基于多孔介质模型的指尖密封泄漏流动分析

白花蕾; 王伟; 张振生; 胡广阳

doi:10.13224/j.cnki.jasp.2016.06.004

基于多孔介质模型的指尖密封泄漏流动分析

doi: 10.13224/j.cnki.jasp.2016.06.004

中国航空工业集团公司沈阳发动机设计研究所, 沈阳 110015

详细信息

作者简介:
白花蕾(1983-),女,陕西渭南人,工程师,硕士,主要从事航空发动机密封技术设计和试验研究.

中图分类号: V231;TB42
计量
- 文章访问数: 943
- HTML浏览量: 2
- PDF量: 734
- 被引次数: 0
出版历程
- 收稿日期: 2014-10-07
- 刊出日期: 2016-06-28

Analysis of leakage flow through finger seal based on porous medium

Shenyang Engine Design and Research Institute, Aviation Industry Corporation of China, Shenyang 110015, China

摘要

摘要: 将指尖密封处理为多孔介质,把压力梯度作为多孔介质动量方程中的源项,根据试验结果确定了源项中的系数,结合指尖密封的结构参数提出了用于指尖密封泄漏的多孔介质模型,利用该模型计算结果与试验结果吻合较好,证明利用该模型模拟指尖密封泄漏是可行的.流场计算结果表明:指尖密封与转子接触部分的孔隙率对泄漏影响比较大,指尖密封的承压部分主要为后挡板内径以下区域.
- 密封装置 /
- 指尖密封 /
- 多孔介质 /
- 泄漏流动 /
- 数值模型
Abstract: The finger seal was treated as porous medium. The pressure gradient was regarded as the source term of momentum equation. The coefficient in source term was confirmed by experimental results. A porous medium model for the leakage through finger seal was put forward by combining with the finer seal configuration. The computational results showed a good agreement with the experimental results, the model was proved to be practicable for simulating the leakage of finger seal. Flow field computational results show that the influence of the porosity of finger contact pad on leakage is great, and the pressure grads in the finger seal are mainly distributed below the inner diameter of aft cover plate.
- seal device /
- finger seal /
- porous medium /
- leakage flow /
- numerical model

HTML

参考文献(21)

[1]	Arora G K,Proctor M P,Steinetz B M,et al.Pressure balanced,low hysteresis,finger seal test results[R].Los Angeles,USA:35th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit,1999.
[2]	Proctor M P,Delgado I R.Leakage and power loss test results for competing turbine seals[R].NASA-2004-213049,2004.
[3]	Steinetz B M,Hendricks R C.Advanced seal technology in meeting next generation turbine engine goal[R].NASA/TM-1998-06961,1998.
[4]	Steinefz B M,Hendricks R C.Engine seal technology requirements to meet NASA's advanced subsonic technology program goals[R].AIAA 94-2698,1994.
[5]	苏华,陈国定.指尖密封型线形成的研究[J].机械科学与技术,2003,22(6):876-878. SU Hua,CHEN Guoding.Study of the shape-curve of finger seal[J].Mechanical Science and Technology,2003,22(6):876-878.(in Chinese)
[6]	Braun M J,Steinetz B M.Two and three dimensional numerical experiment s representing two limiting cases of an in line pair of finger seal components[J].International Journal of Rotating Machinery,2003,9(3):171-179.
[7]	Hendricks R C,O'Halloran B,Arora G,et al.Advances in contact sealing[R].NASA CP-3282,1994.
[8]	Braun M J,Hendricks R C,Canacci V A.Non-intrusive qualitative and quantitative flow characterization and bulk flow model for brush seals[R].Nagoya:Japan Incorporated Tribology Conference,1990.
[9]	Hendricks R C,Schlumberger S,Braun M J,et al.A bulk flow model of a brush seal system[R].ASME Paper 91-GT-325,1991.
[10]	王旭,张文平,来亮,等.指尖密封泄漏流动的数值仿真分析[J].航空动力学报,2005,20(4):590-594. WANG Xu,ZHANG Wenping,LAI Liang,et al.Numerical simulation and analysis of a finger seal leakage flow[J].Journal of Aerospace Power,2005,20(4):590-594.(in Chinese)
[11]	李国见,李建华,陈国定,等.动压型指尖密封泄漏特性的分析[J].科学技术与工程,2007,7(13):3157-3159. LI Guojian,LI Jianhua,CHEN Guoding,et al.Analysis to the leakage patterns of hydrodynamic pressure finger seal[J].Science Technology and Engineering,2007,7(13):3157-3159.(in Chinese)
[12]	马晓琳,陈国定.基于等效模型的流体动压指尖密封动力学及泄漏量分析[J].航空学报,2008,29(5):1356-1363. MA Xiaolin,CHEN Guoding.Dynamics and leakage analysis of padded finger seal based on equivalent model[J].Acta Aeronautica et Astronautica Sinica,2008,29(5):1356-1363.(in Chinese)
[13]	张延超,陈国定,申晓龙.指尖密封动态性能分析与泄漏量计算[J].航空学报,2009,30(11):2193-2199. ZHANG Yanchao,CHEN Guoding,SHEN Xiaolong.Analysis of dynamic performance and leakage for finger seal[J].Acta Aeronautica et Astronautica Sinica,2009,30(11):2193-2199.(in Chinese)
[14]	白花蕾,吉洪湖,纪国剑,等.指式密封泄漏特性的试验研究[J].航空动力学报,2009,24(3):532-536. BAI Hualei,JI Honghu,JI Guojian,et al.Experimental investigation on leakage characteristics of finger seal[J].Journal of Aerospace Power,2009,24(3):532-536.(in Chinese)
[15]	Chew J W,Hogg S I.Porosity modeling of brush seals[J].Journal of Tribology,1997,119(4):769-775.
[16]	黄学民,史伟,王洪铭.刷式密封中泄漏流动的多孔介质数值模型[J].航空动力学报,2000,15(1):55-58. HUANG Xuemin,SHI Wei,WANG Hongming.Porous medium leakage flow model of brush seal[J].Journal of Aerospace Power,2000,15 (1):55-58.(in Chinese)
[17]	曹广州,吉洪湖,袁艳平.模拟刷式封严泄漏流动的多孔介质模型[J].航空动力学报,2008,23(3):443-447. CAO Guangzhou,JI Honghu,YUAN Yanping.A porous medium model for simulating leakage flows through brush seals[J].Journal of Aerospace Power,2008,23(3):443-447.(in Chinese)
[18]	Fluent Incorporated.FLUENT user's guide[M].[S.l.]:Fluent Incorporated,2003.
[19]	林瑞泰.多孔介质传热传质引论[M].北京:科学出版社,1995.
[20]	潘阳,许国良,中山顕,等.计算传热学理论及其在多孔介质中的应用[M].北京:科学出版社,2011.
[21]	Cie Dślewicz S M.CFD-simulations for advanced turbomachinery sealing technologies:brush seals[D].Vienna:Mechanical Engineering Technical University,2004.