面齿轮滚磨刀具基蜗杆齿廓奇异点研究

高金忠; 朱如鹏; 李政民卿

面齿轮滚磨刀具基蜗杆齿廓奇异点研究

南京航空航天大学机电学院,南京 210016

基金项目: 国家自然科学基金(50775108,51105194); 航空科技创新基金(08B52004); 南航青年科技创新基金(NS2010129); 南航直升机传动技术专项(NP2011025)

计量
- 文章访问数: 2046
- HTML浏览量: 3
- PDF量: 7
- 被引次数: 0
出版历程
- 收稿日期: 2010-11-17
- 修回日期: 2011-03-11
- 刊出日期: 2011-10-28

Research on singularities of base worm thread surface for hobbing or grinding face gear

College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

摘要

摘要: 为了实现面齿轮的滚磨齿加工,采用包络原理对面齿轮滚磨齿刀具基蜗杆进行设计,并对基蜗杆齿廓曲面的奇异点进行分析.建立了刀具基蜗杆的包络坐标系,给出了刀具基蜗杆产形面方程,推导了刀具基蜗杆齿廓的曲面方程,利用Catia软件对基蜗杆进行了三维建模;推导了基蜗杆曲面的奇异点方程,给出基蜗杆曲面奇异点的计算方法,进行了基蜗杆曲面奇异点的实例计算;分别分析了基蜗杆半径、插齿刀模数、齿数、压力角对基蜗杆曲面奇异点位置的影响.
- 面齿轮 /
- 基蜗杆 /
- 包络法 /
- 蜗杆曲面 /
- 奇异点
Abstract: In order to produce face gear by a hob or grinding worm,a base worm used for hob or grinding worm was designed.In the investigation,a coordinate was established to describe the enveloping process of the worm,the equations describing the worm thread surface were presented,and the three-dimensional (3-D)entity of base worm was created by Catia.The derivation and avoidance of singularities of base worm thread surface was analyzed.A numerical example was given to calculated singularity point.The influence of the base worm radius,the module of shaper,the teeth number and the pressure angle on the singularity point were analyzed,respectively.
- face gear /
- base worm /
- enveloping method /
- worm thread surface /
- singularity point

HTML

参考文献(15)

[1]	Litvin F L,Zhang Y,Wang J C,et al.Design and geometry of face-gear drives[J].Transactions of ASME,Journal of Mechanical Design,1992,114(4):642-647.
[2]	Heath G F,Filler R R,Tan J.Development of face gear technology for industrial and aerospace power transmission .NASA/CR-2002-211320,2002.
[3]	Litvin F L,Wang J C,Bossler R B Jr.,et al.Application of face-gear drives in helicopter transmission[J].ASME Joutnal of Mechanical Design,1994,116(3):672-676.
[4]	Litvin F L,Alfonso F,Claudio Z,et al.Face-gear drive with spur involute pinion:geometry,generation by a worm,stress analysis .NASA/CR-2002-211362,2002.
[5]	Lewicki D G,Heath G F,Filler R R,et al.RDS-21 face-gear surface durability tests .NASA/TM-2007-214970,2007.
[6]	Litvin F L,Alfonso F,Ignacio G P,et al.Face gear drive with helical involute pinion:geometry,generation by a shaper and a worm,avoidance of singularities and stress anaysis .NASA/CR-2005-213443,2005.
[7]	Litvin F L.Theory of pearing .NASA/RP-1212(AVSCOM 88-C-C035),1989.
[8]	Tan J.Apparatus and method for improved precision grinding of face gears:U.S.,5823857 .1998-01-22.
[9]	Litvin F L,Chen Y D,Heath G F,et al.Apparatus for precision grinding face gear:U.S.,6146253 .2000-11-14.
[10]	Heath G F,Bossler R B Jr.Advanced rotorcraft transmission (ART) program final report .NASA/CR-191057,1993.
[11]	Litivin F L,Egelja A,Tan J,et al.Handbook on face gear drives with a spur involute pinion .NASA/CR-2000-209909,2000.
[12]	朱如鹏,潘升材,高德平.面齿轮传动的研究现状与发展[J].南京航空航天大学学报,1997,29(3):358-361. ZHU Rupeng,PAN Shengcai,GAO Deping.Current state and development of research on face gear drive[J].Journal of Nanjing University of Aeronautics & Astronautics,1997,29(3):358-361.(in Chinese)
[13]	李政民卿,朱如鹏.面齿轮滚磨刀具基蜗杆研究[J].机械科学与技术,2009,28(1):99-101. LI Zhengminqing,ZHU Rupeng.A study of worm of hobbing or grinding wheel for face gear[J].Mechanical Science and Technology for Aerospace Engineering,2009,28(1):99-101.(in Chinese)
[14]	王延忠,吴灿辉,葛旭阳,等.面齿轮滚刀基本蜗杆的设计方法[J].北京航空航天大学学报,2009,35(2):166-169. WANG Yanzhong,WU Canhui,GE Xuyang,et al.Basalworm designing method of face-gear hob[J].Journal of Beijing University of Aeronautics and Astronautics,2009,35(2):166-169.(in Chinese)
[15]	郭辉,赵宁,方宗德,等.基于接触有限元的面齿轮传动弯曲强度研究[J].航空动力学报,2008,23(8):1438-1422. GUO Hui,ZHAO Ning,FANG Zongde,et al.Research on bending strength of face gear transmission based on contact finite element method[J].Journal of Aerospace Power,2008,23(8):1422-1438.(in Chinese)