Investigation on influence mechanism of aspect ratio on thermal-solid interaction response of serpentine nozzle
-
摘要:
为了明晰第一弯出口宽度比对S弯喷管流动传热和结构响应的影响，采用串行双向松耦合方法，研究了不同第一弯出口宽度比下的热固耦合响应影响。结果表明：多弯且不同沿程截面过度的结构特征，使得喷管内部流动传热复杂化，S弯喷管整体热流密度分布不均匀，以第一弯处上壁面传热最强；随着第一弯出口宽度比的增加，第一弯处上壁面热流密度不断增加；喷管出口等直段旋涡结构使得传热受阻，热流密度较低；温度响应中，各个喷管第一弯处上壁面产生局部极大值，随后转移至进口，第一弯出口宽度比0.715的喷管，在下壁面进口位置附近产生局部极小值，不同于其余喷管；各个S弯喷管应力随时间的增加，先增加后减小，随着第一弯出宽度比的增加，各喷管应力最大值，出现时刻推迟且在不断减小；第一弯出口宽度比0.715的喷管首先出现应力最大值，为159.346 MPa，相比于第一弯出口宽度比1.165的构型喷管，提前了10.3 s，减小了27.2%。
Abstract:In order to clarify the effect of the first bend width ratio on the flow heat transfer and structural response of the serpentine nozzle, the effects of the thermal-solid coupling responses under different first bend width ratios were investigated by using the two-way loose coupling method. The results showed that the structural characteristics of multiple bends and different cross sections along the path complicated the heat transfer inside the nozzle, the overall heat flux distribution of the serpentine nozzle was non-uniform, and the heat transfer was strongest on the upper wall at the first bend; with the increase of the width ratio of the first bend, the heat flux of the upper wall at the first bend increased; the vortex structures of the straight section of the nozzle exit made the heat transfer blocked and the heat flux lower; in the temperature response, all nozzles produced extreme values of temperature on the upper wall at the first bend, which were subsequently shifted to the inlet, and the nozzle with a width ratio of 0.715 of the first bend produced extreme values of temperature near the position of the inlet on the lower wall, unlike the rest of the nozzles; the stresses of all serpentine nozzles increased and then decreased with time. As the width ratio of the first bend increased, the moment of maximum stress in each nozzle was delayed and the maximum stress decreased; the nozzle with a width ratio of 0.715 at the first bend was the first to show a stress maximum of 159.346 MPa, which was 10.3 s earlier and 27.2% less compared with the nozzle of a configuration with a width ratio of 1.165 at the first bend.
-
图 5 圆管外壁面热流密度分布
Figure 5. Heatflux distribution on the outer wall surface of the circular tube
图 6 末时刻圆管外壁面温度分布
Figure 6. Temperature distribution of the outer wall surface of the circular tube at the last moment
图 13 流通截面沿着轴向分布示意图
Figure 13. Schematic distribution of cross sections along the axial direction
图 15 不同第一弯出口宽度比S弯喷管几何模型
Figure 15. Geometric model of the serpentine nozzle with different aspect ratios
图 16 不同第一弯出口宽度比下对称面Ma分布
Figure 16. Comparisons of Mach number at the symmetric surface under different aspect ratio
图 17 不同第一弯出口宽度比下内壁面上、下对称面静压分布
Figure 17. Comparisons of static pressure distributions at the upper and lower symmetric surface of the inner wall surface under different aspect ratios
图 18 不同第一弯出口宽度比下内壁面上、下对称面热流密度分布
Figure 18. Comparisons of heatflux distributions at the upper and lower symmetric surface of the inner wall surface under different aspect ratios
图 20 不同第一弯出口宽度比下对称面马赫数及流线分布
Figure 20. Comparisons of Mach number and streamline distributions at the symmetric surface under different aspect ratios
图 21 沿程截面流线分布
Figure 21. Comparisons of streamline distributions of cross sections along the axial direction
图 22 不同第一弯出口宽度比下沿程截面内壁面周向静压分布
Figure 22. Comparisons of static pressure distributions of cross sections along the axial direction under different aspect ratios
图 23 不同第一弯出口宽度比内壁面热流密度分布
Figure 23. Comparisons of heatflux distributions on the inner wall under different aspect ratios
图 24 不同第一弯出口宽度比不同时刻内壁面对称面温度分布
Figure 24. Comparisons of temperature distribution at the symmetric inner wall surface at different times with different aspect ratios
图 25 不同第一弯出口宽度比S弯喷管温度分布（t=300 s）
Figure 25. Comparisons of temperature distribution of serpentine nozzle with different aspect ratios （t=300 s）
图 26 热应力最大值时刻不同第一弯出口宽度比S弯喷管热应力分布
Figure 26. Thermal stress distribution of serpentine nozzle with different aspect ratio at the moment of maximum thermal stress
图 28 不同时刻不同第一弯出口宽度比S弯喷管出口端外壁面热应力分布
Figure 28. Comparisons of thermal stress distribution on the outer wall surface of the exit end of serpentine nozzle with different aspect ratios at different times
表 1 无量纲设计参数值
Table 1. Values of non-dimensional design parameters
无量纲设计参数 数值 L/D 2.43 L1/L2 0.67 We/He 4.00 W1/D 1.11 A1/Ain 0.60 遮挡率 0.25 
下载: 导出CSV
表 2 S弯喷管材料参数
Table 2. Material parameters of serpentine nozzle
T/K k/（W/（m·K）） E/GPa γ 293.15 12.5 210 0.382 373.15 14.0 206 0.389 423.15 14.8 473.15 15.9 200 0.389 523.15 16.7 573.15 17.6 194 0.392 623.15 18.5 673.15 19.2 188 0.405 723.15 19.9 773.15 20.6 181 0.404 823.15 21.3 873.15 22.1 174 0.395 973.15 166 0.415
下载: 导出CSV
表 3 不同第一弯出口宽度比S弯喷管的第二段S弯通道的无量纲纵向偏距
Table 3. Values of longitudinal offset distance of the second channel of the serpentine nozzle under different aspect ratios
W1/D ΔY2/L2 0.715 0.182 0.865 0.161 1.015 0.147 1.165 0.135
下载: 导出CSV
-
[1] 赵鸿燕,倪永平,王秀萍. 红外探测器的发展及其在空空导弹上的应用[J]. 飞航导弹,2008(7): 46-49. ZHAO Hongyan,NI Yongping,WANG Xiuping. Development of infrared detector and its application in air-to-air missile[J]. Winged Missiles Journal,2008(7): 46-49. (in ChineseZHAO Hongyan, NI Yongping, WANG Xiuping. Development of infrared detector and its application in air-to-air missile[J]. Winged Missiles Journal, 2008(7): 46-49. (in Chinese) [2] BARANWAL N,MAHULIKAR S P. Infrared signature of aircraft engine with choked converging nozzle[J]. Journal of Thermophysics and Heat Transfer,2016,30(4): 854-862. doi: 10.2514/1.T4641 [3] JOHANSSON M. FOT25 2003-2005 propulsion integration: final report: FOI-R-2017-SE[R]. Stockholm,Sweden: Swedish Defence Research Agency,2006. [4] LINDERMEIR E,RUETTEN M. IR-signature of the MULDICON configuration determined by the IR-signature model MIRA: AIAA2018-3166 [R]. Reston,US: AIAA,2018. [5] SUN X L,WANG Z X,ZHOU L,et al. Experimental and computational investigation of double serpentine nozzle[J]. Proceedings of the Institution of Mechanical Engineers: Part G Journal of Aerospace Engineering,2015,229(11): 2035-2050. doi: 10.1177/0954410014564402 [6] SMITH J,DALENBRING M. Aeroelastic simulation of S-duct dynamics using structure-coupled CFD: FOI SE-164 90 [R]. Stockholm,Sweden: Swedish Defence Research Agency,2006. [7] 孙鹏,周莉,王占学,等. 双S弯喷管的流固耦合特性研究[J]. 推进技术,2022,43(10): 210349. SUN Peng,ZHOU Li,WANG Zhanxue,et al. Fluid-structure interaction characteristic of double serpentine nozzle[J]. Journal of Propulsion Technology,2022,43(10): 210349. (in ChineseSUN Peng, ZHOU Li, WANG Zhanxue, et al. Fluid-structure interaction characteristic of double serpentine nozzle[J]. Journal of Propulsion Technology, 2022, 43(10): 210349. (in Chinese) [8] 李秋琳,周莉,孙鹏,等. 出口宽高比对S弯喷管流固耦合特性影响[J]. 航空学报,2023,44(14): 628204. LI Qiulin,ZHOU Li,SUN Peng,et al. Influence mechanism of aspect ratio on fluid-structure interaction characteristics of serpentine nozzle[J]. Acta Aeronautica et Astronautica Sinica,2023,44(14): 628204. (in ChineseLI Qiulin, ZHOU Li, SUN Peng, et al. Influence mechanism of aspect ratio on fluid-structure interaction characteristics of serpentine nozzle[J]. Acta Aeronautica et Astronautica Sinica, 2023, 44(14): 628204. (in Chinese) [9] VOGEL R,GRANDHI R. Structural acoustic analysis and design of aircraft components: AIAA 2012-5557 [R]. Reston,US: AIAA,2012. [10] CROWE D S,MARTIN C L. Effect of geometry on exit temperature from serpentine exhaust nozzles: AIAA2015-1670 [R]. Reston,US: AIAA,2015. [11] CROWE D S,MARTIN C L. Hot streak characterization in serpentine exhaust nozzles: AIAA2016-4502 [R]. Reston,US: AIAA,2016. [12] HUI Z H,SHI J W,ZHOU L,et al. The influence of the adverse pressure gradient on the flow characteristics of a serpentine nozzle with film cooling[J]. Aerospace Science and Technology,2023,136: 108256. doi: 10.1016/j.ast.2023.108256 [13] HUI Z H,SHI J W,ZHOU L,et al. Effect of inclination angle on the film cooling in a serpentine nozzle with strong adverse pressure gradient[J]. Physics of Fluids,2023,35(4): 046114. doi: 10.1063/5.0147749 [14] FENRICH R W,ALONSO J J. Reliable multidisciplinary design of a supersonic nozzle using multifidelity surrogates: AIAA2017-3826 [R]. Reston,US: AIAA,2017. [15] DEATON J,GRANDHI R. Thermal-structural analysis of engine exhaust-washed structures: AIAA 2010-9236[R]. Reston,US: AIAA,2010. [16] DEATON J D,GRANDHI R V. Significance of geometric nonlinearity in the design of thermally loaded structures: AIAA 2015-1431[R] Reston,US: AIAA,2015. [17] NIGAM N,AYYALASOMAYAJULA S K,TANG Y Y,et al. Design optimization of advanced exhaust systems: AIAA 2017-3331 [R]. Reston,US: AIAA,2017. [18] URBANCZYK P S,ALONSO J J,NIGAM N,et al. Coupled multiphysics analysis for design of advanced exhaust systems: AIAA2017-0799 [R] Reston,US: AIAA,2017. [19] 程经理,黄盛,周莉,等. 出口宽高比对S弯喷管热固耦合响应的影响[J]. 航空动力学报,2025, 40(2):20230228. CHENG Jingli,HUANG Sheng,ZHOU Li,et al. Investigation on influence mechanism of aspect ratio on thermal-solid interaction response of serpentine nozzle[J]. Journal of Aerospace Power,2025, 40(2):20230228. (in ChineseCHENG Jingli, HUANG Sheng, ZHOU Li, et al. Investigation on influence mechanism of aspect ratio on thermal-solid interaction response of serpentine nozzle[J]. Journal of Aerospace Power, 2025, 40(2): 20230228. (in Chinese) [20] 程经理,黄盛,周莉,等. 第一弯出口面积比对 S 弯喷管热固耦合响应影响研究[J]. 航空动力学报,2025, 40(3):20230229. CHENG Jingli,HUANG Sheng,ZHOU Li,et al. Investigation on influence mechanism of area ratio of first bend on thermal-solid interaction reponse of serpentine nozzle[J]. Journal of Aerospace Power,2025, 40(3):20230229. (in ChineseCHENG Jingli, HUANG Sheng, ZHOU Li, et al. Investigation on influence mechanism of area ratio of first bend on thermal-solid interaction reponse of serpentine nozzle[J]. Journal of Aerospace Power, 2025, 40(3): 20230229. (in Chinese) [21] SUN X L,WANG Z X,ZHOU L,et al. Influences of design parameters on a double serpentine convergent nozzle[J]. Journal of Engineering for Gas Turbines and Power,2016,138(7): 072301. doi: 10.1115/1.4032338 [22] 孙啸林. 低可探测S弯喷管设计及性能评估方法研究[D]. 西安: 西北工业大学,2018. SUN Xiaolin. Investigation on design method and performance estimation of low observable S-shaped nozzle[D]. Xi’an: Northwestern Polytechnical University,2018. (in ChineseSUN Xiaolin. Investigation on design method and performance estimation of low observable S-shaped nozzle[D]. Xi’an: Northwestern Polytechnical University, 2018. (in Chinese) [23] 程稳. S弯喷管红外辐射特性预测及优化设计方法[D]. 西安: 西北工业大学,2019. CHENG Wen. Infrared signature prediction and optimization design method for serpentine nozzle[D]. Xi’an: Northwestern Polytechnical University,2019. (in ChineseCHENG Wen. Infrared signature prediction and optimization design method for serpentine nozzle[D]. Xi’an: Northwestern Polytechnical University, 2019. (in Chinese) [24] 夏刚,刘新建,程文科,等. 钝体高超声速气动加热与结构热传递耦合的数值计算[J]. 国防科技大学学报,2003,25(1): 35-39. XIA Gang,LIU Xinjian,CHENG Wenke,et al. Numerical simulation of coupled aeroheating and solid heat penetration for a hypersonic blunt body[J]. Journal of National University of Defense Technology,2003,25(1): 35-39. (in Chinese doi: 10.3969/j.issn.1001-2486.2003.01.008XIA Gang, LIU Xinjian, CHENG Wenke, et al. Numerical simulation of coupled aeroheating and solid heat penetration for a hypersonic blunt body[J]. Journal of National University of Defense Technology, 2003, 25(1): 35-39. (in Chinese) doi: 10.3969/j.issn.1001-2486.2003.01.008 [25] Fraunhofer Institute for Algorithms and Scientific Computing. MPCCI: mesh based parallel code coupling interface 4.1.0 user manual [R]. Sankt Augustin,German: Fraunhofer Institute for Algorithms and Scientific Computing,2011. [26] WIETING A. Experimental study of shock wave interference heating on a cylindrical leading edge: NASA-TM-100484 [R]. Hampton,US: NASA Langley Research Center,1987. [27] DECHAUMPHAI P,THORNTON E A,WIETING A R. Flow-thermal-structural study of aerodynamically heated leading edges[J]. Journal of Spacecraft and Rockets,1989,26(4): 201-209. doi: 10.2514/3.26055 [28] DECHAUMPHAI P,WIETING A,THORNTON E. Flow-thermal-structural study of aerodynamically heated leading edges: AIAA 1988-2245 [R]. Reston,US: AIAA,1988. [29] 郭帅. 高超声速飞行器关键部件的多物理场耦合研究[D]. 南京: 南京航空航天大学,2016. GUO Shuai. Multidisciplinary study of key components in hypersonic flight vehicle[D]. Nanjing: Nanjing University of Aeronautics and Astronautics,2016. (in ChineseGUO Shuai. Multidisciplinary study of key components in hypersonic flight vehicle[D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2016. (in Chinese) [30] 黄杰. 高超声速飞行器流热固多物理场耦合计算研究[D]. 哈尔滨: 哈尔滨工业大学,2013. HUANG Jie. Study on hypersonic vehicle fluid-thermal-structure multi-physics coupling calculation[D]. Harbin: Harbin Institute of Technology,2013. (in ChineseHUANG Jie. Study on hypersonic vehicle fluid-thermal-structure multi-physics coupling calculation[D]. Harbin: Harbin Institute of Technology, 2013. (in Chinese) [31] BILLIG F S. Shock-wave shapes around spherical-and cylindrical-nosed bodies[J]. Journal of Spacecraft and Rockets,1967,4(6): 822-823. doi: 10.2514/3.28969 [32] ZOPE A D,SCHEMMEL A,BHATIA M,et al. Development and validation of fluid-thermal interaction solver for high fidelity transient simulations: AIAA2020-3006 [R]. Reston,US: AIAA,2020. [33] KAMALI S,MAVRIPLIS D J,ANDERSON E M. Development and validation of a high-fidelity aero-thermo-elastic analysis capability: AIAA2020-1449 [R]. Reston,US: AIAA,2020. [34] LEE C,BOEDICKER C. Subsonic diffuser design and performance for advanced fighter aircraft: AIAA1985-3073 [R]. Reston,US: AIAA,1985. [35] 李君哲,阎超,柯伦,等. 气动热CFD计算的格式效应研究[J]. 北京航空航天大学学报,2003,29(11): 1022-1025. LI Junzhe,YAN Chao,KE Lun,et al. Research on scheme effect of computational fluid dynamics in aerothermal[J]. Journal of Beijing University of Aeronautics and Astronautics,2003,29(11): 1022-1025. (in Chinese doi: 10.3969/j.issn.1001-5965.2003.11.014LI Junzhe, YAN Chao, KE Lun, et al. Research on scheme effect of computational fluid dynamics in aerothermal[J]. Journal of Beijing University of Aeronautics and Astronautics, 2003, 29(11): 1022-1025. (in Chinese) doi: 10.3969/j.issn.1001-5965.2003.11.014 [36] 潘沙. 高超声速气动热数值模拟方法及大规模并行计算研究[D]. 长沙: 国防科学技术大学,2010. PAN Sha. Hypersonic aerothermal numerical simulation method and massive parallel computation research[D]. Changsha: National University of Defense Technology,2010. (in ChinesePAN Sha. Hypersonic aerothermal numerical simulation method and massive parallel computation research[D]. Changsha: National University of Defense Technology, 2010. (in Chinese) -
点击查看大图
计量
- 文章访问数: 237
- HTML浏览量: 130
- PDF量: 35
- 被引次数: 0