节流水平对气液针栓喷注单元雾化特性的影响

张波涛; 李平; 杨岸龙; 杨宝娥

doi:10.13224/j.cnki.jasp.20210235

节流水平对气液针栓喷注单元雾化特性的影响

doi: 10.13224/j.cnki.jasp.20210235

1.
中国航天科技集团有限公司西安航天动力研究所液体火箭发动机技术重点实验室，西安 710100
2.
中国航天科技集团有限公司航天推进技术研究院，西安 710100

基金项目: 国家重点基础研究发展计划（613193）；国家自然科学基金（11502186）

详细信息

作者简介:
张波涛（1990-），男，博士生，主要从事液体火箭发动机喷雾燃烧技术研究。

中图分类号: V434.3
计量
- 文章访问数: 55
- HTML浏览量: 0
- PDF量: 117
- 被引次数: 0
出版历程
- 收稿日期: 2021-05-12
- 刊出日期: 2022-04-28

Effects of throttling level on spray characteristics of gas-liquid pintle injector unit

1.
National Key Laboratory of Science and Technology on Liquid Rocket Engines， Xi'an Aerospace Propulsion Institute， China Aerospace Science and Technology Corporation，Xi'an 710100，China
2.
Academy of Aerospace Propulsion Technology， China Aerospace Science and Technology Corporation，Xi'an 710100，China

摘要

摘要: 为了分析气液针栓喷注单元雾化特性和雾化机制，采用背光成像技术和相位多普勒（PDA）系统进行试验研究，获得了雾化模式、体积流量分布、索泰尔平均直径（SMD）分布和速度场随节流水平的变化规律。结果表明：气液针栓喷注单元雾场形态为扇形雾场，雾化模式为剪切破碎。体积流量沿径向呈单峰形分布，随着节流水平降低，雾场外缘向中心收缩。SMD沿径向呈现递增规律，雾化最好的区域分布在雾场中心和两侧。SMD随节流水平增加而增大。当动量比不变时，节流水平对SMD的分布范围影响很小。针栓头部下方的中心回流区轴向尺寸随着节流水平降低而减小。
- 变推力液体火箭发动机 /
- 气液针栓喷注单元 /
- 节流水平 /
- 雾化特性 /
- 雾化模式 /
- 索泰尔平均直径 /
- 速度场
Abstract: In order to analyze the spray characteristics and spray mechanism of gas-liquid pintle injector unit，the effects of throttling level on spray pattern，volume flow rate distribution，Sauter mean diameter （SMD） distribution and the velocity field were obtained by using backing-lighting photography technique and phase Doppler anemometry （PDA） system for the spray characteristics of gas-liquid pintle injector unit.The results showed that the spray of gas-liquid pintle injector was a fan-shaped form and the spray pattern was presented by shearing breaking.The volume flow rate presented a single peak distribution along the radial direction.With the decrease of throttling level，the edge of spray field shrank to the center.The SMD increased along the radial direction，and the best spay area was distributed in the center and both sides of the spay field.The value of SMD increased with the increasing throttling level.When the momentum ratio was constant，the throttling level had little influence on the variation range of SMD.The axial length of the backflow area below the pintle head decreased with the decreasing throttling level.
- throttling liquid rocket engine /
- gas-liquid pintle injector unit /
- throttling level /
- spray characteristics /
- spray pattern /
- Sauter mean diameter /
- velocity field

HTML

参考文献(23)

[1]	DRELLSER G A,BAUER J M.TRW pintle engine heritage and performance characteristics[R].AIAA 2000-3871,2000.
[2]	刘昌波,兰晓辉,李福云,等.载人登月舱下降发动机技术研究[J].火箭推进,2011,37（2）:8-13.
[3]	雷娟萍,兰晓辉,章荣军,等.嫦娥三号探测器7 500 N变推力发动机研制[J].中国科学（技术科学）,2014,44（6）:569-575.
[4]	王丹,陈宏玉,周晨初.电动泵压式发动机系统方案与性能评估[J].火箭推进,2018,44（2）:28-32.
[5]	沈文金,叶小强.深度变推发动机浮动环工作适应性研究[J].火箭推进,2017,43（5）:28-33.
[6]	王凯，雷凡培，张波涛，等．针栓式喷注单元雾化角模型分析研究[J].航空学报,2020,41（10）:123622.1-123622.15.
[7]	BLAKELY J,FREEBERG J,HOGEE J.Spray cone formulation from pintle-type injecotr systems in liquid rocket engines[R].AIAA 2019-0152,2019.
[8]	BOETTCHER P A,DAMAZO J S,SHEPHERD J E,et al.Visualization of tranverse annular jets[R].Minneapolis,US:the 62nd Annual Meeting of the APS Division of Fluid Dynamic,2009.
[9]	SON M,YU K,KOO J,et al.Effect of momentum ration and weber number on spray half angles of liquid controlled pintle injector[J].Journal of Thermal Science,2015,24（1）:37-43.
[10]	张波涛,李平,王凯,等.针栓喷注器中心推进剂偏转角模型分析研究[J].推进技术,2021,42（7）:1534-1543.
[11]	张波涛,李平,杨宝娥.气液针栓喷注器在节流水平下的雾化角模型分析[J].宇航学报,2021,42（2）:249-258.
[12]	王凯,雷凡培,杨岸龙,等.针栓式喷注单元膜束撞击雾化混合过程数值模拟[J].航空学报,2020,41（9）:123802.1-123802.15.
[13]	FANG X X,SHEN C B.Study on atomization and com-bustion characteristics of LOx/methane pintle injectors[J].Acta Astronautica,2017,136:369-379.
[14]	王凯,雷凡培,杨岸龙,等.针栓式喷注器液膜下漏率预估模型[J].航空动力学报,2020,35（10）:2223-2234.
[15]	成鹏.变推力火箭发动机喷雾燃烧动态过程研究[D].长沙:国防科技大学,2018.
[16]	陈慧源,李清廉,成鹏,等.动量比及其调节方式对针栓喷注器喷雾特性的影响[J].物理学报,2019,68（20）:204704.1-204704.14.
[17]	张紫豪.可调针栓喷注器喷雾特性试验研究[D].长沙:国防科技大学,2018.
[18]	方昕昕,沈赤兵,张新桥.针栓式喷注器锥形液膜破碎特性试验[J].航空动力学报,2016,31（12）:3004-3009.
[19]	方昕昕,沈赤兵,成鹏,等.针栓式喷注器雾化特性试验[J].航空动力学报,2017,32 （8）:1854-1860.
[20]	SON M,YU K,RADHAKRISHNAN K,et al.Verification on spray simulation of a pintle injector for liquid rocket engine[J].Journal of Thermal Science,2016,25（1）:90-96.
[21]	石璞,朱国强,李进贤,等.液体火箭发动机针栓喷注器雾化燃烧技术研究进展[J].火箭推进,2020,46（4）:1-13.
[22]	张波涛,李平,王凯,等.变推力液体火箭发动机中针栓喷注器研究综述[J].宇航学报,2020,41（12）:1481-1489.
[23]	沈熊.激光多普勒测速技术及应用[M].北京:清华大学出版社,2004.