涡轮叶片尾缘开缝喷气的数值模拟和试验研究

王掩刚; 刘波; 姜健; 陈云永

涡轮叶片尾缘开缝喷气的数值模拟和试验研究

西北工业大学翼型叶栅空气动力学国防重点实验室, 陕西西安 710072

基金项目: 国家自然科学基金资助(59976032)

计量
- 文章访问数: 1743
- HTML浏览量: 3
- PDF量: 505
- 被引次数: 0
出版历程
- 收稿日期: 2005-04-01
- 修回日期: 2005-06-09
- 刊出日期: 2006-06-28

Experiment and Numerical Simulation Investigation of Turbine Blade with Trailing Edge Ejection

National Laboratory of Airfoil and Cascade Aero-Dynamic, Northwestern Polytechnical University, Xi'an 710072, China

摘要

摘要: 以某涡轮叶栅为研究对象,采用试验和数值模拟相结合的方式研究了涡轮叶片尾缘不同喷气形式对叶栅性能的影响。应用一维源项喷气模型,结合涡轮叶栅流场数值模拟,得到了不同喷气形式下涡轮叶栅流场细节。计算与试验结果显示:两种开缝形式下,喷气比例对叶片表面参数以及出口气流角影响不大,但能量损失系数随着喷气比例的增大出现先增大后减小的趋势。对开缝时,喷气引入吹除了附着在叶片尾缘的漩涡,并增强了尾迹与主流的掺混过程;半开缝时,喷气的引入仅吹除了附着在开缝处的漩涡,对于尾缘处流场影响不大。
- 航空、航天推进系统 /
- 涡轮叶栅 /
- 对开缝 /
- 半开缝 /
- 喷气 /
- 能量损失系数
Abstract: Numerical simulations and tests were carried out to investigate the effect of ejection from different trailing edge slots of a turbine cascade.The detailed flow field of ejection cascade was obtained by using a compact ejection model coupled with the calculation of main flow field.Numerical and experimental results show that the ejection ratio has little effect on the distribution of Mach number and exit flow angle of the two slot types.However,the energy degradation coefficient increases at first and then it has a decreasing tendency with the increase of ejection ratio.The ejection from the symmetric slot blows away the vortex at the blade trailing edge and strengthens the mixing of the wake with the main flow.The ejection from the half slot only blows away the vortex on the slot surface,and has little effect on the flow field near the trailing edge.
- aerospace propulsion system /
- turbine cascade /
- symmetric slot /
- half slot /
- ejection /
- energy degradation coefficient

HTML

参考文献(9)

[1]	Cornelis Kapteijn and Jochen Amecke,Aerodynamic Performance of a Transonic Turbine Guide Vane with Trailing Edge Coolant Ejection:Part I-Experimental Approach[R].ASME PAPER 94-GT-288.
[2]	Wilfert G,Fottner L.The Aerodynamic Mixing Effect of Discrete Cooling Jets with Mainstream Flow on a Highly Loaded Turbine Blade[R].ASME 1994:94-GT-235.
[3]	Gritsch M,Schulz A,Writing S.Adiabatic Wall Effectiveness Measurement of Film-Cooling Holes with Expanded Exits[J].ASM E Jouranl Turbomachinary,1998,549～556.
[4]	Oguz Uzol.Aerodynamic Loss Characteristics of a Turbine Blade with Trailing Edge Coolant Ejection:Part Ⅱ-External Aerodynamics,Total Pressure Losses,and Predictions[J].Journal of Turbomachinary,April,2001,123:238～ 248.
[5]	朱惠人,许都纯,刘松龄,气膜孔形状对排孔下游换热的影响,航空动力报[J].2001,16(4):360～364.Zhu Huiren,Xu Duchun,Liu Songling.Effects of Film Cooling Hole Shape on Heat Transfer[J].Journal of Aerospace Power,2001,16(4):360～364.
[6]	王掩刚.叶片尾缘开缝喷气对流场干扰和掺混效应的研究[D].陕西西安:西北工业大学,2004.
[7]	Jameson A.Lower-Upper Implicit Schemes with Multiple Grids for the Euler Equations[R].AIAA 1987.
[8]	Martelli F,Michelassi V,Boretti A A.Numerical Modeling of Coolant Jet Flow in Turbine Cascades[R].Revue Francaise de Mecanique,1992.
[9]	王掩刚,梅运焕,刘波.计算涡轮叶片尾缘对开缝喷气的数值方法,推进技术[J].2002,23(4)315～317.Wang Yangang,Mei Yunhuan,Liu Bo.Numerical Approach for Turbine Blade with Trailing Edge Ejection[J].Journal of Propulsion Technology,2002,23(4):315～317.