液体火箭发动机试验台贮箱增压系统数值仿真

陈阳; 张振鹏; 瞿骞; 朱子环

液体火箭发动机试验台贮箱增压系统数值仿真

1.
北京航空航天大学宇航学院, 北京 100083
2.
北京航天试验技术研究所, 北京 100074

计量
- 文章访问数: 1733
- HTML浏览量: 5
- PDF量: 431
- 被引次数: 0
出版历程
- 收稿日期: 2005-12-12
- 修回日期: 2006-05-09
- 刊出日期: 2007-01-28

Numerical simulation f or tank pressurization system of L RE test-bed

1.
School of Astronautics, Beijing University of Aeronautics and Astronautics, Beijing 100083, China
2.
Beijing Institute of Aerospace Testing Technology, Beijing 100074, China

摘要

摘要: 在不考虑传热传质的情况下建立了一种简化的贮箱模型, 并采用液体火箭发动机试验台气路系统通用模块化建模与仿真软件对容腔放气过程和某试验台贮箱增压系统在发动机点火工作段的增压过程进行了仿真, 计算结果与分析解和试验结果获得了较好的一致, 验证了软件的有效性和通用性.对两个系统的建模过程表明软件所采用的模块化建模与仿真方法适用于对复杂管网的建模, 在液体火箭发动机系统仿真上具有较好的应用前景.对贮箱增压系统的仿真表明, 合理设计PID控制参数并根据经验预置与额定流量相近的调节阀初始开度, 对于提高增压系统起动过程的平稳性有利.
- 航空、航天推进系统 /
- 液体火箭发动机 /
- 试验台贮箱增压系统 /
- 数值仿真 /
- PID控制
Abstract: A simple model of propellant tank was established by neglecting mass and heat transfer between the propellant and pressurant.Then by employing the modularization modeling and simulation software for liquid rocket engine（LRE） test-bed gas system（LRETBMMSS-GS）,blowdown of a tank and pressurization of a LO₂ tank pressurization system during engine firing were simulated.The simulation results are in good agreement with the analytical solution and test data.Accordingly,the software is validated to be effective and versatile.The progress of modeling two systems shows that the method of MMS is suitable for modeling complicated LRE system and can be used to simulate all kinds of working processes of LRE system.The simulation of LO₂ tank pressurization system indicates that PID control parameters should be set reasonably and the initial opening of pneumatic diaphragm control valve should be adjusted to nominal pressurant mass rate,which is effective to improve stability of pressurization starting transient.
- aerospace propulsion system /
- liquid rocket engine(LRE) /
- tank pressurization system of LRE test-bed /
- numerical simulation /
- PID control

HTML

参考文献(11)

[1]	张育林,刘昆,程谋森.液体火箭发动机动力学理论与应用[M].北京:科学出版社,2005.
[2]	Holt K,Majumdar A.Numerical modeling and test data comparison of propulsion test article helium pressurization System[R].AIAA 2000-3719.
[3]	Majumdar A,Steadman T.Numerical modeling of pressurization of a propellant tank.AIAA 99-0879.
[4]	Zilliac G,Karabeyoglu M A.Modeling of propellant tank pressurization.AIAA 2005-3549.
[5]	瞿骞.高压、小气枕低温贮箱智能增压技术[J].低温工程,2005,(5):22-25.QU Qian.An intelligence pressurization technology of high pressure and small ullage at low temperature tank[J].Cryogenics,2005,(5):22-25.
[6]	郭霄峰主编.液体火箭发动机试验[M].北京:宇航出版社,1990:284-286.
[7]	陈阳,高芳,张振鹏,等.液体火箭发动机试验台贮箱增压系统模块化仿真[J].航空动力学报,2005,20(2):339-344.CHEN Yang,GAO Fang,ZHANG Zhenpeng,et al.Modular simulation for tank pressurization system of LRE test-bed[J].Journal of Aerospace Power,2005,20(2):339-344.
[8]	陈阳,高芳,张黎辉,等.减压器动态仿真的有限体积模型[J].推进技术,2006,27(1):9-14.CHEN Yang,GAO Fang,ZHANG Lihui,et al.Finite volume model for numerical simulation on dynamic process of pressure reducing regulator[J].Journal of Propulsion Technology,2006,27(1):9-14.
[9]	陈阳,高芳,张振鹏,等.气动薄膜调节阀控制系统工作过程的动态仿真[A].第五届液体火箭推进专业委员会第一次会议论文集[C],三亚:中国宇航学会,2005:316-324.
[10]	Majumdar A,Bailey J W,Schallhorn P,et al.A generalized fluid system simulation program to model flow distribution in fluid networks[R].AIAA 98-3682.
[11]	陈新华主编.运载火箭推进系统[M].北京:国防工业出版社,2002.