基于伴随非等温射流理论的缝槽气膜冷却模型

张弛; 林宇震; 许全宏

基于伴随非等温射流理论的缝槽气膜冷却模型

北京航空航天大学能源与动力工程学院航空发动机气动热力重点实验室, 北京 100083

计量
- 文章访问数: 1570
- HTML浏览量: 3
- PDF量: 502
- 被引次数: 0
出版历程
- 收稿日期: 2006-11-20
- 修回日期: 2007-01-16
- 刊出日期: 2007-12-28

A prediction model of film-cooling adiabatic effectiveness based on cohence non-isothermal jet theory

National Key Laboratory on Aero-Engines, School of Jet Propulsion, Beijing University of Aeronautics and Astronautics, Beijing 100083, China

摘要

摘要: 在伴随非等温射流基础上发展了一种适用于缝槽气膜冷却绝热温比预估的数学模型.通过合理假设推导出二维壁面射流混合层核心温度分布规律,将其作为气膜绝热壁温,并考虑缝槽几何特征参数和气膜吹风比对冷却效率的影响,得到绝热温比计算公式.用试验数据对该预估模型进行拟合分析,得到了与试验数据拟合精度在±8%以内的半经验预估模型,证明该模型的可行性和应用潜力,并需要更多的试验数据对其进行验证和改进.
- 航空、航天推进系统 /
- 航空发动机 /
- 燃烧室 /
- 缝槽气膜冷却 /
- 绝热温比 /
- 伴随非等温射流模型
Abstract: To predict the slot film-cooing adiabatic effectiveness,a mathematic model was developed based on cohence non-isothermal jet theory.The core temperature distribution of mixing layer in₂Dwall jet was deduced through reasonable assumptions,and the temperature was regarded as the adiabatic wall temperature.In addition,this influence of slot geometry parameter and film blowing ratio on the cooling effectiveness was also considered,so the adiabatic effectiveness equation was obtained.The empirical coefficients in this prediction model should be fitted to the experimental data,showing that the present prediction model has an accuracy of within ±8% to all previous experimental data.The feasibility and potential application of this model have been demonstrated,and more experimental data are required for future verification and improvement.
- aerospace propulsion system /
- aircraft engine /
- combustor /
- slot film cooling /
- adiabatic effectiveness /
- cohence non-isothermal jet

HTML

参考文献(11)

[1]	Jubasz A J,Marek C J.Lewis research center combustor liner film cooling in the presence of high free-stream turbulence[R].NASA TN D-6360,1971.
[2]	Sturgess G J.Design of combustor cooling slots for high film effectiveness:Part Ⅱ-Film initial region[J].Journal of Engineering for Gas Turbine and Power,1986,108:361-369.
[3]	Sturgess G J.Design of combustor cooling slots for high film effectiveness:Part Ⅰ-Film general development[J].Journal of Engineering for Gas Turbine and Power,1986,108:354-360.
[4]	Mongia H C,Kumar G N.Validation of an advanced turbulence model with DOE film-effectiveness test data on a machined ring liner[R].Salt Lake City:37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit,AIAA 2001-3269,2001.
[5]	Li S C,Mongia H C.An improved method for correlation of film-cooling effectiveness of gas turbine combustor li-ners[R].Salt Lake City:37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit,AIAA 2001-3268,2001.
[6]	金如山.航空燃气轮机燃烧室[M].北京:宇航出版社,1988:340-373.
[7]	Lefebvre A H.Gas turbine combustion[M].2nd ed.Phicdelphia:Talor & Francis,1999:289-293.
[8]	葛绍岩,刘登瀛,许靖中,等.气膜冷却[M].北京:科学出版社,1985:93-105.
[9]	谢象春.湍流射流理论与计算[M].北京:科学出版社,1975:178-216.
[10]	赵承庆,姜毅.气体射流动力学[M].北京:北京理工大学出版社,1998:113-115.
[11]	张弛,许全宏,林宇震.不同缝槽进气孔间距的纯气膜绝热温比试验研究[J].航空动力学报,2006,21(3):533-537.ZHANG Chi,XU Quanhong,LIN Yuzhen.Experimental investigation on the film-cooling adiabatic effectiveness with different slot inlet hole pitches[J].Journal of Aerospace Power,2006,21(3):533-537.