特殊形状橡胶密封圈的性能分析

孙健; 迟可伟; 冯茂林; 张文明

特殊形状橡胶密封圈的性能分析

北京科技大学土木与环境工程学院车辆工程研究所, 北京 100083

计量
- 文章访问数: 1551
- HTML浏览量: 0
- PDF量: 441
- 被引次数: 0
出版历程
- 收稿日期: 2005-10-17
- 修回日期: 2005-12-01
- 刊出日期: 2007-01-28

Performance analysis of special cross section rubber seal ring

Vehicle Engineering Research Center, Civil and Environmental Engineering School, University of Science and Technology, Beijing 100083, China

摘要

摘要: 采用非线性有限元法对特殊截面形状的橡胶密封圈进行了分析.通过轴对称有限元分析模型, 分析了其在矩形沟槽内装配压缩过程中的变形和应力变化, 以及应力的分布情况, 同时还对承受单侧压力的密封情况进行了研究.对于密封圈的抗扭转特性以及在特殊压力负载情况下的密封特性也进行了模拟并且和普通O形圈进行了对比.结果表明, 所采用的方法能够预测特殊形状的密封圈在压缩中的变形和应力等特征参数, 加深了对其密封性能的了解, 并对同类密封结构设计有一定的指导意义.
- 航空、航天推进系统 /
- 橡胶密封圈 /
- 特殊形状 /
- 非线性 /
- 有限元
Abstract: The response of special cross section rubber seal ring during squeeze and pressurization was studied by non-liner finite element method.A finite element model had been built to approximate the response of an axisymmetric special cross section rubber seal ring in a rectangular joint groove.The deformation and stress distribution during squeeze and pressurization were studied based on the large displacement,incompressible ginite element model with two terms Moone-Rivilin in the strain energy function.Meanwhile,the simulated results were compared with those of general O-ring in the same case.The model is proved to be able to predict the characteristic parameters of deformation and stress of special shape seal rings during pressurization.Deeper understanding of the seal performance is obtained,and it is useful for further designing of this type of sealing structure.
- aerospace propulsion system /
- rubber seal ring /
- special cross section /
- non-linear /
- finite element

HTML

参考文献(12)

[1]	(德)海因茨 K 米勒,(英)伯纳德 S 纳乌著.流体密封技术[M].北京:机械工业出版社,2002.
[2]	顾永泉.流体动密封(下)[M].北京:中国石化出版社,1992.
[3]	吕和祥.橡皮轴对称大变形分析[J].大连工学院学报,1984,23(1):17-23.LU Hexiang.Analysis of axisymmetric large deformation of rubber[J].Journal of Dalian Institute of Technology,1984,23(1):17-23
[4]	吕和祥.橡皮环大变形接触问题[J].应用数学和力学,1986,7(3):239-248.LU Hexiang.Contact problem of rubber rings with large deformation[J].Applied Mathematics and Mechanics.1986,7(3):239-248.
[5]	廖日东,左正兴,邹文胜.O 形圈轴对称超弹性接触问题的有限元分析[J].润滑与密封,1996(5):30-33.LIAO Ridong,ZUO Zhengxing,ZOU Wensheng.Finit element analysis of the axial symmetric hyperelastic contact problem of O ring[J].Lubrication Engineering.1996(5):30-33.
[6]	任全彬,陈汝训,杨卫国.橡胶O形圈的变形及应力分析[J].航空动力学报,1995,10(3):241-244REN Quanbin,CHEN Ruxun,YANG Weiguo.Deformation and stress analysis of rubber O-ring[J].Journal of Aerospace Power.1995,10(3):241-24.
[7]	Salita M.A simple finite element model of o-ring deformation and activation during squeeze and pressurization[R].Paper AIAA-87-1739.American Institute of aeronautics and astronautics,1987.
[8]	Gadia M S.Alternative methods for the solution of hyperelastic problems with incompressibility[J].Computer and Structures,1992,42(1):1-10.
[9]	蒋友谅.非线性有限元法[M].北京:北京工业学院出版社,1988.
[10]	ANSYS理论手册[M].美国ANSYS公司,2002.
[11]	王勖成,邵敏.有限单元法基本原理和数值方法[M].北京:清华大学出版社,1997.
[12]	巴斯.工程分析中的有限元法[M].北京:机械工业出版社,1991.