Film cooling performance and optimization of ellipse conical holes onturbine vanes leading edge
-
摘要:
采用数值仿真方法对椭圆锥孔在高压涡轮导叶前缘的气膜冷却效率进行了探究，分析对比了椭圆柱孔的两个结构参数流向扩张角和径向扩张角对前缘气膜冷却效率的影响，且分别在流向扩张角为0°～18°和径向扩张角为0°～16°范围内对椭圆锥孔进行了优化。结果表明：流向扩张角为1.4°且径向扩张角为11.1°时的椭圆锥孔表现出最高的气膜冷却效率，其相较于圆柱孔的冷却效率提升了147.5%，且椭圆锥孔的结构参数随气膜冷却效率的变化规律可拟合成四次方函数关系，当径向扩张角很小时，气膜冷却效率随流向扩张角增大，反之，气膜冷却效率基本随流向扩张角增大而减小；当流向扩张角较小时，气膜冷却效率大致随径向扩张角的增大而先增后减，当流向扩张角较大时，气膜冷却效率基本保持不变或呈现一个较小的增幅。
Abstract:Simulations were employed to study the film cooling effectiveness of ellipse conical holes on the leading-edge of turbine vane. The influences of two geometry parameters, forward and lateral expansion angle, on the adiabatic film cooling effectiveness were studied comparatively. And optimization was also conducted within the range of forward and lateral expansion angle, 0°—18° and 0°—16°, respectively. Results showed that the ellipse conical hole with a forward expansion angle of 1.4° and a lateral expansion angle of 11.1° presented the highest film cooling effectiveness, which was 147.5% higher than that of the cylindrical hole. Moreover, the relationship between the two geometry parameters and the film cooling effectiveness can be fitted to quartic function. When lateral expansion angle was low, the film cooling effectiveness increased with forward expansion angle. Otherwise, the film cooling effectiveness decreased with forward expansion angle. Additionally, when forward expansion angle was lower, the film cooling effectiveness increased and then decreased with lateral expansion angle. And the film cooling effectiveness was roughly constant or showed a small increase with lateral expansion angle.
-
Key words:
- film cooling effectiveness /
- shaped holes /
- expansion angle /
- turbine vane /
- leading edge
-
图 7 流向扩张角和径向扩张角对冷效的影响规律
Figure 7. Film cooling effectiveness for the effect of forward expansion angle and lateral expansion angle
图 8 样本点及最优点椭圆锥孔绝热冷却效率面分布
Figure 8. Distributions of the film cooling effectiveness for selected design points and the optimum
表 1 回归方程
Table 1. Coefficients in the regression equation
参数 系数 截距 0.039641 δ 0.010705 β 0.009493 δβ −0.00132 δ2 −0.00211 β2 −0.00048 δ2β 0.000041 δβ2 0.000052 δ3 0.000169 β3 0.00003 δ2β2/10−6 −2.57 δ3 β/10−7 1.70 δβ3/10−6 1.53 δ4/10−6 −4.44 β4/10−6 −1.92 
下载: 导出CSV
表 2 回归方程可靠性验证
Table 2. Reliability verification of the regression equation
δ/（°） β/（°） 真实值 预测值 误差/% 0 0 0.0400 0.0396 −1.00 0 4 0.0712 0.0714 0.28 0 8 0.0913 0.0924 1.20 0 12 0.0976 0.0967 −0.92 0 16 0.0662 0.0664 0.30 4.5 0 0.0585 0.0587 0.34 4.5 4 0.0741 0.0733 −1.08 4.5 8 0.0851 0.0856 0.59 4.5 12 0.0922 0.0922 0 4.5 16 0.0780 0.0780 0 9 0 0.0576 0.0596 3.47 9 4 0.0643 0.0623 −3.11 9 8 0.0678 0.0678 0 9 12 0.0769 0.0754 −1.95 9 16 0.0712 0.0726 1.97 13.5 0 0.0713 0.0693 −2.81 13.5 4 0.0645 0.0658 2.02 13.5 8 0.0662 0.0669 1.06 13.5 12 0.0721 0.0745 3.33 13.5 16 0.0809 0.0786 −2.84 18 0 0.0711 0.0713 0.28 18 4 0.0663 0.0676 1.96 18 8 0.0693 0.0669 −3.46 18 12 0.0738 0.0738 0 18 16 0.0803 0.0811 1.00
下载: 导出CSV
-
[1] METZGER D E. Discussion: “film cooling with injection through holes: adiabatic wall temperatures downstream of a circular hole” (Goldstein R J,Eckert E R G,and Ramsey J W,1968,ASME J. Eng. Power,90,pp. 384-393)[J]. Journal of Engineering for Power,1968,90(4): 393-394. doi: 10.1115/1.3609224 [2] BERGELES G,GOSMAN A D,LAUNDER B E. The near-field character of a jet discharged normal to a main stream[J]. Journal of Heat Transfer,1976,98(3): 373-378. doi: 10.1115/1.3450563 [3] BERGELES G,GOSMAN A D,LAUNDER B E. Near-field character of a jet discharged through a wall at 30 deg Toa mainstream[J]. AIAA Journal,1977,15(4): 499-504. doi: 10.2514/3.7343 [4] WALTERS D K,LEYLEK J H. A detailed analysis of film-cooling physics: Part I streamwise injection with cylindrical holes[J]. Journal of Turbomachinery,2000,122(1): 102-112. doi: 10.1115/1.555433 [5] BERNSDORF S,ROSE M G,ABHARI R S. Modeling of film cooling: Part I experimental study of flow structure[J]. Journal of Turbomachinery,2006,128(1): 141-149. doi: 10.1115/1.2098768 [6] GOLDSTEIN R J,ECKERT E R G,BURGGRAF F. Effects of hole geometry and density on three-dimensional film cooling[J]. International Journal of Heat and Mass Transfer,1974,17(5): 595-607. doi: 10.1016/0017-9310(74)90007-6 [7] BAI Bo,LI Zhigang,LI Jun,et al. The effects of axisymmetric convergent contouring and blowing ratio on endwall film cooling and vane pressure side surface phantom cooling performance[J]. Journal of Engineering for Gas Turbines and Power,2022,144(2): 021020. doi: 10.1115/1.4052500 [8] KANG Y S,JUN S,RHEE D H. Large eddy simulations on film cooling flow from a fan-shaped cooling hole on a flat plate[J]. The KSFM Journal of Fluid Machinery,2018,21(6): 5-13. doi: 10.5293/kfma.2018.21.6.005 [9] THOLE K,GRITSCH M,SCHULZ A,et al. Flowfield measurements for film-cooling holes with expanded exits[J]. Journal of Turbomachinery,1998,120(2): 327-336. doi: 10.1115/1.2841410 [10] SAUMWEBER C,SCHULZ A. Effect of geometry variations on the cooling performance of fan-shaped cooling holes[J]. Journal of Turbomachinery,2012,134(6): 1. [11] PARK S H,KANG Y J,SEO H J,et al. Experimental optimization of a fan-shaped film cooling hole with 30 degrees-injection angle and 6-hole length-to-diameter ratio[J]. International Journal of Heat and Mass Transfer,2019,144: 118652. doi: 10.1016/j.ijheatmasstransfer.2019.118652 [12] SEO H J,KANG Y J,LEE H C,et al. Optimization of the configuration of the laidback fan-shaped film cooling hole with a lateral expansion angle of 10 degrees[J]. Applied Thermal Engineering,2019,153: 379-389. doi: 10.1016/j.applthermaleng.2019.03.029 [13] AGARWAL S,GICQUEL L,DUCHAINE F,et al. Analysis of the unsteady flow field inside a fan-shaped cooling hole predicted by large-eddy simulation[C]//Volume 7B: Heat Transfer. American Society of Mechanical Engineers,2020: 1-11. [14] GAO Zhihong,NARZARY D P,HAN J C. Film-cooling on a gas turbine blade pressure side or suction side with compound angle shaped holes[J]. Journal of Turbomachinery,2009,131(1): 011019-011030. doi: 10.1115/1.2813012 [15] CHO H H,RHEE D H,KIM B G. Enhancement of film cooling performance using a shaped film cooling hole with compound angle injection[J]. JSME International Journal Series B,2001,44(1): 99-110. doi: 10.1299/jsmeb.44.99 [16] SARGISON J E,GUO S M,OLDFIELD M L G,et al. A converging slot-hole film-cooling geometry: Part 1 low-speed flat-plate heat transfer and loss[C]// Proceedings of ASME Turbo Expo 2001: Power for Land,Sea,and Air. New Orleans,US: ASME,2001: 453-460. [17] WANG Chunhua,FAN Fangsu,ZHANG Jingzhou,et al. Large eddy simulation of film cooling flow from converging slot-holes[J]. International Journal of Thermal Sciences,2018,126: 238-251. doi: 10.1016/j.ijthermalsci.2018.01.007 [18] LU Yiping. Effect of hole configurations on film cooling from cylindrical inclined holes for the application to gas turbine blades[D]. Baton Rouge,US: Louisiana State University Libraries,2007. [19] HOU Rui,WEN Fengbo,LUO Yuxi,et al. Large eddy simulation of film cooling flow from round and trenched holes[J]. International Journal of Heat and Mass Transfer,2019,144: 118631. doi: 10.1016/j.ijheatmasstransfer.2019.118631 [20] KUSTERER K,ELYAS A,BOHN D,et al. A parametric study on the influence of the lateral ejection angle of double-jet holes on the film cooling effectiveness for high blowing ratios[C]// Proceedings of ASME Turbo Expo 2009: Power for Land,Sea,and Air. Orlando,US: ASME,2009: 199-211. [21] ZHOU Junfei,WANG Xinjun,LI Jun,et al. Effects of diameter ratio and inclination angle on flow and heat transfer characteristics of sister holes film cooling[J]. International Communications in Heat and Mass Transfer,2020,110: 104426. doi: 10.1016/j.icheatmasstransfer.2019.104426 [22] LEE Sanga,HWANG W,YEE K. Robust design optimization of a turbine blade film cooling hole affected by roughness and blockage[J]. International Journal of Thermal Sciences,2018,133: 216-229. doi: 10.1016/j.ijthermalsci.2018.07.012 [23] JONES F B,OLIVER T,BOGARD D G. Adjoint optimization of film cooling hole geometry[C]// Proceedings of ASME Turbo Expo 2021: Turbomachinery Technical Conference and Exposition. Online: ASME,2021: 14-26. [24] BAI L C,ZHANG C,TONG Z T,et al. Optimization of geometric parameters of cylindrical film cooling hole with contoured craters to enhance film-cooling effectiveness[J]. Thermophysics and Aeromechanics,2021,28(6): 835-848. doi: 10.1134/S0869864321060081 [25] PU Jian,ZHANG Tiao,WANG Jian-Hua. Experimental study of combined influences of wall curvature and compound angle on film cooling effectiveness of a fan-shaped film-hole[J]. International Communications in Heat and Mass Transfer,2022,130: 105834. doi: 10.1016/j.icheatmasstransfer.2021.105834 [26] YU Zhiqiang,LI Chen,AN Baitao,et al. Experimental investigation of film cooling effectiveness on a gas turbine blade pressure surface with diffusion slot holes[J]. Applied Thermal Engineering,2020,168: 114851. doi: 10.1016/j.applthermaleng.2019.114851 [27] XIE Gang,TAO Zhi,ZHOU Zhi-Yu,et al. Hole arrangement effect to film cooling performance on leading edge region of rotating blade[J]. International Journal of Thermal Sciences,2021,169: 107034. doi: 10.1016/j.ijthermalsci.2021.107034 [28] 徐永发,李广超,何洪斌,等. 带前缘对吹孔涡轮导向叶片气膜冷却特性实验[J]. 热能动力工程,2022,37(9): 22-30. XU Yongfa,LI Guangchao,HE Hongbin,et al. Experiment on film cooling performance of turbine guide vane with leading edge counter-inclined structure[J]. Journal of Engineering for Thermal Energy and Power,2022,37(9): 22-30. (in ChineseXU Yongfa, LI Guangchao, HE Hongbin, et al. Experiment on film cooling performance of turbine guide vane with leading edge counter-inclined structure[J]. Journal of Engineering for Thermal Energy and Power, 2022, 37(9): 22-30. (in Chinese) [29] ZHOU Wenli,PU Jian,WANG Jianhua,et al. Experimental investigation of hole-geometry effect on unsteady characteristics of film cooling at turbine vane leading edge[J]. International Journal of Thermal Sciences,2022,179: 107715. doi: 10.1016/j.ijthermalsci.2022.107715 [30] HANG Jin,ZHANG Jingzhou. Numerical study of double-jet film cooling on a semi-cylindrical leading edge[J]. Journal of Thermal Science and Engineering Applications,2022,14(8): 081018. doi: 10.1115/1.4054626 [31] JIANG Yan,LI Haiwang,LIU Runzhou,et al. Film cooling comparison of shaped holes among the pressure surface,the suction surface and the leading edge of turbine vane[J]. Applied Thermal Engineering,2023,219: 119343. doi: 10.1016/j.applthermaleng.2022.119343 [32] LIU Cunliang,XIE Gang,WANG Rui,et al. Study on analogy principle of overall cooling effectiveness for composite cooling structures with impingement and effusion[J]. International Journal of Heat and Mass Transfer,2018,127: 639-650. doi: 10.1016/j.ijheatmasstransfer.2018.07.085 [33] YAO Yu,ZHANG Jingzhou,WANG Liping. Film cooling on a gas turbine blade suction side with converging slot-hole[J]. International Journal of Thermal Sciences,2013,65: 267-279. doi: 10.1016/j.ijthermalsci.2012.10.004 -
点击查看大图
计量
- 文章访问数: 41
- HTML浏览量: 35
- PDF量: 7
- 被引次数: 0