通道截面形状对碳氢燃料流量分配的影响

张晓红; 姜俞光; 秦江; 鲍文

doi:10.13224/j.cnki.jasp.2019.09.015

通道截面形状对碳氢燃料流量分配的影响

doi: 10.13224/j.cnki.jasp.2019.09.015

1.
西北工业大学动力与能源学院,西安 710072
2.
哈尔滨工业大学能源科学与工程学院,哈尔滨 150001

基金项目: 国家自然科学基金(51606051)

计量
- 文章访问数: 699
- HTML浏览量: 73
- PDF量: 496
- 被引次数: 0
出版历程
- 收稿日期: 2019-03-15
- 刊出日期: 2019-09-28

Effect of channel cross sectional shape on flow distribution of hydrocarbon fuel

摘要

摘要: 关注超燃冲压发动机冷却通道截面形状对碳氢燃料流量分配的影响,以平行四边形通道为例和矩形通道进行对比,对并联通道中碳氢燃料流动换热过程进行了三维数值建模。结果表明：不同高宽比下,平行四边形通道相比矩形通道具有更大流固间换热面积,因而在流量分配和冷却效果方面都优于矩形通道,加热面壁温峰值降幅最大可达226 K。通道倾角对流量分配也有重要影响,大通道倾角能实现更合理的流量分配和冷却效果;倾角从105°增加到150°时,加热面壁温峰值降低了287 K。在非理想分汇流布置(以U型分汇流布置为例)和非均匀热流条件下验证了平行四边形通道设计,说明了此设计的实用价值。研究结果对超燃冲压发动机冷却通道设计有一定参考意义。
- 流量分配 /
- 并联通道 /
- 截面形状 /
- 碳氢燃料 /
- 发动机冷却
Abstract: The effect of cooling channel cross sectional shape on the flow distribution of hydrocarbon fuel in SCRamjet was researched. Parallelogram shape cooling channel was taken as an example to compare with rectangular channel. 3-D modelling of the flow and heat transfer of hydrocarbon fuel in multiple cooling channels under supercritical pressure was done. Under different channel aspect ratios, the parallelogram channel was better both in flow distribution and cooling effect because of the larger heat exchange area. The maximum heated wall temperature fell 226 K at most. Then the angle of the parallelogram channel was also important. Larger angle design led to larger heat exchange area and improved the flow distribution and cooling effect. The maximum heated wall temperature fell 287 K when the channel angle increased from 105° to 150°. The effect of practical headers was also taken into consideration. The parallelogram channel design was validated under the joint influence of U-type headers and non-uniform thermal boundary condition, showing good application value. The results of this work offer possible solution to the cooling channel design of SCRamjet.
- flow distribution /
- parallel channels /
- cross sectional shape /
- hydrocarbon fuel /
- engine cooling

HTML

参考文献(34)

[1]	CURRAN E T.SCRamjet engines:the first forty years［J］.Journal of Propulsion and Power,2001,17(6):1138-1148.
[2]	田野,肖保国,张顺平,等.双模态冲压发动机燃烧性能初步研究［J］.航空动力学报,2016,31(12):2921-2927.TIAN Ye,XIAO Baoguo,ZHANG Shuiping,et al.Preliminary study on combustion performance of dual-mode scramjet engine［J］.Journal of Aerospace Power,2016,31(12):2921-2927.(in Chinese)
[3]	ZHANG D,FENG Y,ZHANG S,et al.Quasi-one-dimensional model of SC-ramjet combustor coupled with regenerative cooling［J］.Journal of Propulsion and Power,2016,32(3):687-697.
[4]	蒋劲,张若凌,杨洋,等.超燃冲压发动机典型部件热防护［J］.航空动力学报,2013,28(9):1921-1926.JIANG Jin,ZHANG Ruoling,YANG Yang.Thermal protection of scramjet typical components［J］.Journal of Aerospace Power,2013,28(9):1921-1926.(in Chinese)
[5]	ZHANG D,YANG S,ZHANG S,et al.Thermodynamic analysis on optimum performance of SC-ramjet engine at high Mach numbers［J］.Energy,2015,90:1046-1054.
[6]	TADDEO L,GASCOIN N,FEDIOUN I,et al.Dimensioning of automated regenerative cooling:setting of high-end experiment［J］.Aerospace Science and Technology,2015,43:350-359.
[7]	TADDEO L,GASCOIN N,CHETEHOUNA K,et al.Experimental study of pyrolysis-combustion coupling in a regeneratively cooled combustor:system dynamics analysis［J］.Aerospace Science and Technology,2017,67:473-483.
[8]	QIN J,JIANG Y,FENG Y,et al.Flow rate distribution of cracked hydrocarbon fuel in parallel pipes［J］.Fuel,2015,161:105-112.
[9]	CHEN Y,WANG Y,BAO Z,et al.Numerical investigation of flow distribution and heat transfer of hydrocarbon fuel in regenerative cooling panel［J］.Applied Thermal Engineering,2016,98:628-635.
[10]	PARRIS D K,LANDRUM D B.Effect of tube geometry on regenerative cooling performance［R］.AIAA-2005-4301,2005.
[11]	WENNERBERG J,JUNG H,SCHUFF R,et al.Study of simulated fuel flows in high aspect ratio cooling channels［R］.AIAA-2006-4708,2006.
[12]	JUNG H,MERKLE C,SCHUFF R,et al.Detailed flowfield predictions of heat transfer to supercritical fluids in high aspect ratio cooling channels［R］.AIAA-2007-5548,2007.
[13]	KNAB O,FRHLICH A,WENNERBERG D,et al.Advanced cooling circuit layout for the vinci expander cycle thrust chamber［R］.AIAA-2002-4005,2002.
[14]	PIZZARELLI M,NASUTI F,ONOFRI M.CFD analysis of transcritical methane in rocket engine cooling channels［J］.Journal of Supercritical Fluids,2012,62(1):79-87.
[15]	PIZZARELLI M,NASUTI F,PACIORRI R,et al.Numerical analysis of three-dimensional flow of supercritical fluid in asymmetrically heated channels［J］.AIAA Journal,2009,47(11):2534-2543.
[16]	WANG L,CHEN Z,MENG H.Numerical study of conjugate heat transfer of cryogenic methane in rectangular engine cooling channels at supercritical pressures［J］.Applied Thermal Engineering,2013,54(1):237-246.
[17]	PIZZARELLI M,NASUTI F,ONOFRI M.Effect of cooling channel aspect ratio on rocket thermal behavior［J］.Journal of Thermophysics and Heat Transfer,2014,28(3):410-417.
[18]	康玉东,孙冰,高翔宇.液体火箭发动机推力室冷却通道温度分层数值研究［J］.航空动力学报,2009,24(8):1904-1910.KANG Yudong,SUN Bing,GAO Xiangyu.Numerical investigations of thermal stratification in cooling channel of liquid rocket engine thrust chamber［J］.Journal of Aerospace Power,2009,24(8):1904-1910.(in Chinese)
[19]	PIZZARELLI M,NASUTI F,ONOFRI M.Trade-off analysis of high-aspect-ratio-cooling-channels for rocket engines［J］.International Journal of Heat and Fluid Flow,2013,44:458-467.
[20]	ZHANG S,CUI N,XIONG Y,et al.Effect of channel aspect ratio on chemical recuperation process in advanced aeroengines［J］.Energy,2017,123(1):9-19.
[21]	JIANG Y,XU Y,ZHANG S,et al.Parametric study on the distribution of flow rate and heat sink utilization in cooling channels of advanced aero-engines［J］.Energy,2017,138:1056-1068.
[22]	ZHANG S,FENG Y,JIANG Y,et al.Thermal behavior in the cracking reaction zone of scramjet cooling channels at different channel aspect ratios［J］.Acta Astronautica,2016,127(1):41-56.
[23]	ZHANG S,QIN J,XIE K,et al.Thermal behavior inside scramjet cooling channels at different channel aspect ratios［J］.Journal of Propulsion and Power,2015,30(1):57-70.
[24]	ZHANG S,FENG Y,ZHANG D,et al.Parametric numerical analysis of regenerative cooling in hydrogen fueled scramjet engines［J］.International Journal of Hydrogen Energy,2016,41(25):10942-10960.
[25]	KIM S M,MUDAWAR I.Analytical heat diffusion models for different micro-channel heat sink cross section geometries［J］.International Journal of Heat and Mass Transfer,2010,53(19):4002-4016.
[26]	LEE S M,KIM K Y.Comparative study on performance of a zigzag printed circuit heat exchanger with various channel shapes and configurations［J］.Heat and Mass Transfer,2013,49(7):1021-1028.
[27]	KIM D K,JUNG J,KIM S J.Thermal optimization of plate-fin heat sinks with variable fin thickness［J］.International Journal of Heat and Mass Transfer,2010,53(25):5988-5995.
[28]	YANG Q,CHETEHOUNA K,GASCOIN N,et al.Experimental study on combustion modes and thrust performance of a staged-combustor of the SCRamjet with dual-strut［J］.Acta Astronautica,2016,122(1):28-34.
[29]	WANG J Y.Pressure drop and flow distribution in parallel-channel configurations of fuel cells:U-type arrangement［J］.International Journal of Hydrogen Energy,2008,33(21):6339-6350.
[30]	China Aeronautical Materials Handbook Editorial Committee.China Aeronautical Materials Handbook［M］.Beijing:China Standard Press,2002.
[31]	ZHU Y,LIU B,JIANG P.Experimental and numerical investigations on n-decane thermal cracking at supercritical pressures in a vertical tube［J］.Energy & Fuels,2013,28(1):466-474.
[32]	ZHANG C,YAO Z,QIN J,et al.Experimental study on measurement and calculation of heat flux in supersonic combustor of scramjet［J］.Journal of Thermal Science,2015,24(3):254-259.
[33]	LIAO S M,ZHAO T S.Measurements of heat transfer coefficients from supercritical carbon dioxide flowing in horizontal mini/micro channels［J］.Transactions-American Society of Mechanical Engineers Journal of Heat Transfer,2002,124(3):413-420.
[34]	JIANG Y,FENG Y,ZHANG S,et al.Numerical heat transfer analysis of transcritical hydrocarbon fuel flow in a tube partially filled with porous media［J］.Open Physics,2016,14(1):659-667.