基于流体网络法的喷管冷却气流量分配计算方法

杨韫加; 陈海昕; 许羚

doi:10.13224/j.cnki.jasp.20210027

基于流体网络法的喷管冷却气流量分配计算方法

doi: 10.13224/j.cnki.jasp.20210027

1.
清华大学航天航空学院，北京 100084
2.
中国航空发动机集团有限公司沈阳发动机研究所，沈阳 110015

基金项目: 国家重大项目（GJXM92579）

详细信息

作者简介:
杨韫加（1998-），男，博士生，研究领域为喷管空气动力学。

中图分类号: V233.5
计量
- 文章访问数: 122
- HTML浏览量: 22
- PDF量: 39
- 被引次数: 0
出版历程
- 收稿日期: 2021-01-18
- 刊出日期: 2022-06-28

Calculation method of cooling air distribution in nozzle based on fluid network analysis method

1.
School of Aerospace Engineering，Tsinghua University，Beijing 100084，China
2.
Shenyang Engine Research Institute，Aero Engine Corporation of China，Shenyang 110015，China

摘要

摘要: 流体网络法对喷管气膜冷却问题具有独特的优势，但难以反映出入流对冷却气流道静压变化的影响。针对此引入了可反映出入流导致静压变化的管道元件，并基于孔口速度落后角对静压变化量进行了建模。验证算例表明，这一改进使沿程静压变化趋势与实际吻合较好，使冷却气流量分配计算误差降低到0.5%以下。将改进后的流体网络法与主流通道的计算流体力学模拟耦合用于分析喷管冷却气流量分配，与全计算流体力学模拟相比结果差异小于1.2%，且大幅降低计算量；在某型喷管设计中的应用表明，可以有效反映冷却结构改变对冷却气流量分配的影响。
- 流体网络法 /
- 喷管冷却 /
- 冷却气流量分配 /
- 耦合计算 /
- 气膜孔
Abstract: The fluid network analysis method has its unique advantages in nozzle film cooling problems，but it cannot predict the influence of inlet/outlet flow on the static pressure change along cooling air channel.In order to solve this problem，a type of element that can describe the static pressure change caused by inlet/outlet flow was introduced，and the variation of static pressure was quantified based on the lag angle of velocity at hole entrance.Results on verification examples showed that the improved method can correctly capture the static pressure trend along the cooling air channel and reduced the calculation error of cooling air distribution to less than 0.5%.The improved fluid network analysis method was coupled with computational fluid dynamics simulation of mainstream，and used to analyze cooling air distribution in nozzle.Compared with computational fluid dynamics simulation for whole system，the method had very low computation cost，meanwhile the difference between two methods was less than 1.2%.The application in the design of a nozzle showed that the method reflected the influence of cooling structure changes on cooling air distribution effectively.
- fluid network analysis method /
- nozzle cooling /
- cooling air distribution /
- coupled calculation /
- film hole

HTML

参考文献(24)

[1]	卢浩浩，吉洪湖，王丁，等.部件冷却对二元俯仰矢量排气系统红外特征抑制实验[J].航空动力学报,2017，32（9）:2070-2079.
[2]	额日其太,王志杰,吴寿生.高速热喷流条件下二元收扩喷管扩张段壁面冷却的初步试验研究[J].航空动力学报,2002,17（1）:40-44.
[3]	饶宇,刘宇阳,万超一.具有气膜出流孔和针肋的双层壁冷却结构内的冲击传热性能[J].航空学报,2018,39（1）:99-107.
[4]	EL-JUMMAH A M,ANDREWS G E,STAGGS J E.Impingement/effusion cooling wall heat transfer:conjugate heat transfer computational fluid dynamic predictions[R].Seoul,Korea:ASME Turbo Expo 2016:Turbomachinery Technical Conference and Exposition,2016.
[5]	杨成凤,张靖周,杨卫华.全覆盖气膜孔阵列方式对冷却特性的影响[J].航空动力学报,2010,25（7）:1524-1529.
[6]	KREWINKEL R.A review of gas turbine effusion cooling studies[J].International Journal of Heat and Mass Transfer,2013,66:706-722.
[7]	MENDEZ S,NICOUD F,POINSOT T.Large-eddy simulation of a turbulent flow around a multi-perforated plate[M]∥Kassinos S,Langer C,Iaccarino G,et al.Complex effects in large eddy simulations.Berlin,Germany:Springer,2007.
[8]	MENDEZ S,NICOUD F.Large-eddy simulation of a bi-periodic turbulent flow with effusion[J].Journal of Fluid Mechanics,2008,598:27-65.
[9]	MEITNER P L.Computer code for predicting coolant flow and heat transfer in turbomachinery[M].Cleveland,US:Diane Publishing,1990.
[10]	KUTZ K J,SPEER T M.Simulation of the secondary air system of aero engines[J].Journal of Turbomachinery,1994,116（2）:306-315.
[11]	MAJUMDAR A K,LECLAIR A,MOORE R,et al.Generalized fluid system simulation program （GFSSP）:version 6[R].Orlando,US:51st AIAA/SAE/ASEE Joint Propulsion Conference,2015.
[12]	BONINI A,ANDREINI A,CARCASCI C,et al.Conjugate heat transfer calculations on GT rotor blade for industrial applications:Part Ⅰ equivalent internal fluid network setup and procedure description[C]∥Proceedings of ASME Turbo Expo 2012:Turbomachinery Technical Conference and Exposition Digital Collection.Copenhagen,Denmark:ASME,2012:669-679.
[13]	陶智,侯升平,韩树军,等.流体网络法在发动机空气冷却系统设计中的应用[J].航空动力学报,2009,24（1）:1-6.
[14]	CHI Z,WANG S,REN J,et al.Multi-dimensional platform for cooling design of air-cooled turbine blades[C]∥Proceedings of ASME Turbo Expo 2012:Turbomachinery Technical Conference and Exposition Digital Collection.Copenhagen,Denmark:ASME,2012:207-218.
[15]	刘维.管道网络法在涡轮叶片传热设计中的应用研究[D].哈尔滨:哈尔滨工业大学,2014.
[16]	刘维,温风波,罗磊,等.考虑涡轮传热性能的气动设计耦合计算方法研究[J].推进技术,2018,39（11）:2463-2471.
[17]	史亮,孙彦博,韩万金,等.管网方法在双层壁冷却结构设计中的应用[J].哈尔滨工业大学学报,2017,49（7）:78-85.
[18]	田勇,季路成,邵卫卫,等.冷却涡轮定常/非定常流场的内外耦合快速计算方法[J].航空动力学报,2015,30（10）:2462-2471.
[19]	LI C,LIU J J.A one-dimensional analytical method for turbine blade preliminary cooling design[R].Seoul,Korea:ASME Turbo Expo 2016:Turbomachinery Technical Conference and Exposition,2016.
[20]	CHOWDHURY N H K,ZIRAKZADEH H,HAN J C.A predictive model for preliminary gas turbine blade cooling analysis[J].Journal of Turbomachinery,2017,139（9）:091010.1-091010.12.
[21]	陶文铨.传热学[M].4版.北京:高等教育出版社,2006:216-217.
[22]	曹玉璋.航空发动机传热学[M].北京:北京航空航天大学出版社,2005:162-163.
[23]	FLORSCHUETZ L W ,ISODA Y.Flow distributions and discharge coefficient effects for jet array impingement with initial crossflow[J].Journal of Engineering for Gas Turbines and Power,1983,105（2）:296-304.
[24]	陈四杰.收扩喷管扩张段气膜冷却特性研究[D].南京:南京航空航天大学,2014.