涡流管结构参数对其性能的影响

计玉帮; 吴玉庭; 丁雨; 何曙; 姜曙; 马重芳

涡流管结构参数对其性能的影响

北京工业大学环境与能源工程学院传热强化与过程节能教育部重点实验室传热与能源利用北京市重点实验室, 北京 100022

基金项目: 国家重点基础研究发展计划(973)资助(TG2000026304)

计量
- 文章访问数: 1779
- HTML浏览量: 95
- PDF量: 446
- 被引次数: 0
出版历程
- 收稿日期: 2005-04-11
- 修回日期: 2005-06-06
- 刊出日期: 2006-02-28

Study of the Influence of Structural Parameters on the Vortex Tube Performance

Key Laboratory of Beijing Municipality on "Heat Transfer and Energy Conversion", Key Laboratory of the Ministry of Education on"Enhanced Heat Transfer and Energy Conversion", College of Environmental and Energy Engineering, Beijing University of Technology, Beijing 100022, China

摘要

摘要: 用实验方法研究了热端管管长、分离室直径、冷孔板孔径等主要结构参数对涡流管的制冷制热性能的影响。实验中以空气为介质分别对不同结构参数涡流管的性能进行了研究,得出了热端管管长、分离室直径以及冷孔板孔径等参数对涡流管制冷制热性能的影响规律。研究结果表明:在一定范围内增加热端管长度有利于涡流管的能量分离;在大冷流率下,大直径涡流管的制冷性能优于小直径涡流管;冷孔板孔径愈小,涡流管的制冷制热效应都愈好,在冷孔板孔径与热端管内径之比为50%时,取得最佳的制冷制热效应。
- 航空、航天推进系统 /
- 涡流管 /
- 结构参数 /
- 制冷效应 /
- 制热效应 /
- 制冷效率
Abstract: The influence of different configurations,such as vortex tube length,separation chamber diameter and cold plate diameter on the vortex tube performance was investigated by experiment with air as medium.The main influence of length and diameter on the vortex tube performance was obtained in this paper.The result indicates that the performance can be improved by the increase of hot tube length in a certain range.The cooling effect of vortex tube with larger separation chamber diameter is better than that with smaller diameter in the condition of higher cold mass flow fraction.The less the diameter of cold plate is,the better performance will be.The best cooling effect and heating effect occur at the diameter ratio of hot section inner diameter to cold plate hole diameter being 50%.
- aerospace propulsion system /
- vortex tube /
- structural parameter /
- cooling effect /
- heating effect /

HTML

参考文献(6)

[1]	Ranque G J.Method and Apparatus for Obtaining from a Fluid under Pressure Two Currents of Fluid at Different Temperatures[Z].United States Patent 1952281.March 27,1934.
[2]	Hartnett J P.Experimental Study of the Velocity and Temperature Distribution in a High-Velocity Vortex-Type Flow[J].Transactions of the ASM E Journal of Heat Transfer,1957,(5);751～758.
[3]	Hilsch R.The Use of the Expansion of Gases in a Centrifugal Field as a Cooling Process[J].Review Sciences Instruments,1947,(18) ;108～113.
[4]	Soni Y,Thomson W.Optimal Design of the Ranque-Hilsch Vortex Tube[J].Transactions of the ASME,Journal of Heat Transfer,1975,(5) ;316～317.
[5]	Saidi M H,Allaf Yazdi M R.Energy Model of a Vortex Tube System with Experimental Results[J].Energy,1999,24; 625～632.
[6]	姜曙,叶芳,俞坚,等.三流道喷嘴涡流管能量分离特性的研究[J].工程热物理学报,2004,25(3);499～501.Jiang Shu,Ye Fang,Yu Jian.The Performance Study on Energy Separation in Vortex Tube of Tri-Channels[J].Journal of Engineering Thermoplysics,2004,25 (3); 499 ～ 501.