基于椭圆积分的单支点半柔壁喷管大挠度成型半解析求解与验证

尉成果; 张志利; 赖欢; 陈万华; 陈振华; 聂旭涛

doi:10.13224/j.cnki.jasp.20210081

基于椭圆积分的单支点半柔壁喷管大挠度成型半解析求解与验证

doi: 10.13224/j.cnki.jasp.20210081

1.
火箭军工程大学导弹工程学院，西安 710025
2.
中国空气动力研究与发展中心设备设计与测试技术研究所，四川绵阳621000

基金项目: 国家自然科学基金（51935006）

详细信息

作者简介:
尉成果（1987-），男，副研究员，博士生，主要从事风洞结构设计研究。

通讯作者:
聂旭涛（1979-），男，副研究员，博士，主要从事风洞结构设计研究。E-mail：nie_xu_tao@163.com

中图分类号: V216.8
计量
- 文章访问数: 275
- HTML浏览量: 124
- PDF量: 56
- 被引次数: 0
出版历程
- 收稿日期: 2021-02-23
- 刊出日期: 2022-02-28

Semi-analytic solution and verification for large deflection forming of single-jack semi-flexible nozzle based on elliptic integral

1.
College of Missile Engineering， Rocket Force University of Engineering，Xi'an 710025，China
2.
Facility Design and Instrumentation Institute， China Aerodynamics Research and Development Center，Mianyang Sichuan 621000，China

摘要

摘要: 为提升跨超声速风洞单支点半柔壁（SJSF）喷管分析精度和效率，发展了基于椭圆积分的柔性壁板大挠度变形半解析求解方法。以0.3 m低温风洞单支点半柔壁喷管为研究对象，建立型面组件力学模型，基于欧拉梁理论推导柔性壁板型面曲线的微分方程，给出了椭圆积分的表达形式。利用Maple软件编制了计算程序，并以此针对马赫数为1.15和1.3两种工况，开展柔性壁板大挠度变形的半解析求解，得到了变形型面坐标和结构等效应力曲线。通过对比有限元（FEM）仿真结果以及实验测量数据，结果表明：基于椭圆积分的求解结果与其他两种结果均能良好吻合，型面坐标最大偏差分别为喷管出口高度尺寸的0.18‰和0.32‰，结构等效应力最大相对误差小于10%，椭圆积分求解耗时仅为有限元仿真的11.2%。
- 半柔壁喷管 /
- 单支点 /
- 大挠度 /
- 欧拉梁 /
- 椭圆积分
Abstract: To improve the analysis accuracy and efficiency of single-jack semi-flexible（SJSF） nozzles in transonic and supersonic wind tunnels，a semi-analytical solution method based on ellipse integral for the flexible plate large deflection was developed.Taking the 0.3 m cryogenic wind tunnel SJSF nozzle as the research object，the mechanical model was established.Based on the Euler beam theory，the differential formulas of the flexible plate deflection were derived，and the elliptic integral form was obtained.Based on the program compiled using Maple software，the semi-analytic solution was carried out under Mach number of 1.15 and 1.3 conditions.The deformation contour and structural equivalent stress were obtained.Compared with the finite element method （FEM） results and experimental measurement，it showed that the elliptic integral results were in good agreement with the other two results.The maximum error of the contour coordinates was 0.18‰ and 0.32‰ of the nozzle outlet height size，respectively.The maximum relative error of the equivalent stress was less than 10%，and the elliptic integral solution time was only 11.2% of the FEM.
- semi-flexible nozzle /
- single-jack /
- large deflection /
- Euler beam /
- elliptic integral

HTML

参考文献(23)

[1]	廖达雄,陈吉明,郑娟,等.0.6 m连续式跨声速风洞总体性能[J].实验流体力学,2018,32（6）:88-93.
[2]	吴盛豪,房詠柳,陈吉明,等.超声速喷管性能优化研究与应用[J].航空动力学报，2017,32（9）:2139-2144.
[3]	郭东明,雒建斌,方岱宁，等.大型风洞设计建设中的关键科学问题[J].中国科学基金,2017,31（5）:420-427.
[4]	JUHANY K A，HUSAINI H E.Investigation of a single-jack flexible supersonic nozzle[R].Reno，Nevada,US:the 45th AIAA Aerospace Sciences Meeting and Exhibit，2007.
[5]	ROSEN J.The design and calibration of a variable Mach number nozzle[J].Journal of the Aeronautical Sciences,1955,22（7）:484-490.
[6]	赖欢,陈万华,孙德文,等.0.3 m低温连续式跨声速风洞结构设计[J].实验流体力学,2020,34（5）:89-96.
[7]	张伟,高荣,张双喜,等.0.3 m低温风洞液氮供给系统研制[J].航空动力学报，2020,35（5）:1009-1017.
[8]	陈振华,张伟,高荣,等.液氮抽真空制冷的理论及试验[J].航空动力学报,2019,34（9）:1971-1976.
[9]	聂旭涛,郭隆德,刘伯林.基于ADAMS风洞柔壁喷管动力学仿真分析[J].实验流体力学,2011,25（2）:73-76.
[10]	聂旭涛,赖欢,张艳辉.半柔壁喷管机构动力学仿真技术研究[J].实验流体力学,2012,26（4）:91-95.
[11]	CHEN Pengfei，WU Feng，XU Jinglei，et al.Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle[J].Chinese Journal of Aeronautics，2016,29（6）:1477-1483.
[12]	刘佳鑫,秦伟,周扬,等.半柔壁喷管喉块柔板接触力仿真分析[J].机械科学与技术,2020,39（1）:22-27.
[13]	刘铭甲.半挠性喷管挠性板弹性曲线计算方法[J].国防科技大学学报,1992,14（2）:109-114.
[14]	张晓伟,杨嘉陵.柔壁风洞设计中的Elastica反问题[J].航空学报,2005，26（6）:42-46.
[15]	BISSHOPP K E，DRUCKER D C.Large deflection of cantilever beams[J].Quarterly of Applied Mathematics，1945，3（3）:272-275.
[16]	HOWELL L L，LEONARD J N.Optimal loading conditions for non-linear deflections[J].International Journal of Nonlinear Mechanics,1997，32（3）:505-514.
[17]	ZHANG Aimei，CHEN Guimin.A comprehensive elliptic integral solution to the large deflection problems of thin beams in compliant mechanisms[J].Journal of Mechanisms and Robotics,2013,5（2）:80-85.
[18]	张爱梅,陈贵敏,贾建援.基于完备椭圆积分解的交叉簧片式柔性铰链大挠度建模[J].机械工程学报，2014,50（11）:80-85.
[19]	安朝,谢长川,杨超.弹性欧拉梁大变形分析的椭圆积分统一形式[EB/OL].[2021-01-27].https:∥doi.org/10.13700/j.bh.1001-5965.2020.0186.
[20]	XU Ke，LIU Haitao，XIAO Juliang.Static deflection modeling of combined flexible beams using elliptic integral solution[J].International Journal of Non-Linear Mechanics,2020,129:103637.1-103637.8.
[21]	XU Ke，LIU Haitao，YUE Wei，et al.Kinematic modeling and optimal design of a partially compliant four-bar linkage using elliptic integral solution[J].Mechanism and Machine Theory,2020，157:104214.1-104214.15.
[22]	ALESSANDRO C，MICHELE L，GAETANO S.Alternative elliptic integral solution to the beam deflection equations for the design of compliant mechanisms[J].International Journal on Interactive Design and Manufacturing（IJIDeM）,2019,13（2）:1-7.
[23]	刘鸿文.材料力学[M].北京：高等教育出版社，2004.