气体动压止推轴承性能及实验

侯安平; 林蓬成; 王锐; 李剑雄; 胡斌

doi:10.13224/j.cnki.jasp.2018.06.025

气体动压止推轴承性能及实验

doi: 10.13224/j.cnki.jasp.2018.06.025

1.
北京航空航天大学能源与动力工程学院, 北京 100191
2.
中国航天科技集团有限公司北京航天动力研究所, 北京 100071

计量
- 文章访问数: 869
- HTML浏览量: 65
- PDF量: 502
- 被引次数: 0
出版历程
- 收稿日期: 2016-12-07
- 刊出日期: 2018-06-28

Performance of air-dynamic lubrication thrust bearing and experiment

摘要

摘要: 为了研究气体动压箔片止推轴承的动力特性，建立了刚性表面气体动压止推轴承模型，采用数值计算的方法找出了不同结构参数、转速等对刚性表面气体动压止推轴承性能的影响规律。综合衡量加工难度及数值计算结果中气体动压止推轴承性能表现，加工出刚性表面气体动压止推轴承。同时选用新型弹性箔片材料完成波箔、平箔的压制及热处理工艺，设计开发了箔片动压止推轴承。搭建了单侧气体动压止推轴承实验台，重点对轴承的承载力、起飞转速、摩擦力矩等进行监测与分析。通过实验研究明确了轴承启停过程，同时发现：起飞瞬间刚性表面气体动压止推轴承与弹性表面气体动压止推轴承位移响应方向相反，且在相同轴向载荷条件下，弹性表面气体动压止推轴承起飞转速较同种结构的刚性表面气体动压止推轴承有1/2~2/3的下降。
- 气体动压 /
- 止推轴承 /
- 轴承实验台 /
- 启停过程 /
- 起飞转速
Abstract: To deal with the dynamic characteristics of the air-dynamic lubrication foil thrust bearing, a model of rigid-surface bearing was developed. Through numerical simulation, the effect of structural parameters and speed on performance of rigid surface air-dynamic lubrication thrust bearing were studied. Considering the manufacturing difficulties and the results of numerical simulation, a rigid-surface thrust bearing and a bump kind of aerodynamic compliant foil thrust bearing were developed. And a kind of foil metal was successfully used, the punching process and heat treatment were also accomplished. In order to measure the bearing capacity, lift-off speed, and drag torque in the on-off operation, a single-surface experiment rig was set up. It was found that different dynamic displacement responses occurred between the two kinds of bearings at the beginning of lift-off. Meanwhile, the lift-off speed of flexible surface bearing had a ratio of 1/2-2/3 advantage under the same axial load.
- air-dynamic lubrication /
- thrust bearing /
- bearing experiment rig /
- on-off operation /
- lift-off speed

HTML

参考文献(18)

[1]	LANG O R,STEINHILPER W.滑动轴承［M］.王成焘,曹永上,译.北京：机械工业出版社,1986：95-106.
[2]	BLOK H,VAN ROSSUM J J.The foil bearing a new departure in hydrodynamic lubrication［J］.Lubrication Engineering,1953,9(6):316-320.
[3]	FRANCK B,MIHAI A,ROMAIN G,et al.Experimental analysis of the start-up torque of a mildly loaded foil thrust bearing［J］.Journal of Tribology,2013,135(3):031702.1-031702.7.
[4]	GAD A M,KANEKO S.A new structural stiffness model for bump-type foil bearings:application to generation Ⅱ gas lubricated foil thrust bearing［J］.Journal of Tribology,2014,136(4):216-223.
[5]	RUBIO D,SAN A L.Bump-type foil bearing structural stiffness:experiments and predictions［J］.Journal of Engineering for Gas Turbines and Power,2006,128(3):653-660.
[6]	CHRISTOPHER D C,ROBERT J B.Remaining technical challenges and future plans for oil-free turbomachinery［R］.ASME Paper GT2010-22086,2010.
[7]	DYKAS B,BRUCKNER R,DELLACORTE C,et al.Design,fabrication,and performance of foil gas thrust bearings for microturbomachinery applications［J］.Journal of Engineering for Gas Turbines and Power,2008,131(1):629-639.
[8]	闫佳佳.弹性箔片动压气体止推轴承-转子系统动力学特性［D］.哈尔滨：哈尔滨工业大学,2012.YAN Jiajia.Research on dynamic characteristics of compliant foil gas bearing-rotor system［D］.Harbin:Harbin Institute of Technology,2012.（in Chinese）
[9]	杨利花.可倾瓦与弹性箔片动压气体轴承的性能研究［D］.西安：西安交通大学,2009.YANG Lihua.Study on performance of aerodynamic tilting-pad and compliant foil bearing［D］.Xi’an:Xi’an Jiaotong University,2009.(in Chinese)
[10]	林韶宁,李军,朱朝辉,等.新型弹性箔片动压气体止推轴承的实验研究［J］.西安交通大学学报,2009,39(7):701-705.LIN Shaoning,LI Jun,ZHU Zhaohui,et al.Experimental study of new aerodynamic complaint foil thrust gas bearing［J］.Journal of Xi’an Jiaotong University,2009,39(7):701-705.(in Chinese)
[11]	HESHMAT H.Advancements in the performance of aerodynamic foil journal bearings:high speed and load capability［J］.Journal of Tribology,1994,116（2）:287-294.
[12]	FRANCK B,MIHAI A,ROMAIN G.Experimental analysis of the dynamic characteristics of a foil thrust bearing［J］.Journal of Tribology,2015,137(2):021703.1-021703.8.
[13]	ANDRS L S,RYU K,DIEMER P.Prediction of gas thrust foil bearing performance for oil-free automotive turbochargers［R］.ASME Paper GT2014-25940,2014.
[14]	KEUN R,ZACHARY A.Bump-type foil bearings and flexure pivot tilting pad bearings for oil-free automotive turbochargers:highlights in rotor dynamic performance［J］.Journal of Engineering for Gas Turbines and Power,2015,138(4):042501.1-042501.10.
[15]	徐方程,刘占生,张广辉,等.气体止推箔片轴承试验台设计及实验［J］.航空动力学报,2016,31(9):2298-2304.XU Fangcheng,LIU Zhansheng,ZHANG Guanghui,et al.Test rig design and experiment of gas foil thrust bearing［J］.Journal of Aerospace Power,2016,31(9):2298-2304.(in Chinese)
[16]	闫佳佳,刘占生,张广辉,等.考虑稀薄气体效应的止推箔片轴承静特性分析［J］.航空动力学报,2016,31(6):1521-1529.YAN Jiajia,LIU Zhansheng,ZHANG Guanghui,et al.Static characteristics analysis of foil thrust bearing considering the rare-field gas effect［J］.Journal of Aerospace Power,2016,31(6):1521-1529.(in Chinese)
[17]	冯凯,张俊,王法义.径向间隙及加工工艺对气体箔片轴承性能的影响［J］.航空动力学报,2016,31(11):2773-2780.FENG Kai,ZHANG Jun,WANG Fayi.Influence of radial clearance and processing technology on structural properties of gas foil bearing［J］.Journal of Aerospace Power,2016,31(11):2773-2780.(in Chinese)
[18]	DONGHYUN L,DAEJONG K.Design and performance prediction of hybrid air foil thrust bearings［J］.Journal of Engineering for Gas Turbines and Power,2011,133(4):042501.1-042501.13.