几种紧凑回热面传热和流动的实验和数值研究

彭浩; 孙志江; 凌祥

几种紧凑回热面传热和流动的实验和数值研究

南京工业大学机械与动力工程学院, 南京 210009

计量
- 文章访问数: 1371
- HTML浏览量: 133
- PDF量: 460
- 被引次数: 0
出版历程
- 收稿日期: 2006-12-26
- 修回日期: 2007-04-20
- 刊出日期: 2008-01-28

Numerical and experimental study on flow and heat transfer performance of some compact surface recuperators

School of Mechanical and Power Engineering, Nanjing University of Technology, Nanjing 210009, China

摘要

摘要: 运用计算流体动力学方法,建立单元控制体模型,对回热器主要型面(不锈钢锯齿型面、CC型一次表面)的传热及流动特性进行了数值模拟,并与实验结果进行对比,结果表明,数值结果与实验结果吻合的较好.在此基础上,研究了CC型面结构参数等对传热流动性能的影响,并且通过j/f的大小比较了不同结构参数下CC型面以及不锈钢锯齿型面的表面性能,为回热器的优化设计提供依据.
- 航空、航天推进系统 /
- 回热器 /
- 不锈钢锯齿型面 /
- CC型面 /
- 数值模拟
Abstract: A unit control model was established using computational fluid dynamic(CFD) method,while the heat transfer and fluid flow performances on primary surface of recuperator(stainless steel serrated fin and cross corrugated(CC) primary surface) were simulated numerically and also compared with the experimental results.The results show good consistency between numerical simulation and experimental data.To this end,the effect of CCsurface structural parameters on heat transfer performance was discussed,and then the heat transfer and flow characteristics were compared for different structural scales and surface arrangements,thus providing a basis for design optimization of recuperators.
- aerospace propulsion system /
- recuperator /
- stainless steel serrated fin /
- corrugated cross(CC)surface /
- numerical simulation

HTML

参考文献(13)

[1]	McDonald C F.Low cost recuperator concept for microturbine applications[R].ASME 2000-GT-167,2000.
[2]	Gunnar L,Max X.High performance and cost effective recuperator for micro-gas turbines[R].ASME GT-2002-30402,2002.
[3]	Ciofalo M,Stasiek J,Collins M W.Investigation of flow and heat transfer in corrugated passages-Ⅰ experimental results[J].International Journal of Heat Mass transfer,1996,39:149-164.
[4]	Utriainen E,Sunden B.Evaluation of the cross corrugated and some other candidate heat transfer surfaces for microturbine recuperators[J].ASME Journal of Engineering for Gas Turbines and Power,2002,12:550-560.
[5]	Campbell J F,Rohsenow W M.Gas turbine regenerators:a method for selecting the optimum plate-finned surface pair for minimum core volume[J].International Journal of Heat Mass Transfer,1992,35:3441-3450.
[6]	Shan R K.Compact heat exchanger technology and applications[M]//Heat Exchange Engineering:Vol.2,London:Ellis Horwood Limited,1991.
[7]	Sparrow E M,Hajiloo A.Measurements of heat transfer and pressure drop for an array of staggered plates aligned parallel to an air flow[J].Transactions of the ASME,1980,102:426-432.
[8]	Sparrow E M,Liu C H.Heat transfer pressure drop and performance relationships for inline,staggered and continuous plate heat exchangers[J].Int.J.Heat Mass Transfer,1979,22:1613-1625.
[9]	Joshi H M,Webb R L.Heat transfer and friction in the offset strip-fin heat exchanger[J].International Journal of Heat Mass Transfer,1987,30:69-84.
[10]	Manglik R M,Bergles A E.Heat transfer and pressure drop correlations for the rectangular offset strip fin compact heat exchanger[J].Experimental Thermal and Fluid Science,1995,10:171-180.
[11]	Utriainen E.Investigation of some heat transfer surface for gas turbine recuperator[R].Sweden,Lund:Lund Institute of Technology,2001.
[12]	Ciofalo M,Collins M W,Henry F S.Laminar and turbulent flow and heat transfer in crossed corrugated heat exchangers[J].In Numerical Methods for Thermal Problems,1991,8:622-638.
[13]	NIE Song,QU Wei.Numerical simulation on heat transfer and flow performances of CC primary surface recuperator[J].Journal of Engineering Thermophysics,2004,25(6):899-991