齿形几何参数对直通篦齿封严泄漏特性影响的正交实验

杜发青; 吉洪湖; 帅海山; 张勃; 王丁; 陆海鹰; 邓明春

齿形几何参数对直通篦齿封严泄漏特性影响的正交实验

1.
南京航空航天大学能源与动力学院, 南京 210016
2.
中国航空工业集团公司沈阳发动机设计研究所, 沈阳 110015

计量
- 文章访问数: 1358
- HTML浏览量: 2
- PDF量: 868
- 被引次数: 0
出版历程
- 收稿日期: 2012-04-27
- 刊出日期: 2013-04-28

Orthogonal experiment of effect of fin geometrical parameters on leakage of straight-through labyrinth seals

1.
College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2.
Shenyang Engine Design and Research Institute, Aviation Industry Corporation of China, Shenyang 110015, China

摘要

摘要: 针对影响直通篦齿泄漏特性的6个主要几何参数(齿宽、封严间隙、齿高、齿距、前倾角和后倾角)及其常用的取值范围,依据正交原理设计了25个篦齿实验件,实验研究了其对泄漏特性的影响.结果表明:上述参数对流量系数的影响趋势有明显的区别;根据实验结果推断:封严效果最好的齿形结构为齿宽取0.1mm、封严间隙取0.3mm、齿高取3mm、齿距取9mm、前倾角取0°、后倾角取15°;上述参数在实验范围内的变化对流量系数影响程度的主次排序为:齿距→封严间隙→后倾角→齿宽→齿高→前倾角,齿距影响非常显著,封严间隙影响显著,后倾角和齿宽有一般影响,齿高和前倾角影响不显著.
- 直通篦齿 /
- 几何参数 /
- 泄漏 /
- 流量系数 /
- 正交
Abstract: An orthogonal experiment was made to study the influence of the geometry parameters of straight-through labyrinth seals on sealing characteristics.The geometry parameters studied include the fin tip thickness,seal clearance,fin height,fin pitch,fin front inclined angle and rear inclined angle.The experiment was made with 25 models that were designed according to the orthogonal test method.The results show that various parameters have different influences on discharge coefficient.The best combination of various geometry parameters for sealing in the test range is that fin tip thickness takes 0.1mm,seal clearance takes 0.3mm,fin height takes 3 mm,fin pitch takes 9 mm,fin front inclined angle takes 0 degree and rear inclined angle takes 15 degree .The rank of importance of each parameter's variation from its maximum to minimum value on sealing characteristics is fin pitch,seal clearance,rear inclined angle,fin tip thickness,fin height,fin front inclined angle.Fin pitch is the most important parameter,seal dearance is less important than fin pitch,rear inclined angle and fin tip thickness have certain impact on the sealing characteristics,while fin height and fin front inclined angle have little influence on it.
- straight-through labyrinth /
- geometrical parameter /
- leakage /
- discharge coefficient /
- orthogonal

HTML

参考文献(15)

[1]	刘卫华,林丽,朱高涛.迷宫密封激励的研究现状及其展望[J].流体机械,2007,35(2):35-39. LIU Weihua,LIN Li,ZHU Gaotao.Current situation of the research and development of the mechanism of labyrinth seal[J].Fluid Machinery,2007,35(2):35-39.(in Chinese)
[2]	Sturgess G J.Application of CFD to gas turbine engine secondary flow system [R].AIAA-SS-3203,1988.
[3]	Steinetz B M,Hendricks R C.Engine seal technology requirements to meet NASA's advanced subsonic technology program goals [R].AIAA-94-2698,1994.
[4]	Steinetz B M,Hendricks R C.Advanced seal technology role in meeting next generation turbine engine goal [R].NASA/TM-1988-206961,1988.
[5]	Demko J A,Morrison G L,Rhode D L.Effect of shaft rotation on the incompressible flow in a labyrinth seal[J].Journal of Propulsion and Power,1990,6(2):171-176.
[6]	Waschka W,Witting S,Kim S.Influence of high rotational speeds on the heat transfer and discharge coefficients in labyrinth seals[J].ASME Paper 90-GT-330,1990.
[7]	纪国剑,吉洪湖.旋转状态下篦齿-蜂窝结构封严特性研究[J].工程热物理学报,2006,27(1):161-164. JI Guojian,JI Honghu.Investigation of sealing characteristics of labyrinth-honeycomb seal under rotating condition[J].Journal of Engineering Thermophysics,2006,27(1):161-164.(in Chinese)
[8]	纪国剑,吉洪湖,曹广州.旋转对小间隙篦齿-蜂窝结构封严特性的影响[J].南京航空航天大学学报,2008,40(2):142-145. JI Guojian,JI Honghu,CAO Guangzhou.Effect of rotating speed on leakage characteristics of labyrhth honeycomb seal with small clearance[J].Journal of Nanjing University of Aeronautics and Astronautics,2008,40(2):142-145.(in Chinese)
[9]	塔鲁达纳斯基.非接触密封:间隙密封与迷宫密封的原理和应用[M].北京:机械工业出版社,1986.
[10]	Denecke J,Schramm V,Kim S,et al.Influece of rub-grooves on labyrinth seal leakage[J].Journal of Turbomachinery,2003,125:387-393.
[11]	黄晓光,吴丁毅.直通式篦齿密封内部流动和换热实验台设计及流场分布的实验研究[J].流体机械,1999,27(5):6-9. HUANG Xiaoguang,WU Dingyi.The design of test bench for investigating on flow and heat characteristics and the experimental investigation on flow field distribution of straight labyrinth seal[J].Fluid Machinery,1999,27(5):6-9.(in Chinese)
[12]	黄晓光,吴丁毅.直通篦齿封严篦齿内部流动和换热的实验研究[J].推进技术,1999,20(5):80-85. HUANG Xiaoguang,WU Dingyi.Design of experiment platform and investigation of flow field and heat transfer in straight labyrinth seal[J].Journal of Propulsion Technology,1999,20(5):80-85.(in Chinese)
[13]	Wittig S L K,Dorr L,Kim S.Scaling effects on leakage losses in labyrinth seals[J].Journal of Engineering for Power,1983,105(2):305-309.
[14]	纪国剑,吉洪湖.直通篦齿封严结构压损规律和临界特性的研究[J].航空动力学报,2008,23(3):415-420. JI Guojian,JI Honghu.Numerical and experimental investigation of pressure loss and critical sealing characteristics of straight-through labyrinth seals[J].Journal of Aerospace Power,2008,23(3):415-420.(in Chinese)
[15]	何长征,张永福,韦红旗.正交实验设计及其在锅炉燃烧调整中的应用[J].能源研究与利用,2004,4(6):40-43. HE Changzheng,ZHANG Yongfu,WEI Hongqi The orthogonal experiment design and the application in combustion regulation test on the boiler[J].Energy Research and Utilization,2004,4(6):40-43.(in Chinese)