| Citation: | WANG Xinmei, WANG Dafei, LI Lei. Effect of film cooling hole shape on creep properties of CMSX-10 plate specimens[J]. Journal of Aerospace Power, 2025, 40（5）：20230592 doi: 10.13224/j.cnki.jasp.20230592
|
Three types of film holes with inclination and yaw angles, namely circular holes, expansion holes, and W-shaped holes, were designed to study the creep properties of the third-generation nickel based high-temperature alloy CMSX-10 with the cooling blade simulation specimens. High temperature creep tests were conducted to investigate the effect of hole shape on the rupture life of simulation specimens. The results showed that, the rupture life of the circular hole specimen was about 1.3 times that of the expanded hole specimen, and the rupture life of the expanded hole specimen was about 1.3 times that of the W-shaped hole specimen under the average stress of 350 MPa and temperature of 980 ℃. Combined with scanning electron microscopy analysis, it was found that the creep fracture of the sample was a mixed mode of cleavage and dimple fracture caused by stress concentration near the film hole. Based on crystal plasticity theory, simulation analysis was conducted. The simulation results showed stress concentration and redistribution around the film holes. The simulation results can explain the fracture characteristics obtained from experiments. The improved Lemaitre creep damage model and Larson Miller equation were sed to predict the creep fracture life of CMSX-10 flat plate specimens with circular holes. The results showed that the accuracy of predicted creep life based on the improved Lemaitre creep damage model was higher.
| [1] |
CHEN T. Understanding the deformation mechanisms in Ni-based superalloys with using crystal plasticity finite element method[M]. Rolla,US: Missouri University of Science and Technology,2020.
|
| [2] |
KUM D W. Analysis of the threshold stress in the Al-Ti alloys exhibiting high strain rate superplasticity[J]. Materials Science Forum,1996,243/244/245: 287-296.
|
| [3] |
HU Yebing,ZHANG Li,CAO Tieshan,et al. The effect of thickness on the creep properties of a single-crystal nickel-based superalloy[J]. Materials Science and Engineering: A,2018,728: 124-132. doi: 10.1016/j.msea.2018.04.114
|
| [4] |
LE GRAVEREND J B,CORMIER J,GALLERNEAU F,et al. A microstructure-sensitive constitutive modeling of the inelastic behavior of single crystal nickel-based superalloys at very high temperature[J]. International Journal of Plasticity,2014,59: 55-83. doi: 10.1016/j.ijplas.2014.03.004
|
| [5] |
朱惠人,许都纯,刘松龄. 气膜孔形状对排孔下游冷却效率的影响[J]. 航空学报,2002,23(1): 75-78. ZHU Huiren,XU Duchun,LIU Songling. Effects of hole shape on film cooling effectiveness[J]. Acta Aeronautica et Astronautica Sinica,2002,23(1): 75-78. (in Chinese
ZHU Huiren, XU Duchun, LIU Songling. Effects of hole shape on film cooling effectiveness[J]. Acta Aeronautica et Astronautica Sinica, 2002, 23(1): 75-78. (in Chinese)
|
| [6] |
戴萍,林枫. 气膜孔形状对涡轮叶片气膜冷却效果的影响[J]. 热能动力工程,2009,24(5): 560-565,677-678. DAI Ping,LIN Feng. Influence of air-film hole shapes on turbine blade air-film cooling effectiveness[J]. Journal of Engineering for Thermal Energy and Power,2009,24(5): 560-565,677-678. (in Chinese
DAI Ping, LIN Feng. Influence of air-film hole shapes on turbine blade air-film cooling effectiveness[J]. Journal of Engineering for Thermal Energy and Power, 2009, 24(5): 560-565, 677-678. (in Chinese)
|
| [7] |
EKKAD S V,ZAPATA D,HAN J C. Film effectiveness over a flat surface with air and CO2 injection through compound angle holes using a transient liquid crystal image method[J]. Journal of Turbomachinery,1997,119(3): 587-593. doi: 10.1115/1.2841162
|
| [8] |
SCHMIDT D L,SEN B,BOGARD D G. Film cooling with compound angle holes: adiabatic effectiveness[J]. Journal of Turbomachinery,1996,118(4): 807-813. doi: 10.1115/1.2840938
|
| [9] |
ZHANG Bo,LIN Libing,LI Jiquan,et al. Effect of forward expansion angle on film cooling characteristics of shaped holes[J]. Open Physics,2020,18(1): 302-314. doi: 10.1515/phys-2020-0130
|
| [10] |
SEO H J,KANG Y J,LEE H C,et al. Optimization of the configuration of the laidback fan-shaped film cooling hole with a lateral expansion angle of 10 degrees[J]. Applied Thermal Engineering,2019,153: 379-389. doi: 10.1016/j.applthermaleng.2019.03.029
|
| [11] |
GRITSCH M,SCHULZ A,WITTIG S. Adiabatic wall effectiveness measurements of film-cooling holes with expanded exits[J]. Journal of Turbomachinery,1998,120(3): 549-556. doi: 10.1115/1.2841752
|
| [12] |
LI Haiwang,ZHAO Guoqin,ZHOU Zhiyu,et al. The characteristics and divergence of fan-shaped and cylindrical holes on the suction side of a turbine blade under rotating conditions[J]. International Journal of Heat and Mass Transfer,2019,139: 432-441. doi: 10.1016/j.ijheatmasstransfer.2019.05.045
|
| [13] |
EJAZ N,QURESHI I N,RIZVI S A. Creep failure of low pressure turbine blade of an aircraft engine[J]. Engineering Failure Analysis,2011,18(6): 1407-1414. doi: 10.1016/j.engfailanal.2011.03.010
|
| [14] |
吴海华,李涤尘,邢建东. 快速铸造收缩-扩张形气膜孔空心涡轮叶片[J]. 材料科学与工艺,2011,19(6): 143-148. WU Haihua,LI Dichen,XING Jiandong. Rapid casting of hollow turbine blades with converging-expanding film cooling holes[J]. Materials Science and Technology,2011,19(6): 143-148. (in Chinese
WU Haihua, LI Dichen, XING Jiandong. Rapid casting of hollow turbine blades with converging-expanding film cooling holes[J]. Materials Science and Technology, 2011, 19(6): 143-148. (in Chinese)
|
| [15] |
WANG X M,LIU H,ZHOU Q T,et al. Influences of ellipse cooling holes on creep crack initiation and surface morphology of nickel based superalloys[J]. Materials Science and Technology,2013,29(3): 337-341. doi: 10.1179/1743284712Y.0000000155
|
| [16] |
孙兴华. 考虑气膜冷却孔涡轮叶片持久寿命预测的研究[D]. 大连: 大连理工大学,2008. SUN Xinghua. Study of endurance life predict for turbine blade with film cooling hole[D]. Dalian: Dalian University of Technology,2008. (in Chinese
SUN Xinghua. Study of endurance life predict for turbine blade with film cooling hole[D]. Dalian: Dalian University of Technology, 2008. (in Chinese)
|
| [17] |
ERICKSON G L. The development and application of CMSX-10 [R]. Pennsylvania,PA: The Minerals,Metals & Materials Society,1996.
|
| [18] |
艾兴,高行山,温志勋,等. DD6镍基单晶合金气膜孔薄壁平板高温蠕变性能[J]. 航空动力学报,2014,29(5): 1197-1204. AI Xing,GAO Hangshan,WEN Zhixun,et al. Creep behavior of thin-walled plate with cooling holes of nickel-based single crystal superalloy DD6 under high temperature[J]. Journal of Aerospace Power,2014,29(5): 1197-1204. (in Chinese
AI Xing, GAO Hangshan, WEN Zhixun, et al. Creep behavior of thin-walled plate with cooling holes of nickel-based single crystal superalloy DD6 under high temperature[J]. Journal of Aerospace Power, 2014, 29(5): 1197-1204. (in Chinese)
|
| [19] |
VLADIMIROV I N,REESE S,EGGELER G. Constitutive modelling of the anisotropic creep behaviour of nickel-base single crystal superalloys[J]. International Journal of Mechanical Sciences,2009,51(4): 305-313. doi: 10.1016/j.ijmecsci.2009.02.004
|
| [20] |
WEN Zhixun,HOU Nai,YUE Zhu. Creep behaviors of nickel-based single crystal superalloys compact tension specimen at high temperature[J]. Advanced Materials Research,2010,146/147: 1322-1326. doi: 10.4028/www.scientific.net/AMR.146-147.1322
|
| [21] |
张雪莲. 多尺度下镍基单晶高温合金涡轮叶片疲劳蠕变寿命预测[D]. 成都: 电子科技大学,2022. ZHANG Xuelian. Fatigue and creep life prediction of nickel-based single crystal superalloy turbine blade at multiple scales[D]. Chengdu: University of Electronic Science and Technology of China,2022. (in Chinese
ZHANG Xuelian. Fatigue and creep life prediction of nickel-based single crystal superalloy turbine blade at multiple scales[D]. Chengdu: University of Electronic Science and Technology of China, 2022. (in Chinese)
|
DownLoad:
