离散孔切向进气气膜冷却效率的实验

马国锋; 张靖周; 杨卫华

离散孔切向进气气膜冷却效率的实验

南京航空航天大学能源与动力学院, 江苏南京 210016

计量
- 文章访问数: 1513
- HTML浏览量: 1
- PDF量: 496
- 被引次数: 0
出版历程
- 收稿日期: 2005-05-13
- 修回日期: 2005-10-11
- 刊出日期: 2006-04-28

Experimental Investigation on Film Cooling Effectiveness of Tangential Discrete Holes Configuration

College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Beijing 210016, China

摘要

摘要: 采用红外热像仪对具有不同孔径和排列方式的离散孔切向进气的气膜冷却结构的绝热壁温进行了测试,获得了气膜冷却效率随吹风比和无量纲流向距离变化的经验关联式。研究结果表明,在本文研究的参数范围内,离散孔切向进气气膜冷却的冷却效率随吹风比和气膜孔直径的增大而上升;在气膜孔板开孔率和吹风比相同时,由排型引起的冷却效率差异不是很大。
- 航空、航天推进系统 /
- 气膜冷却 /
- 冷却效率 /
- 实验研究
Abstract: The film cooling effectiveness of the tangential discrete holes film cooling configuration with different hole diameters and arrangement was experimentally investigated using infrared camera.The empirical correlations of cooling effectiveness to blowing ratio and non-dimensional flow-wise distance(X/S) were obtained,which agreed well with the experimental results.The results show that,for the present investigation conditions,the film cooling effectiveness will be increased with the increase of blowing ratios and the diameter of film hole;with the same blowing ratios and porosity of holes,the hole arrangement has little effect on cooling effectiveness.
- aerospace propulsion system /
- film cooling /
- cooling effectiveness /
- experimental investigation

HTML

参考文献(10)

[1]	葛绍岩,徐靖中.气膜冷却[M].北京:科学出版社,1995.
[2]	Sturgess G J.Application of Film Cooling Theory to the Cooling of Aircraft Gas turbine Chambers[J].Journal of the Royal Aeronautical Society,1967,71:430 ～ 434.
[3]	Rastogi A K,WhiteLaw J H.The Effectiveness of Three-Dimensional Film-Cooling slots-I:Measurements[J].International Journal of Heat and Mass Transfer,1973,16:1665～1681.
[4]	Sturgess G J.Account of Film Turbulence for Predicting Film Cooling Effectiveness in Gas Turbine Combustors[J].ASME Journal of Engineering for Power,1980,102:524 ～ 534.
[5]	Sturgess G J.Design of Combustor Cooling Slots for Hign Film Effectiveness:Part Ⅰ -Film General Development[J].ASME Journal of Engineering for Gas Turbines and Power,1986,108:354～360.
[6]	Sturgess G J.Design of Combustor Cooling Slots for High Film Effectiveness:Part Ⅱ-Film Initial Region[J].ASME Journal of Engineering for Gas Turbines and Power,1986,108:361～369.
[7]	Hyung Hee Cho,Jin Ki Ham.Influence of Injection Type and Feed Arrangement on Flow and Heat Transfer in an Injection Slot[J].ASME Journal of Turbomachinery,2002,124:132～141.
[8]	Nasir S,Ekkad S V,Acharya S.Effect of Compound Angle Injection on Flat Surface Film Cooling with Large Streamwise Injection Angle[J].Experimental Thermal and Fluid Science,2001,25:23～ 29.
[9]	Yuen C H N,Martinez-Botas R F.Film Cooling Characteristics of a Single round Hole at Various Streamwise Angles in a Cross Flow:Part Ⅰ --Heat Transfer Coefficients[J].International Journal of Heat and Mass Transfer,2003,46:237～249.
[10]	张小英,王先炜.比较研究多种气膜冷却模型的冷却效果[J].航空动力学报,2002,17(4):475～479.Zhang Xiaoying,Wang Xianwei.Study on Cooling Effectiveness of Various Film Coolings[J].Journal of Aerospace Power,2002,17 (4):475 ～ 479.