基于CFD分析的二冲程发动机直喷燃烧室方案设计
Design of combustion chamber program of two-stroke direct injection spark ignition engine based on the CFD
-
摘要: 采用三维实体建模软件UG对此二冲程发动机的燃烧室进行直喷化设计,并利用三维CFD仿真软件Fluent对直喷燃烧室的缸内流场进行CFD仿真与分析.分析结果显示:当燃烧室高度从32mm降为24mm,以及活塞顶面与缸盖底面距离从7mm降为3mm时,压缩过程中的反滚流结构消失,扫气效率从87%升高到91%.模拟结果为进一步优化燃烧室结构提供了较好依据.Abstract: The combustion chamber of the two-stroke engine was modified to a direct-injection combustion chamber by using 3-D entity modeling software UG, then 3-D CFD software Fluent was used to simulate and analyze the in-cylinder fluid structure. The results show that, when the height of combustion chamber is reduced to 24mm from 32mm, and the distance from the top of piston to the bottom of cylinder head is reduced to 3mm from 7mm, the roll back flow structure in the process of compression disappears, and the scavenging efficiency increases from 87% to 91%. The simulation results provide a good basis for further structure optimization of combustion chamber.
-
[1] Blair G P, Drouin F M M.Relationship between discharge coefficients and accuracy of engine simulation[R].Society of Automotive Engineers (SAE) 962527, 1996. [2] Marek W, Mitianiec W.Reduction of exhaust gas emission in a two-stroke engine with pneumatic fuel injection[R].Society of Automotive Engineers (SAE) 2168, 2002. [3] Drecq D, Benteyn P E.Engine scavenging optimization[R].Society of Automotive Engineers (SAE) 1843, 2002. [4] Merker G P, Gerstle M.Evalution on two stroke engines scavenging models[R].Society of Automotive Engineers (SAE) 970358, 1997. [5] Bergman M, Gustafsson R U K.Scavenging system lay-out of a 25cc two-stroke engine intended for stratified sca-venging[R].Society of Automotive Engineers (SAE) 1840, 2002. [6] Winkler F, Schmidt S, Schoegl O.Development of a combustion process for a high performance 2-stroke engine with high pressure direct injection[R].Society of Automotive Engineers (SAE) 2942, 2004. [7] Pontoppidan R, Gaviani R.Optimization by CFD simulation of spray formation parameters to adapt direct injection high-pressure fuel injectors to high-speed SI-engines[R].Society of Automotive Engineers (SAE) 0593, 2004. [8] Cathcar G, Dickson G.The application of air-assist direct injection for spark-ignited heavy fuel 2-stroke and 4-stroke engines[R].Society of Automotive Engineers (SAE) 6580, 2005. [9] Mc Elligott S, Douglas R, Kee R J.Stratified scavenging applied to a small capacity two-stroke scooter for the reduction of fuel consumption and emissions[R].Society of Automotive Engineers (SAE) 3271, 1999. [10] 陈登.二冲程缸内直喷汽油机扫气和喷油过程的多维数值模拟[D].天津:天津大学, 2005. CHEN Deng.Multi-dimensional numerical simulation of scavenging and injection process of 2-stroke direct injection engine[D].Tianjin:Tianjin University, 2005.(in Chinese) [11] Cunningham G, Kee R J.CFD prediction of crankcase flow regimes in a crankcase scavenged 2-stroke engine[R].Society of Automotive Engineers (SAE) 970361, 1997. [12] 蒋炎坤, 钟毅芳, 罗马吉.二冲程发动机扫排气道-缸内系统三维瞬态数值模拟研究[J].内燃机学报, 2001, 19(2):159-164. JIANG Yankun, ZHONG Yifang, LUO Maji.Research of three dimensional transient numerical simulation of scavenging-exhaust duct and cylinder system of two-stroke[J].Transactions of Csice, 2001, 19(2):159-164.(in Chinese) [13] 刘兵, 杨迪.二冲程汽油机扫气过程多维数值模拟[J].西安交通大学学报, 1999, 33(1):69-72. LIU Bing, YANG Di.Multi-dimensional numerical simulation of scavenging process of two stroke gasoline engine[J].Journal of Xi'an Jiaotong University, 1999, 33(1):69-72.(in Chinese) [14] Raghunathan B D, Kenny R G.CFD simulation and validation of the flow within a motored two-stroke engine[R].Society of Automotive Engineers(SAE) 970359, 1997. [15] 由丽卿, 毛华永, 黄宜谅.二冲程发动机扫气过程试验方法的研究[J].内燃机工程, 1996, 17(3):58-65. YOU Liqing, MAO Huayong, HUANG Yiliang.Research of test method of scavenging process of two-stroke gasoline engine[J].Internal Combustion Engine Engineering, 1996, 17(3):58-65.(in Chinese)
点击查看大图
计量
- 文章访问数: 1318
- HTML浏览量: 2
- PDF量: 942
- 被引次数: 0