涡轮盘腔轴向封严流动的数值研究

张晶辉; 马宏伟

doi:10.13224/j.cnki.jasp.2014.04.025

涡轮盘腔轴向封严流动的数值研究

doi: 10.13224/j.cnki.jasp.2014.04.025

北京航空航天大学能源与动力工程学院航空发动机气动热力国家级重点实验室,北京 100191

基金项目:

北京航空航天大学基本科研业务费-博士研究生创新基金(YWF-13-A01-17)

国家自然科学基金(51161130525)

详细信息

作者简介:
张晶辉(1986-),男,河南洛阳人,博士生,主要从事叶轮机械内复杂流动研究.

中图分类号: V231.3
计量
- 文章访问数: 1345
- HTML浏览量: 1
- PDF量: 815
- 被引次数: 0
出版历程
- 收稿日期: 2013-12-04
- 刊出日期: 2014-04-28

Numerical investigation of axial seal flow in turbine cavity

National Key Laboratory of Science and Technology on Aero-Engine Aero-thermodynamics,School of Energy and Power Engineering,Beijing University of Aeronautics and Astronautics,Beijing 100191,China

摘要

摘要: 利用数值方法研究了轴向封严结构内的燃气入侵与封严流动.研究表明:由于封严间隙处流场参数梯度较大,封严面非匹配网格影响了数值传递从而造成封严效率数值结果偏高.定常数值模拟结果低估了导叶下游静压的周向不均匀性,同时没有考虑转静干涉,所得到的封严效率较非定常结果要高.非定常计算得到的导叶下游静压周向分布与试验结果符合较好,在盘腔子午面内形成3个涡核结构,引导静盘壁面流体流向动盘以补充动盘泵效应所需流量.封严间隙内存在旋转的燃气入侵与出流结构,燃气入侵伴随较大的切向速度,封严间隙内的封严间隙涡对封严效率有积极影响,封严面上径向速度的瞬时值为时均值的3倍以上.燃气入侵受到导叶尾缘周向静压分布和转子旋转的共同影响.
- 轴向封严结构 /
- 轮缘封严机理 /
- 燃气入侵 /
- 非定常 /
- 涡轮盘腔
Abstract: Hot gas ingestion and seal flow in axial seal configuration was investigated numerically. The results show that the unmatched mesh strategy on sealing surface affects the numerical transfer because of bigger gradient of parameters which lead to higher sealing effectiveness. The steady simulation underestimates the circumference pressure unevenness downstream the vane and ignores the interaction of stator and rotor; as a result the sealing effectiveness is much bigger than unsteady simulation. The unsteady results agree with the experimental date very well. Three vortexes appear in the cavity meridian plane, and guide the flow near static disc to rotor disc for supplement the flow required by disc entrainment. Rotating hot gas ingestion and egress structures appear in seal clearance, and the ingestion flow has bigger tangential velocity. The seal clearance vortexes in seal clearance have positive effects on sealing efficiency.The transient radial velocity is 3 times bigger than time-averaged value on sealing surface. The hot gas ingestion is affected by the circumferential distribution of static pressure downstream of vane and rotor rotation.
- axial seal configuration /
- rim seal mechanism /
- hot gas ingestion /
- unsteady /
- turbine cavity

HTML

参考文献(18)

[1]	Johnson B V,Mack G J,Paolillo R E,et al.Turbine rim seal gas path flow ingestion mechanisms .AIAA 94-2703,1994.
[2]	Coren D D,Atkins N R,Turner J R,et al.An advanced multi-configuration stator well cooling test facility .ASME Paper GT2010-23450,2010.
[3]	Hills N J,Chew J W,Turner A B.Computational and mathematical modeling of turbine rim seal ingestion[J].Journal of Turbomachinery,2002,124(2):306-315.
[4]	Gentilhomme O,Hills N J,Turner A B,et al.Measurements and analysis of ingestion through a turbine rim seal[J].Journal of Turbomachinery,2003,125(3):505-512.
[5]	Roy R P,Zhou D W,Ganesan S,et al.The flow field and main gas ingestion in a rotor-stator cavity .ASME Paper GT2007-27671,2007.
[6]	Chew J W.Developments in turbomachinery internal air systems[J].Proceedings of the Institution of Mechanical Engineers:Part C Journal of Mechanical Engineering Science,2009,223(1):189-234.
[7]	Jakoby R,Zierer T,Lindblad K,et al.Numerical simulation of the unsteady flow field in an axial gas turbine rim seal configuration .ASME Paper GT2004-53829,2004.
[8]	Cao C,Chew J W,Millington P R,et al.Interaction of rim seal and annulus flow in an axial flow turbine[J].Journal of Engineering for Gas Turbines and Power,2004,126(4):786-793.
[9]	Schuepbach P,Abhari R S,Rose M G,et al.Effects of suction and injection purge-flow on the secondary flow structures of a high-work turbine .ASME Paper GT2008-50471,2008.
[10]	Steve J,Julie L,Guy D,et al.Simulations of flow ingestion and related structures in a turbine disk cavity .ASME Paper GT2010-22729,2010.
[11]	OMahoney T S D,Hills N J,Chew J W,et al.Large-eddy simulation of rim seal ingestion .ASME Paper GT2010-22962,2010.
[12]	Rabs M,Benra F K,Dohmen H J,et al.Investigation of flow instabilities near the rim cavity of a 1.5 stage gas turbine .ASME Paper GT2009-59965,2009.
[13]	Green T,Turner A B.Ingestion into the upstream wheelspace of an axial turbine stage[J].Journal of Turbomachinery,1994,116(2):327-332.
[14]	Wang C Z,Johnson B V,Jong F D,et al.Comparison of flow characteristics in axial-gap seals for close and wide-spaced turbine stages .ASME Paper GT2007-27909, 2007.
[15]	孙纪宁,罗翔,刘金楠,等.体积分数法测量几种转静系中的最小封严流量[J].航空动力学报,2012,27(5):981-985. SUN Jining,LUO Xiang,LIU Jinnan,et al.Volume fraction technique for measuring the minimum value of mass flow in turbine rotor-stator disk cavities[J].Journal of Aerospace Power,2012,27(5):981-985.(in Chinese)
[16]	周昆原,罗翔,徐国强.旋转诱导燃气入侵的数值模拟[J].航空动力学报,2011,26(12):2704-2709. ZHOU Kunyuan,LUO Xiang,XU Guoqiang.Numerical simulation of rotationally-induced ingress through turbine rim seals[J].Journal of Aerospace Power,2011,26(12):2704-2709.(in Chinese)
[17]	高庆,陶加银,宋立明,等.涡轮轮缘密封封严效率的数值研究[J].西安交通大学学报,2013,47(5):12-17. GAO Qing,TAO Jiayin,SONG Liming,et al.Numerical investigation on the sealing efficiency of the turbine rim seal[J].Journal of Xian Jiaotong University,2013,47(5):12-17.(in Chinese)
[18]	Bohn D E,Decker A,Ohlendorf N,et al.Influence of an axial and radial rim seal geometry on hot gas ingestion into the upstream cavity of a 1.5-stage turbine .ASME Paper GT2006-90453,2006.