弧齿锥齿轮激励研齿的动态研磨分析与试验

杨建军; 邓效忠; 魏冰阳; 方宗德

弧齿锥齿轮激励研齿的动态研磨分析与试验

1.
河南科技大学机电工程学院,洛阳 471003
2.
西北工业大学机电学院,西安 710072

基金项目: 国家自然科学基金(50475060)

计量
- 文章访问数: 1705
- HTML浏览量: 128
- PDF量: 365
- 被引次数: 0
出版历程
- 收稿日期: 2009-11-08
- 修回日期: 2010-04-02
- 刊出日期: 2010-12-28

Study and experiments of dynamic mechanism of excited gear lapping of spiral bevel gear

1.
School of Mechatronics Engineering, Henan University of Science and Technology,Luoyang 471003,China
2.
School of Mechanical Engineering, Northwestern Polytechnical University,Xian 710072,China

摘要

摘要: 建立了包含齿侧间隙、传动误差和时变啮合刚度等因素的10自由度弧齿锥齿轮研齿系统的动力学模型,针对普通研齿的不足之处,提出了激励研齿加工方法,对普通研齿和激励研齿动态位移响应和动态研磨力进行了对比分析,结果表明激励研齿方法使工作齿面和非工作齿面同时得到研磨,增加了研齿时的动态研磨力.超声激励下的弧齿锥齿轮研齿试验表明激励研齿方法能提高研齿的效率,提高齿形精度,改善齿面质量和轮齿啮合特性.
- 弧齿锥齿轮 /
- 激励研齿 /
- 动态研磨力 /
- 齿面误差 /
- 超声研齿
Abstract: A ten-freedom-degrees dynamic model of spiral bevel gear lapping system was established with the consideration of tooth backlash,transmission error and time-varying meshing stiffness.For the disadvantages of conventional gear lapping method,the excited gear lapping method was introduced in this paper.The dynamic lapping force and normal vibration displacement at meshing point between conventional gear lapping and excited gear lapping were analyzed.The results show that both the drive side and non-drive side of the tooth can be lapped at the same time by applying excited gear lapping method.The results of ultrasonic gear lapping experiment show that the quality of gear face is improved and the gear lapping efficiency is increased.
- spiral bevel gear /
- excited gear lapping /
- dynamic lapping force /

HTML

参考文献(12)

[1]	Jiang Q,Gosselin C,Masseth J.Simulation of hypoid gear lapping[J].Journal of Mechanical Design,2008,130(11):112601.(10 pages)
[2]	Jack M,Mohsen K.Lapping and superfinishing effects on hypoid gears surface finish and transmission errors //Proceedings of the ASME 2007 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference.Las Vegas,Nevada,USA:ASME,2007.
[3]	WEI Bingyang,DENG Xiaozhong,FANF Zongde.The lapping mechanism of hypoid gears[J].Journal of Materials Processing Technology,2009,209(6):3001-3008.
[4]	杨建军,邓效忠,方宗德.螺旋锥齿轮振动研齿系统的拍击响应[J].航空动力学报,2009,24(12):2839-2845. YANG Jianjun,DENG Xiaozhong,FANG Zongde.Rattling response of vibration lapping of sprial bevel gear[J].Journal of Aerospace Power,2009,24(12):2839-2845.(in Chinese)
[5]	王三民,沈允文,董海军.含间隙和时变啮合刚度的弧齿锥齿轮传动系统非线性振动特性研究[J].机械工程学报,2003,39(2):28-32. WANG Sanmin,SHEN Yunwen,DONG Haijun.Nonlinear dynamical characteristics of a spiral bevel gear system with backlash and time-varying stiffness[J].Chinese Journal of Mechanical Engineering,2003,39(2):28-32.(in Chinese)
[6]	杨宏斌,高建平,邓效忠,等.弧齿锥齿轮和准双曲面齿轮的非线形动力学研究[J].航空动力学报,2004,19(1):54-59. YANG Hongbin,GAO Jianping,DENG Xiaozhong,et al.Nonlinear dynamics of spiral bevel gears and hypoid gear drives[J].Journal of Aerospace Power,2004,19(1):54-59.(in Chinese)
[7]	WANG Jun,Lim T C,Li M.Dynamics of a hypoid gear pair considering the effects of time-varying mesh parameters and backlash nonlinearity[J].Journal Sound and Vibration,2007,308(1-2):302-329.
[8]	WANG Jun.Nonlinear time-varying gear mesh and dynamic analysis of hypoid and bevel geared rotor systems .Cincinnati:The University of Cincinnati,2007.
[9]	Krenzer T J.Tooth contact analysis of spiral bevel and hypoid gears under load .Rochester,NY:The Gleason Works,Society of Automotive Engineers,1981.
[10]	魏冰阳,邓效忠,杨建军,等.超声研齿的材料去除机理与试验研究[J].中国机械工程,2006,17(10):995-999. WEI Bingyang,DENG Xiaozong,YANG Jianjun,et al.Study on material removal mechanism and experiments of ultrasonic lapping of gears[J].China Mechanical Engineering,2006,17(10):995-999.(in Chinese)
[11]	李天兴,邓效忠,魏冰阳.基于一维测头准双曲面齿轮齿面偏差的测量[J].中国机械工程,2007,18(8):958-961. LI Tianxing,DENG Xiaozhong,WEI Bingyang.Tooth surface deviation measurement of hypoid gears based on one-dimensional probe[J].China Mechanical Engineering,2007,18(8):958-961.(in Chinese)
[12]	曹雪梅,王军,张海英.弧齿锥齿轮齿面误差检测与实验验证[J].中国机械工程,2009,20(15):1799-1801. CAO Xuemei,WANG Jun,ZHANG Haiying.Geometric error measurement of spiral bevel gears and experimental test[J].China Mechanical Engineering,2009,20(15):1799-1801.(in Chinese)