指尖封严磨损特性及其对泄漏影响的试验

杜春华; 吉洪湖; 胡娅萍; 罗健; 马丹; 汤丽萍; 廖凯

doi:10.13224/j.cnki.jasp.2017.01.008

指尖封严磨损特性及其对泄漏影响的试验

doi: 10.13224/j.cnki.jasp.2017.01.008

1.
南京航空航天大学能源与动力学院,南京 210016
2.
中国航空发动机集团有限公司商用航空发动机有限责任公司,上海 200241

基金项目: 国家自然科学基金(51106072);航空科学基金(2014ZB2027)

计量
- 文章访问数: 920
- HTML浏览量: 1
- PDF量: 464
- 被引次数: 0
出版历程
- 收稿日期: 2015-04-12
- 刊出日期: 2017-01-28

Experiment of wearing characteristics and its effect on leakage of finger seal

摘要

摘要: 对间隙、过渡、过盈3种配合的指尖封严的磨损特性及其对泄漏的影响进行了试验研究,分析了不同配合状态下封严件与转子的磨损现象、磨损长度以及封严泄漏系数的分布.试验结果表明:封严磨损随封严与转子相对滑动距离增大而增加；间隙配合状态下,封严出现局部磨损,磨损及其对泄漏的影响主要发生试验初始阶段；过盈配合时,封严件整体均出现磨损,且磨损发生在整个试验阶段,磨损对泄漏的影响在初始阶段较大、之后逐渐减小；封严的间隙越小(过盈量越大),磨损对泄漏影响越大.
- 指尖封严 /
- 磨损特性 /
- 泄漏 /
- 间隙配合 /
- 过盈配合
Abstract: Wearing characteristics of rotor and its effect on leakage of finger seals under three different kinds of fit, namely clearance fit, transition fit and interference fit, were experimentally investigated. The wearing of the rotor, wearing length of seal and distribution of leakage coefficient were analyzed. The results show that the wearing is severer when the sliding distance between the seals and the rotor increases. For finger seal with clearance fit, the seal is partially worn and the wear and its effect on the leakage mainly occur at the beginning of the experiment. For finger seal with interference fit, the whole seal is worn and the wear occurs throughout the experiment. The effect of wearing on the leakage is notable at the beginning and then is gradually decreased. The effect of wearing on leakage is greater when the clearance is smaller or the interference is larger.
- finger seal /
- wearing characteristics /
- leakage /
- clearance fit /
- interference fit

HTML

参考文献(18)

[1]	Heydrich H.Bidirectional finger:US,5031922［P］.1991-07-16.
[2]	Mackay C G.Laminated finger seal:US,5042823［P］.1991-08-27.
[3]	Johnson M C.Laminated finger seal with logarithmic curvature:US,5108116［P］.1992-04-28.
[4]	Arora G K.Noncontacting finger seal with hydrodynamic foot portion:US,5755445［P］.1998-05-26.
[5]	Arora G K.Dual pressure balanced noncontacting finger seal:US,6364316［P］.2002-04-02.
[6]	克拉盖尔斯基.摩擦磨损计算原理［M］.北京:机械工业出版社,1982.
[7]	温诗铸,黄平.摩擦学原理［M］.北京:清华大学出版社,2002.
[8]	Archard J F.Contact and rubbing of flat surfaces［J］.Journal of Applied Physics,1953,24(8):981-988.
[9]	Archard J F.Wear theory and mechanism［R］.New York:ASME Unite Engineering Center,1980.
[10]	苏华.指尖密封结构和性能的设计分析与试验研究［D］.西安：西北工业大学,2006. SU Hua.Structural design and performance analysis and tests of finger seal［D］.Xian:Northwestern Polytechnical University,2006.(in Chinese)
[11]	张延超,陈国定,杨美玲.指尖封严结构参数与泄漏量和磨损性能的灰关系分析［J］.中国机械工程,2008,19(18):2147-2151. ZHANG Yanchao,CHEN Guoding,YANG Meiling.Grey associative analysis of design parameters to leakage and wear performance for finger seal［J］.China Mechanical Engineering,2008,19(18):2147-2151.(in Chinese)
[12]	王红艳,陈国定,张延超.指尖密封性能与结构参数的灵敏度分析［J］.润滑与密封,2008,33(10):11-16. WANG Hongyan,CHEN Guoding,ZHANG Yanchao.Sensitivity analysis of finger seal performances and construction parameters［J］.Lubrication Engineering,2008,33(10):11-16.(in Chinese)
[13]	李二圣,陈国定.一种低迟滞低磨损的指尖密封型线构形的研究［J］.航空动力学报,2008,23(4):759-764. LI Ersheng,CHEN Guoding.Study on a new shapecurve of finger seal with lowhysteresis and lowwear［J］.Journal of Aerospace Power,2008,23(4):759-764.(in Chinese)
[14]	宗兆科,苏华.圆弧型指尖密封的几何构型特征及结构优化［J］.航空学报,2010,31(2):393-399. ZONG Zhaoke,SU Hua.Geometric feature and structure optimization of arc finger seal［J］.Acta Aeronautica et Astronautica Sinica,2010,31(2):393-399.(in Chinese)
[15]	Proctor M P,Kumar A,Delgado I R.Highspeed,hightemperature finger seal result［R］.NASA/TM2002211589,2002.
[16]	Proctor M P,Delgado I R.Leakage and power loss test results for competing turbine seals［R］.NASA2004213049，2004.
[17]	王旭.流体静压型指尖密封的理论与试验研究［D］.哈尔滨:哈尔滨工程大学,2006. WANG Xu.A theoretical and experimental study for hydrostatic finger seal［D］.Harbin:Harbin Engineering University,2006.(in Chinese)
[18]	杜春华,吉洪湖,胡娅萍,等.指尖封严的转子轴心轨迹与泄漏特性实验研究［J］.航空动力学报,2016,31(11):2575-2584. DU Chunhua,JI Honghu,HU Yaping,et al.Experimental investigation on the axis locus of rotor and leakage characteristics of finger seal［J］.Journal of Aerospace Power,2016,31(11):2575-2584.(in Chinese)