楔形肋片内冷通道传热与流动阻力特性

邱庆刚; 王海鹏; 赵亮; 沈胜强

楔形肋片内冷通道传热与流动阻力特性

大连理工大学能源与动力学院, 辽宁大连 116024

基金项目: 辽宁省博士科研启动基金(20091011)

计量
- 文章访问数: 1719
- HTML浏览量: 1
- PDF量: 5
- 被引次数: 0
出版历程
- 收稿日期: 2011-01-06
- 修回日期: 2011-03-23
- 刊出日期: 2011-12-28

Heat transfer and friction behavior in internal cooling duct with cuniform-fins

School of Energy and Power Engineering, Dalian University of Technology, Dalian Liaoning 116024, China

摘要

摘要: 利用实验和数值模拟方法,分析了楔形肋片几何结构对仿螺旋肋片内冷通道强化传热与流动阻力特性的影响,并将模拟结果与实验数据进行了对比,两者结果吻合良好.研究结果表明,随着楔形肋片导流角的增大,通道的强化传热显著增强,但其流动阻力也明显增大;气流方向的不同对通道总体换热强度影响不是很大,但反吹时通道中的流动阻力却明显高于正吹;从内冷通道的综合换热效果来看,当楔形肋片导流角为7?且气流正吹时是最佳的肋片几何结构参数.
- 叶片冷却 /
- 燃气轮机 /
- 楔形仿螺旋肋片 /
- 传热强化 /
- 对流换热
Abstract: Experimental and numerical methods were applied together to investigate the influence of cuniform-fin geometry parameters on heat transfer and friction behavior in helix-alike internal cooling channel of the gas turbine blades.The numerical results were compared with the experimental data,and they agreed very well with each other.Results show that,with the increase of helix-alike fin leading angle,heat transfer enhancement is improved more significantly and at the mean time pressure penalty also becomes higher in the internal cooling duct.The results also indicate that air flow direction has less effect on heat transfer enhancement,but the flow resistance with reverse coolant direction is markedly higher than that with normal coolant direction.In addition,based on the results of the numerical simulation,the configuration of fins with leading angle 7? and fluid flow with normal coolant direction give the best overall performance.
- blade cooling /
- gas turbine /
- helix-alike cuniform-fin /
- heat transfer enhancement /
- convective heat transfer

HTML

参考文献(13)

[1]	Xie G,Sundén B.Numerical predictions of augmented heat transfer of an internal blade tip-wall by hemispherical dimples[J].International Journal of Heat and Mass Transfer,2010,45(25-26):5639-5650.
[2]	Wang C C,Chen K.Forced convection in a wavy-wall channel[J].International Journal of Heat and Mass Transfer,2002,45(12):2587-2595.
[3]	Chang S W,Lees A W,Liou T M,et al.Heat transfer of a radially rotating furrowed channel with two opposite skewed sinusoidal wavy walls[J].International Journal of Thermal Sciences,2010,49(5):769-785.
[4]	吉洪湖,王宝官,王代军.涡轮叶片尾缘出流对带叉排扰流柱阵列的内冷通道传热特性的影响[J].航空动力学报,1999,14(3):237-241. JI Honghu,WANG Baoguan,WANG Daijun.Effect of trailing edge ejection of turbine blades on heat transfer of cooing passage with staggered pin fins[J].Journal of Aerospace Power,1999,14(3):237-241.(in Chinese)
[5]	田丽亭,关志强,凌长明,等.叉排针肋楔形通道换热数值研究[J].热科学与技术,2004,3(1):34-37. TIAN Liting,GUAN Zhiqiang,LING Changming,et al.Numerical investigation of heat transfer in wedge-shaped passage with staggered pin-fins[J].Journal of Thermal Science and Technology,2004,3(1):34-37.(in Chinese)
[6]	邓斌,Wong T T,陶文铨,等.带交叉肋方形截面通道内强制对流换热的实验研究[J].西安交通大学学报,2002,36(9):881-885. DENG Bin,Wong T T,TAO Wenquan,et al.Experimental study of forced convection in a rectangle duct with cross ribs on the opposite walls[J].Journal of Xi''''an Jiaotong University,2002,36(9):881-885.(in Chinese)
[7]	Chandra P R,Alexander C R,Han J C.Heat transfer and friction behaviors in rectangular channels with varying number of ribbed walls[J].International Journal of Heat and Mass Transfer,2003,46(3):481-495.
[8]	Tanda G.Heat transfer in rectangular channels with transverse and V-shaped broken ribs[J].International Journal of Heat and Mass Transfer,2004,47(2):229-243.
[9]	Iacovides H,Raisee M.Turbulent flow and heat transfer in stationary and rotating cooling passages with inclined ribs on opposite walls[J].International Journal of Numerical Methods for Heat and Fluid Flow,2008,18(2):258-278.
[10]	张勃,吉洪湖,张靖周,等.网格式肋化通道换热与总压损失特性研究[J].航空动力学报,2004,19(2):201-205. ZHANG Bo,JI Honghu,ZHANG Jingzhou,et al.Experimental study of heat transfer and total pressure drop of a grid-ribbed rectangular channel[J].Journal of Aerospace Power,2004,19(2):201-205.(in Chinese)
[11]	张勃,吉洪湖,张靖周,等.肋的几何参数对网格式肋化通道的传热与总压损失特性的影响[J].航空动力学报,2004,19(2):206-212. ZHANG Bo,JI Honghu,ZHANG Jingzhou,et al.Influence of rib''''s geometric parameters upon heat transfer and total pressure loss in grid-ribbed channel[J].Journal of Aerospace Power,2004,19(2):206-212.(in Chinese)
[12]	邱庆刚,沈胜强.肋片形状对仿螺旋肋片内冷通道流动与换热的影响[J].航空动力学报,2006,21(1):71-76. QIU Qinggang,SHEN Shengqiang.Effect of helix-alike fin surface shape on flow and heat transfer in the internal cooling passage[J].Journal of Aerospace Power,2006,21(1):71-76.(in Chinese)
[13]	邱庆刚,沈胜强,张博.带有倾斜楔形肋片的矩形内冷通道流动与传热数值分析[J].大连理工大学学报,2006,46(3):345-349. QIU Qinggang,SHEN Shengqiang,ZHANG Bo.Turbulent flow and heat transfer in rectangular passage with tilted wedged-fins[J].Journal of Dalian University of Technology,2006,46(3):345-349.(in Chinese)