Simulation and experimental study on radial temperature distribution control technology based on flame tube cooling holes
-
摘要:
为有效降低燃烧室出口叶尖温度进而保障发动机涡轮叶片叶冠断裂故障的顺利解决，对燃烧室开展了基于火焰筒冷却孔的径向温度分布控制仿真及试验研究。通过流场与流量分配分析，提出外环第8排冷却孔几何面积增加65.3%的控制方案。数值仿真表明：控制方案使该孔流量占比提升60.63%，其余进气结构流量占比相应减少2.95%～3.45%，出口叶尖温度显著降低56 K。部件与整机试验进一步验证了方案的有效性。部件试验显示，控制方案叶尖温度较原型降低51 K，出口温度径向分布呈现叶尖与叶根温度较低、约2/3叶高处达峰值的特征，出口温度分布系数（OTDF）、径向温度分布系数（RTDF）均满足设计要求，且未对燃烧室其他关键性能产生不利影响，将有利于涡轮叶片可靠性。仿真与部件试验的温度分布趋势一致性较好，为燃烧室出口温度场的精准控制提供了一种有效技术路径。
Abstract:In order to effectively reduce the tip temperature at the combustion chamber outlet and ensure smooth resolution of the turbine blade tip crown fracture failure, a simulation and experimental study on the radial temperature distribution control based on the cooling holes of the flame tube was conducted for the combustion chamber. Through analysis of the flow field and flow distribution, a control scheme was proposed to increase the geometric area of the 8th row of cooling holes in the outer ring by 65.3%. The numerical simulation results showed that this scheme increased the proportion of hole flow by 60.63%, while the proportion of flow in other intake structures decreased by 2.95% to 3.45% accordingly, and the temperature at the outlet blade tip was significantly reduced by 56 K. Component tests and complete machine tests further verified the effectiveness of the scheme. Component tests showed that the tip temperature of the control scheme was 51 K lower than that of the prototype, and the radial distribution of the outlet temperature presented the characteristics of lower temperatures at the tip and root, with the peak at about 2/3 of the blade height. Both outlet temperature distribution factor（OTDF） and radial temperature distribution factor（RTDF） met the design requirements, and the scheme did not have adverse effect on other key performances of the combustion chamber, which was beneficial to the reliability of the turbine blade. The temperature distribution trends of the simulation and component tests were consistent, providing an effective technical path for the precise control of the combustion chamber outlet temperature field.
-
图 2 原型燃烧室出口温度场径向分布试验数据
Figure 2. Experimental data on the radial distribution of temperature field at the outlet of the prototype combustor
图 4 原型燃烧室出口温度场径向分布试验与仿真数据
Figure 4. Experimental and simulation data on the radial distribution of temperature field at the outlet of the prototype combustor
图 5 原型、控制方案过涡流器中心截面温度场分布仿真数据
Figure 5. Simulation data of temperature field distribution on the cross-section passing through the center of the swirl cup for the prototype and control scheme
图 6 原型、控制方案燃烧室出口温度场分布仿真数据
Figure 6. Simulation data of temperature field distribution at the combustor outlet for the prototype and control scheme
图 7 原型、控制方案燃烧室出口温度场径向分布仿真数据
Figure 7. Simulation data of radial temperature distribution at the combustor outlet for the prototype and control scheme
图 10 旋转测温装置总温、总压感头分布
Figure 10. Distribution of total temperature and total pressure feeling heads of rotary measuring device
图 11 原型、控制方案燃烧室出口温度场分布试验数据
Figure 11. Experimental data of temperature field distribution at the combustor outlet for the prototype and control scheme
图 12 原型、控制方案燃烧室出口温度径向分布试验与仿真数据
Figure 12. Experimental and simulation data of radial temperature distribution at the combustor outlet for the prototype and control scheme
图 13 热电偶测温耙安装及测温环面示意图
Figure 13. Installation of thermocouple temperature measuring rake and schematic diagram of temperature measuring ring surface
图 14 涡轮支撑通道测量截面整机试验84点温度场分布试验数据
Figure 14. Experimental data of 84-point temperature field distribution at the turbine support duct measurement section from full-annulus rig tests
图 15 涡轮后环面平均与场平均温差分布试验数据
Figure 15. Experimental data of temperature difference distribution between annular average and field average at the turbine rear section
表 1 测量设备及精度
Table 1. Measure of equipment and precision
测量项目及参数 测量设备 设备精度 试验要求精度/% 试验数据采集 数据采集系统 ±0.1%FS 无 燃烧室进口静压、进出口总压 压力扫描阀 ±0.05%FS ±0.5 大气压力 PTB110传感器 ±0.05%FS ±0.5 燃烧室进口总温 K型热电偶 ±0.4%
|T−273.15|±1 燃烧室出口总温 B型热电偶 ±0.25%
|T−273.15|±2 燃烧室进口空气流量 标准喷嘴 ±1.5% ±1.5 喷嘴燃油流量 质量流量计 ±0.2%FS ±0.5 
下载: 导出CSV
-
[1] 李军, 栗智宇, 李志刚, 等. 燃烧室和涡轮相互作用下高压涡轮级气热性能研究进展[J]. 航空学报, 2021, 42(3): 024111. LI Jun, LI Zhiyu, LI Zhigang, et al. Aerothermal performance of high pressure turbine stage with combustor-turbine interactions: Review[J]. Acta Aeronautica et Astronautica Sinica, 2021, 42(3): 024111. (in ChineseLI Jun, LI Zhiyu, LI Zhigang, et al. Aerothermal performance of high pressure turbine stage with combustor-turbine interactions: Review[J]. Acta Aeronautica et Astronautica Sinica, 2021, 42(3): 024111. (in Chinese) [2] 陈炫午, 曾青华, 甘晓华. 航空发动机高温升燃烧室技术分析[J]. 推进技术, 2023, 44(2): 2208054. CHEN Xuanwu, ZENG Qinghua, GAN Xiaohua. Analysis of combustion technology of high temperature rise for aero engines[J]. Journal of Propulsion Technology, 2023, 44(2): 2208054. (in Chinese doi: 10.13675/j.cnki.tjjs.2208054CHEN Xuanwu, ZENG Qinghua, GAN Xiaohua. Analysis of combustion technology of high temperature rise for aero engines[J]. Journal of Propulsion Technology, 2023, 44(2): 2208054. (in Chinese) doi: 10.13675/j.cnki.tjjs.2208054 [3] 郑剑文, 江立军, 刘涛, 等. 旋流器套筒扩张角对燃烧室出口温度分布的影响[J]. 航空动力学报, 2024, 39(10): 20240164. ZHENG Jianwen, JIANG Lijun, LIU Tao, et al. Effects of swirler sleeve angle on combustor exit temperature distribution[J]. Journal of Aerospace Power, 2024, 39(10): 20240164. (in Chinese doi: 10.13224/j.cnki.jasp.20240164ZHENG Jianwen, JIANG Lijun, LIU Tao, et al. Effects of swirler sleeve angle on combustor exit temperature distribution[J]. Journal of Aerospace Power, 2024, 39(10): 20240164. (in Chinese) doi: 10.13224/j.cnki.jasp.20240164 [4] 江立军, 曹俊, 严明超, 等. 套筒配合间隙对燃烧室出口温度场品质的影响[J]. 推进技术, 2016, 37(6): 1015-1021. JIANG Lijun, CAO Jun, YAN Mingchao, et al. Effects of gap height between sleeve and baffle on combustor exit temperature distribution[J]. Journal of Propulsion Technology, 2016, 37(6): 1015-1021. (in Chinese doi: 10.13675/j.cnki.tjjs.2016.06.003JIANG Lijun, CAO Jun, YAN Mingchao, et al. Effects of gap height between sleeve and baffle on combustor exit temperature distribution[J]. Journal of Propulsion Technology, 2016, 37(6): 1015-1021. (in Chinese) doi: 10.13675/j.cnki.tjjs.2016.06.003 [5] 吕亚亚, 宗超, 朱彤, 等. 旋流器和射流孔流通面积对燃烧室流场及温度场影响的数值研究[J]. 热能动力工程, 2019, 34(2): 54-62. LYU Yaya, ZONG Chao, ZHU Tong, et al. Numerical investigation on the effect of the flow area of the swirler and jet holes on flow field and temperature field in combustion chamber[J]. Journal of Engineering for Thermal Energy and Power, 2019, 34(2): 54-62. (in Chinese doi: 10.16146/j.cnki.rndlgc.2019.02.008LYU Yaya, ZONG Chao, ZHU Tong, et al. Numerical investigation on the effect of the flow area of the swirler and jet holes on flow field and temperature field in combustion chamber[J]. Journal of Engineering for Thermal Energy and Power, 2019, 34(2): 54-62. (in Chinese) doi: 10.16146/j.cnki.rndlgc.2019.02.008 [6] 胡好生, 赵坚行, 钟建平, 等. 一种新颖的燃烧室出口温度场调试方法[J]. 航空动力学报, 2007, 22(8): 1222-1226. HU Haosheng, ZHAO Jianxing, ZHONG Jianping, et al. A new adjustment method of combustor outlet temperature field[J]. Journal of Aerospace Power, 2007, 22(8): 1222-1226. (in Chinese doi: 10.3969/j.issn.1000-8055.2007.08.003HU Haosheng, ZHAO Jianxing, ZHONG Jianping, et al. A new adjustment method of combustor outlet temperature field[J]. Journal of Aerospace Power, 2007, 22(8): 1222-1226. (in Chinese) doi: 10.3969/j.issn.1000-8055.2007.08.003 [7] 林宏军, 程明. 喷嘴匹配方案及火焰筒开孔对燃烧室性能影响的试验研究[J]. 航空发动机, 2012, 38(5): 13-17. LIN Hongjun, CHENG Ming. Effect of nozzle matching and flame tube holes on combustion performance[J]. Aeroengine, 2012, 38(5): 13-17. (in Chinese doi: 10.3969/j.issn.1672-3147.2012.05.005LIN Hongjun, CHENG Ming. Effect of nozzle matching and flame tube holes on combustion performance[J]. Aeroengine, 2012, 38(5): 13-17. (in Chinese) doi: 10.3969/j.issn.1672-3147.2012.05.005 [8] 徐榕, 赵坚行, 王锁芳. 主燃孔射流对模型燃烧室流动及燃烧影响的数值研究[J]. 航空动力学报, 2014, 29(6): 1312-1322. XU Rong, ZHAO Jianxing, WANG Suofang. Numerical study of influences of primary jets on turbulent flows and spray combustion in model combustor[J]. Journal of Aerospace Power, 2014, 29(6): 1312-1322. (in Chinese doi: 10.13224/j.cnki.jasp.2014.06.008XU Rong, ZHAO Jianxing, WANG Suofang. Numerical study of influences of primary jets on turbulent flows and spray combustion in model combustor[J]. Journal of Aerospace Power, 2014, 29(6): 1312-1322. (in Chinese) doi: 10.13224/j.cnki.jasp.2014.06.008 [9] 伍智. 高温升燃烧室出口温度场掺混孔调控技术研究[D]. 南京: 南京航空航天大学, 2013. WU Zhi. Investigation on technology of regulating outlet temperature field of high temperature rise combustors with dilution holes[D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2013. (in ChineseWU Zhi. Investigation on technology of regulating outlet temperature field of high temperature rise combustors with dilution holes[D]. Nanjing: Nanjing University of Aeronautics and Astronautics, 2013. (in Chinese) [10] 申力鑫. 掺混孔几何参数对燃烧室出口特性的影响[D]. 沈阳: 沈阳航空航天大学, 2018. SHEN Lixin. Influence of the geometrical parameters of mixing holes on the exit characteristics of the combustor[D]. Shenyang: Shenyang Aerospace University, 2018. (in ChineseSHEN Lixin. Influence of the geometrical parameters of mixing holes on the exit characteristics of the combustor[D]. Shenyang: Shenyang Aerospace University, 2018. (in Chinese) [11] PANG Liyao, ZHAO Ningbo, XU Honghao, et al. Numerical simulations on effect of cooling hole diameter on the outlet temperature distribution for a gas turbine combustor[J]. Applied Thermal Engineering, 2023, 234: 121308. doi: 10.1016/j.applthermaleng.2023.121308 [12] 杨欢, 郭舒, 詹政德, 等. 冷却孔结构对燃烧室性能和壁面冷却效果影响的数值模拟研究[J]. 西安交通大学学报, 2024, 58(11): 98-108. YANG Huan, GUO Shu, ZHAN Zhengde, et al. Numerical simulation research on the influence of cooling hole structure on combustor performance and liner wall cooling effect[J]. Journal of Xi’an Jiaotong University, 2024, 58(11): 98-108. (in Chinese doi: 10.7652/xjtuxb202411009YANG Huan, GUO Shu, ZHAN Zhengde, et al. Numerical simulation research on the influence of cooling hole structure on combustor performance and liner wall cooling effect[J]. Journal of Xi’an Jiaotong University, 2024, 58(11): 98-108. (in Chinese) doi: 10.7652/xjtuxb202411009 [13] 党新宪, 赵坚行, 吉洪湖. 试验研究双旋流器头部燃烧室几何参数对燃烧性能影响[J]. 航空动力学报, 2007, 22(10): 1639-1645. DANG Xinxian, ZHAO Jianxing, JI Honghu. Experimental study of effects of geometric parameters on combustion performance of dual-stage swirler combustor[J]. Journal of Aerospace Power, 2007, 22(10): 1639-1645. (in Chinese doi: 10.3969/j.issn.1000-8055.2007.10.009DANG Xinxian, ZHAO Jianxing, JI Honghu. Experimental study of effects of geometric parameters on combustion performance of dual-stage swirler combustor[J]. Journal of Aerospace Power, 2007, 22(10): 1639-1645. (in Chinese) doi: 10.3969/j.issn.1000-8055.2007.10.009 [14] 党新宪, 赵坚行, 颜应文, 等. 主燃孔对模型燃烧室流场的影响[J]. 推进技术, 2010, 31(1): 24-28, 41. DANG Xinxian, ZHAO Jianxing, YAN Yingwen, et al. Effects of different primary holes on flow fields within the model combustor[J]. Journal of Propulsion Technology, 2010, 31(1): 24-28, 41. (in Chinese doi: 10.13675/j.cnki.tjjs.2010.01.010DANG Xinxian, ZHAO Jianxing, YAN Yingwen, et al. Effects of different primary holes on flow fields within the model combustor[J]. Journal of Propulsion Technology, 2010, 31(1): 24-28, 41. (in Chinese) doi: 10.13675/j.cnki.tjjs.2010.01.010 [15] 党新宪, 赵坚行, 吉洪湖. 双旋流器燃烧室NOx生成研究[J]. 航空动力学报, 2008, 23(3): 430-435. DANG Xinxian, ZHAO Jianxing, JI Honghu. A study on NOx formation for double swirler combustor[J]. Journal of Aerospace Power, 2008, 23(3): 430-435. (in ChineseDANG Xinxian, ZHAO Jianxing, JI Honghu. A study on NOx formation for double swirler combustor[J]. Journal of Aerospace Power, 2008, 23(3): 430-435. (in Chinese) [16] GE Bing, JI Yongbin, CHI Zhongran, et al. Effusion cooling characteristics of a model combustor liner at non-reacting/reacting flow conditions[J]. Applied Thermal Engineering, 2017, 113: 902-911. doi: 10.1016/j.applthermaleng.2016.11.049 [17] ANDREINI A, BECCHI R, FACCHINI B, et al. The effect of effusion holes inclination angle on the adiabatic film cooling effectiveness in a three-sector gas turbine combustor rig with a realistic swirling flow[J]. International Journal of Thermal Sciences, 2017, 121: 75-88. doi: 10.1016/j.ijthermalsci.2017.07.003 [18] 杨光, 邵卫卫, 张哲巅. 孔布局对切向发散结构综合冷却效率的影响[J]. 推进技术, 2023, 44(5): 2204069. YANG Guang, SHAO Weiwei, ZHANG Zhedian. Effects of hole arrangement on overall cooling effectiveness for tangential effusion cooling[J]. Journal of Propulsion Technology, 2023, 44(5): 2204069. (in Chinese doi: 10.13675/j.cnki.tjjs.2204069YANG Guang, SHAO Weiwei, ZHANG Zhedian. Effects of hole arrangement on overall cooling effectiveness for tangential effusion cooling[J]. Journal of Propulsion Technology, 2023, 44(5): 2204069. (in Chinese) doi: 10.13675/j.cnki.tjjs.2204069 [19] 宋波, 林宇震, 刘高恩, 等. 不同排列方式多斜孔壁气膜冷却绝热温比研究[J]. 航空动力学报, 1999, 14(1): 91-94. SONG Bo, LIN Yuzhen, LIU Gaoen, et al. An investigation on film cooling effectiveness of inclined-mutihole walls with different patterns[J]. Journal of Aerospace Power, 1999, 14(1): 91-94. (in Chinese doi: 10.3969/j.issn.1000-8055.1999.01.022SONG Bo, LIN Yuzhen, LIU Gaoen, et al. An investigation on film cooling effectiveness of inclined-mutihole walls with different patterns[J]. Journal of Aerospace Power, 1999, 14(1): 91-94. (in Chinese) doi: 10.3969/j.issn.1000-8055.1999.01.022 [20] 李广超, 朱惠人, 白江涛, 等. 气膜孔布局对前缘气膜冷却效率影响的实验[J]. 推进技术, 2008, 29(2): 153-157. LI Guangchao, ZHU Huiren, BAI Jiangtao, et al. Experimental investigation of film cooling effectiveness on leading edge with various geometries[J]. Journal of Propulsion Technology, 2008, 29(2): 153-157. (in Chinese doi: 10.3321/j.issn:1001-4055.2008.02.006LI Guangchao, ZHU Huiren, BAI Jiangtao, et al. Experimental investigation of film cooling effectiveness on leading edge with various geometries[J]. Journal of Propulsion Technology, 2008, 29(2): 153-157. (in Chinese) doi: 10.3321/j.issn:1001-4055.2008.02.006 [21] 杨光, 邵卫卫, 张哲巅. 新型切向发散孔气膜冷却特性数值研究[J]. 推进技术, 2022, 43(11): 210579. YANG Guang, SHAO Weiwei, ZHANG Zhedian. Numerical investigation on film cooling performance of novel tangential effusion holes[J]. Journal of Propulsion Technology, 2022, 43(11): 210579. (in Chinese doi: 10.13675/j.cnki.tjjs.210579YANG Guang, SHAO Weiwei, ZHANG Zhedian. Numerical investigation on film cooling performance of novel tangential effusion holes[J]. Journal of Propulsion Technology, 2022, 43(11): 210579. (in Chinese) doi: 10.13675/j.cnki.tjjs.210579 [22] WANG Tianyi, XUAN Yimin, HAN Xingsi. Investigation on hybrid thermal features of aero-engines from combustor to turbine[J]. International Journal of Heat and Mass Transfer, 2023, 200: 123559. doi: 10.1016/j.ijheatmasstransfer.2022.123559 [23] DAI Huwei, ZHANG Junhong, REN Yanyan, et al. Effect of cooling hole configurations on combustion and heat transfer in an aero-engine combustor[J]. Applied Thermal Engineering, 2021, 182: 115664. doi: 10.1016/j.applthermaleng.2020.115664 [24] KUNDU K, DEUR J. A simplified reaction mechanism for calculation of emissions in hydrocarbon (Jet-A) combustion: AIAA1993-2341 [R]. Monterey, US: AIAA, 1993. [25] 蒋尧, 彭中九, 王志凯, 等. 基于分层验证和火焰面生成流模型的燃烧室出口温度场仿真[J]. 推进技术, 2024, 45(8): 2305023. JIANG Yao, PENG Zhongjiu, WANG Zhikai, et al. Numerical simulation of combustor outlet temperature distribution based on hierarchical validation method and FGM model[J]. Journal of Propulsion Technology, 2024, 45(8): 2305023. (in Chinese doi: 10.13675/j.cnki.tjjs.2305023JIANG Yao, PENG Zhongjiu, WANG Zhikai, et al. Numerical simulation of combustor outlet temperature distribution based on hierarchical validation method and FGM model[J]. Journal of Propulsion Technology, 2024, 45(8): 2305023. (in Chinese) doi: 10.13675/j.cnki.tjjs.2305023 -
点击查看大图
计量
- 文章访问数: 230
- HTML浏览量: 111
- PDF量: 32
- 被引次数: 0