前板结构对低滞后刷式密封性能影响分析

迟佳栋; 王之栎

前板结构对低滞后刷式密封性能影响分析

北京航空航天大学机械工程及自动化学院,北京 100191

计量
- 文章访问数: 1505
- HTML浏览量: 2
- PDF量: 526
- 被引次数: 0
出版历程
- 收稿日期: 2011-08-22
- 刊出日期: 2012-08-28

Analysis of front plate's effect on low hysteresis brush seal

School of Mechanical Engineering and Automation, Beijing University Aeronautics and Astronautics,Beijing 100191,China

摘要

摘要: 针对不同前板结构的低滞后刷式密封,采用多孔介质模型,进行流场计算,对计算得到的上游刷丝压力、速度分布、刷丝上游靠近跑道区域的湍流动能以及刷式密封泄漏量进行分析,讨论对于低滞后刷式密封的性能的影响.分析表明:前板结构对上游刷丝压力、轴向速度分布以及刷式密封泄漏量无明显影响,对上游刷丝径向速度分布影响较大;无前板及过长前板结构,刷封上游靠近跑道区域湍流动能较大,前板开孔可降低刷丝上游靠近跑道区域的湍流动能,减弱刷丝扰动的趋势.
- 刷式密封 /
- 前板 /
- 低滞后 /
- 多孔介质 /
- 刷丝扰动
Abstract: Aimed at different kinds of low hysteresis brush seals,computed them with porous medium model,and analyzed the pressure and velocity on upstream side of bristles,turbulence kinetic energy at the front and low part of bristles,discussed the effect of front plate on low hysteresis brush seals.The result indicates that front plate does not have obvious effect on upstream bristles' pressure,axial velocity and leakage of brush seals,but varies radial velocity on upstream bristles behind different kinds of front plate;the turbulence kinetic energy at the upstream and low part of bristles of the brush seal without front plant or with front plate too long is very big,the brush seal has front plate with holes got smaller turbulence kinetic energy at the upstream and low part of bristles than the other kinds of brush seal,and gets smaller bristle disturbance effect.
- brush seal /
- front plate /
- low hysteresis /
- porous medium /
- bristle disturbance

HTML

参考文献(15)

[1]	Lelli D,Chew J W,Cooper P.Combined three-dementional fluid dynamic and mechanical modeling of brush seals[J].Journal of Turburbomachinery,2006,128(1):188-195.
[2]	Prior R,Short J,Basu P.Brush seal wear model .AIAA 1998-3170,1998.
[3]	Chew J W,Lapworth B L,Millener P J.Mathematical modeling of brush seals[J].Int.J.Heat Fluid Flow,1995,16(6):493-500.
[4]	Guardino C,Chew J W.Numerical simulation of three-dimensional bristle bending in brush seals[J].ASME Journal of Engineering for Gas Turbines and Power,2005,127(7):583-591.
[5]	刘占生,叶建槐.刷式密封接触动力学特性研究[J].航空动力学报,2002,17(5):635-640. LIU Zhansheng,YE Jianhuai.Research on structural dynamic characteristics of brush seals[J].Journal of Aerospace Power,2002,17(5):635-640.(in Chinese)
[6]	王之栎,梁小峰,宋飞,等.低滞后刷式密封数值分析[J].北京航空航天大学学报,2008,34(9):1080-1083. WANG Zhili,LIANG Xiaofeng,SONG Fei,et al.Low hysteresis brush seal numerical simulations[J].Journal of Beijing University of Aeronautics and Astronautics,2008,34(9):1080-1083.(in Chinese)
[7]	李理科,王之栎,宋飞,等.刷式密封温度场数值研究[J].航空动力学报,2010,25(5):1018-1024. LI Like,WANG Zhili,SONG Fei,et al.Numerical investigation of temperature field in brush seals[J].Journal of Aerospace Power,2010,25(5):1018-1024.(in Chinese)
[8]	Tseng T W,Short J F,Steinetz B M.Development of a low hysteresis brush seal for modern engine application .AIAA 1999-2683,1999.
[9]	Aksit M F,Tichy J A.Wear of brush seals:background and new modeling approach[J].Tribol Trans,1998,41(3):368-374.
[10]	Wood P E,Jones T V.A test facility for the measurement of torques at the shaft to seal interface in brush seals[J].Journal of Engineering for Gas Turbines and Power,1999,121(1):160-166.
[11]	Zhao H,Stango R J.Role of distributed interbristle friction force on brush seal hysteresis[J].ASME Journal of Tribology,2007,129(1):199-204.
[12]	CHI Jiadong,WANG Zhili,LI Like.Numerical simulation and analysis of low hysteresis brush seals[J].Advanced Materials Research,2012,452/453:1455-1459.
[13]	Dogu Y,Aksit M F.Effects of geometry on brush seal pressure and flow fields Part Ⅰ:front plate configurations[J].Journal of Turbomachinery,2006,128(2):367-378.
[14]	张兆顺,崔桂香,许春晓.湍流的理论与模拟[M].北京:清华大学出版社,2005.
[15]	王福军.计算流体动力学分析——CFD软件的原理与应用[M].北京:清华大学出版社,2004.