外涵引气加力喷油杆冷却特性模拟实验

闫宝华; 樊未军; 李瑞明; 杨茂林

外涵引气加力喷油杆冷却特性模拟实验

北京航空航天大学能源与动力工程学院, 北京 100191

计量
- 文章访问数: 1581
- HTML浏览量: 144
- PDF量: 462
- 被引次数: 0
出版历程
- 收稿日期: 2007-10-22
- 修回日期: 2007-12-17
- 刊出日期: 2008-10-28

Experimental research on the cooling characteristics of an afterburner fuel injector with double-wall construction

School of Jet Propulsion, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 根据实际需要,提出了新型外涵引气双层壁喷油杆的结构方案.共设计了不同结构尺寸的8种新型双层喷油杆冷却套,在流动特性研究的基础上进一步对其换热特性和高温工况下流动性能进行了对比实验.综合其引气和冷却性能,对比八种尺寸套管,选取了较为合适的冷却套管结构尺寸.并对这种尺寸的套管进行了油杆内壁温度沿杆高的变化、油杆内壁温度随冷却气总压的变化及油杆内壁温度随套管进口雷诺数的变化的研究.实验表明:可以有效从外涵引气(压差850 Pa时,引气量9 g/s),能够较大降低油杆内壁温度(冷却效率0.7以上).
- 加力燃烧室 /
- 喷油杆 /
- 气冷
Abstract: A new afterburner fuel injector with double-wall construction was presented to meet the actual requirements.8 test pieces of new fuel injector casings with different sizes were designed in this research.The heat transfer characteristics and cooling air flow performance were tested based on previous flow characteristics research.In view of the air extraction and cooling performance,an optimum cooling case was selected.Then,this casing of fuel injector was researched with respect to the distribution of injector temperature,change of injector temperature with cooling flow inlet total pressure and change of injector temperature with Re of cooling flow inlet.The results show that: this new afterburner fuel injector can extract enough cooling air from the fan stream(When Δp is 850 Pa,extracted air flow flux is 9 g/s) and decrease effectively the temperature of the wall of fuel injector(cooling efficiency is not less than 0.7).
- afterburner /
- fuel injector /
- air cooling

HTML

参考文献(4)

[1]	郭成富,王勇,曹康,等.加力燃烧室喷油杆结焦实验研究[J].燃气涡轮实验与研究,1997,10(1):30-31.GUO Chengfu.WANG Yong.CAO Kang.Experimental research on the coke deposited in the afterburner fuel injeetor[J].Gas Turbine Experiment and Research,1997,10(1):30-31.(in Chinese)
[2]	白兴艳,张频捷,岳连捷,等.加力用气冷与气动雾化喷油杆的性能研究[J].航空动力学报,2000,15(4):39-392.BAI Xingyan,ZHANG Pinjie,YUE Lianjie et al.Research on performance of an afterburner air blast spraybar[J].Journal of Aerospace Power,2000,15(4):391-392.(in Chinese)
[3]	Lovett J A,Brogan T P,Philippona D S.Development need for advanced afterburner designs[R].AIAA 2004-4192.
[4]	吴伟民,王月贵,李华廷,等.加力燃油管传热特性研究EJ3.燃气涡轮实验与研究,1997,1 O(1):9-12.WU Weimin,WANG Yuegui,LI Huating,et al.Research on heat transfer characteristics of the afterburner fuel injector[J].Gas Turbine Experiment and Research,1997,10(1):9-12.(in Chinese)