1985,98(2): 263-273. doi: 10.1016/0022-460X(85)90390-6
|
| [6] |
LIEW A,FENG N,HAHN E J. Transient rotordynamic modeling of rolling element bearing systems[J]. Journal of Engineering for Gas Turbines and Power,2002,124(4): 984-991. doi: 10.1115/1.1479337
|
| [7] |
杨将新,曹冲锋,曹衍龙,等. 内圈局部损伤滚动轴承系统动态特性建模及仿真[J]. 浙江大学学报(工学版),2007,41(4): 551-555. YANG Jiangxin,CAO Chongfeng,CAO Yanlong,et al. Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation[J]. Journal of Zhejiang University (Engineering Science),2007,41(4): 551-555. (in Chinese doi: 10.3785/j.issn.1008-973X.2007.04.003
YANG Jiangxin, CAO Chongfeng, CAO Yanlong, et al. Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation[J]. Journal of Zhejiang University (Engineering Science), 2007, 41(4): 551-555. (in Chinese) doi: 10.3785/j.issn.1008-973X.2007.04.003
|
| [8] |
PATEL V N,TANDON N,PANDEY R K. A dynamic model for vibration studies of deep groove ball bearings considering single and multiple defects in races[J]. Journal of Tribology,2010,132(4): 041101.
|
| [9] |
吕延军,曹治军,黑棣,等. 具有陀螺效应的转子-轴承系统的非线性动力学行为[J]. 西安理工大学学报,2010,26(1): 13-19. LYU Yanjun,CAO Zhijun,HEI Di,et al. Nonlinear dynamic behaviors of unsymmetrical rotor-bearing system with gyroscopic effect[J]. Journal of Xi’an University of Technology,2010,26(1): 13-19. (in Chinese doi: 10.3969/j.issn.1006-4710.2010.01.003
LYU Yanjun, CAO Zhijun, HEI Di, et al. Nonlinear dynamic behaviors of unsymmetrical rotor-bearing system with gyroscopic effect[J]. Journal of Xi’an University of Technology, 2010, 26(1): 13-19. (in Chinese) doi: 10.3969/j.issn.1006-4710.2010.01.003
|
| [10] |
王凯,剡昌锋,王风涛,等. 深沟球轴承复合故障动力学特征[J]. 哈尔滨工业大学学报,2020,52(1): 133-140. WANG Kai,YAN Changfeng,WANG Fengtao,et al. Dynamic characteristics of compound fault in deep groove ball bearing[J]. Journal of Harbin Institute of Technology,2020,52(1): 133-140. (in Chinese doi: 10.11918/201809184
WANG Kai, YAN Changfeng, WANG Fengtao, et al. Dynamic characteristics of compound fault in deep groove ball bearing[J]. Journal of Harbin Institute of Technology, 2020, 52(1): 133-140. (in Chinese) doi: 10.11918/201809184
|
| [11] |
SASSI S. A numerical model to predict damaged bearing vibrations[J]. Journal of Vibration and Control,2007,13(11): 1603-1628. doi: 10.1177/1077546307080040
|
| [12] |
牛蔺楷,曹宏瑞,何正嘉. 滚动轴承表面损伤建模与冲击力的定量计算[J]. 振动、测试与诊断,2013,33(增刊1): 5-8,214. NIU Linkai,CAO Hongrui,HE Zhengjia. Rolling bearing surface damage modeling and quantitative calculation of impact force[J]. Journal of Vibration,Measurement & Diagnosis,2013,33(Suppl. 1): 5-8,214. (in Chinese
NIU Linkai, CAO Hongrui, HE Zhengjia. Rolling bearing surface damage modeling and quantitative calculation of impact force[J]. Journal of Vibration, Measurement & Diagnosis, 2013, 33(Suppl. 1): 5-8, 214. (in Chinese)
|
| [13] |
董振振. 滚动轴承复合故障机理及振动模型研究[D]. 哈尔滨: 哈尔滨工业大学,2015. DONG Zhenzhen. Research on multi-fault mechanism andvibration model of rolling element bearings[D]. Harbin: Harbin Institute of Technology,2015. (in Chinese
DONG Zhenzhen. Research on multi-fault mechanism andvibration model of rolling element bearings[D]. Harbin: Harbin Institute of Technology, 2015. (in Chinese)
|
| [14] |
KHANAM S,TANDON,DUTT. Multi-event excitation force model for inner race defect in a rolling element bearing[J]. Journal of Tribology,2016,138(1): 011106. doi: 10.1115/1.4031394
|
| [15] |
邵毅敏,涂文兵. 深沟球轴承三维非线性时变振动特性研究[J]. 振动工程学报,2013,26(6): 831-838. SHAO Yimin,TU Wenbing. 3D nonlinear time-varying vibration characteristics of deep-groove ball bearing[J]. Journal of Vibration Engineering,2013,26(6): 831-838. (in Chinese doi: 10.3969/j.issn.1004-4523.2013.06.004
SHAO Yimin, TU Wenbing. 3D nonlinear time-varying vibration characteristics of deep-groove ball bearing[J]. Journal of Vibration Engineering, 2013, 26(6): 831-838. (in Chinese) doi: 10.3969/j.issn.1004-4523.2013.06.004
|
| [16] |
黄文涛,董振振,孔繁朝. 引入冲击力的滚动轴承内圈故障振动模型[J]. 振动与冲击,2016,35(17) : 121-126,159. HUANG Wentao,DONG Zhenzhen,KONG Fanchao. Vibration model of rolling bearing inner ring fault with impact force[J]. Vibration and Shock,2016,35(17): 121-126,159. (in Chinese
HUANG Wentao, DONG Zhenzhen, KONG Fanchao. Vibration model of rolling bearing inner ring fault with impact force[J]. Vibration and Shock, 2016, 35(17): 121-126, 159. (in Chinese)
|
| [17] |
罗茂林,郭瑜,伍星. 基于时变接触刚度的球轴承双冲击现象动力学建模[J]. 振动工程学报,2018,31(5): 875-882. LUO Maolin,GUO Yu,WU Xing. Dynamic modeling for double impulses behavior of a spalled ball bearing based on time-varying contact stiffness[J]. Journal of Vibration Engineering,2018,31(5): 875-882. (in Chinese
LUO Maolin, GUO Yu, WU Xing. Dynamic modeling for double impulses behavior of a spalled ball bearing based on time-varying contact stiffness[J]. Journal of Vibration Engineering, 2018, 31(5): 875-882. (in Chinese)
|
| [18] |
李昊泽,贺雅,冯坤,等. 考虑时变激励的滚动轴承局部故障动力学建模[J]. 航空学报,2022,43(8): 625176. LI Haoze,HE Ya,FENG Kun,et al. Dynamic modeling of rolling bearing local fault considering time-varying excitation[J]. Acta Aeronautica et Astronautica Sinica,2022,43(8): 625176. (in Chinese
LI Haoze, HE Ya, FENG Kun, et al. Dynamic modeling of rolling bearing local fault considering time-varying excitation[J]. Acta Aeronautica et Astronautica Sinica, 2022, 43(8): 625176. (in Chinese)
|
| [19] |
李志农,周泽文,胡茑庆,等. 考虑冲击力的球轴承复合缺陷动力学建模[J]. 沈阳工业大学学报,2022,44(2): 173-179. LI Zhinong,ZHOU Zewen,HU Niaoqing,et al. Dynamic modeling of composite defects of ball bearing with consideration of impact force[J]. Journal of Shenyang University of Technology,2022,44(2): 173-179. (in Chinese doi: 10.7688/j.issn.1000-1646.2022.02.09
LI Zhinong, ZHOU Zewen, HU Niaoqing, et al. Dynamic modeling of composite defects of ball bearing with consideration of impact force[J]. Journal of Shenyang University of Technology, 2022, 44(2): 173-179. (in Chinese) doi: 10.7688/j.issn.1000-1646.2022.02.09
|
| [20] |
罗丫,杨本梦,涂文兵. 滚动轴承保持架-滚动体接触动力学建模与接触特性[J]. 航空动力学报,2022,37(12): 2887-2895. LUO Ya,YANG Benmeng,TU Wenbing. Dynamic modeling of the contact between cage and rolling element in rolling bearing and contact characteristics[J]. Journal of Aerospace Power,2022,37(12): 2887-2895. (in Chinese
LUO Ya, YANG Benmeng, TU Wenbing. Dynamic modeling of the contact between cage and rolling element in rolling bearing and contact characteristics[J]. Journal of Aerospace Power, 2022, 37(12): 2887-2895. (in Chinese)
|
| [21] |
PETERSEN D,HOWARD C,PRIME Z. Varying stiffness and load distributions in defective ball bearings: analytical formulation and application to defect size estimation[J]. Journal of Sound and Vibration,2015,337: 284-300. doi: 10.1016/j.jsv.2014.10.004
|
| [22] |
巩宝儒. 自旋条件下角接触球轴承刚度分析[D]. 兰州: 兰州理工大学,2020. GONG Baoru. Angular contact ball bearing under spin condition stiffness analysis[D]. Lanzhou: Lanzhou University of Technology,2020. (in Chinese
GONG Baoru. Angular contact ball bearing under spin condition stiffness analysis[D]. Lanzhou: Lanzhou University of Technology, 2020. (in Chinese)
|
| [23] |
周智,朱永生,闫柯,等. 考虑缺陷因素的角接触球轴承七自由度动力学模型[J]. 计算机集成制造系统,2014,20(11): 2836-2842. ZHOU Zhi,ZHU Yongsheng,YAN Ke,et al. Seven degrees of freedom dynamic model of angular contact ball bearing with defects[J]. Computer Integrated Manufacturing Systems,2014,20(11): 2836-2842. (in Chinese
ZHOU Zhi, ZHU Yongsheng, YAN Ke, et al. Seven degrees of freedom dynamic model of angular contact ball bearing with defects[J]. Computer Integrated Manufacturing Systems, 2014, 20(11): 2836-2842. (in Chinese)
|
DownLoad:
