留言板

尊敬的读者、作者、审稿人, 关于本刊的投稿、审稿、编辑和出版的任何问题, 您可以本页添加留言。我们将尽快给您答复。谢谢您的支持!

姓名
邮箱
手机号码
标题
留言内容
验证码

Development and calibration of heat transfer coefficient sensor for rotational state

QUAN Yong-kai,  XU Guo-qiang,  LUO Xiang,  ZHANG Da

downloadPDF
文章导航 > 航空动力学报  > 2011 >  26(12): 2684-2690
QUAN Yong-kai, XU Guo-qiang, LUO Xiang, ZHANG Da. Development and calibration of heat transfer coefficient sensor for rotational state[J]. 航空动力学报, 2011, 26(12): 2684-2690.
引用本文: QUAN Yong-kai, XU Guo-qiang, LUO Xiang, ZHANG Da. Development and calibration of heat transfer coefficient sensor for rotational state[J]. 航空动力学报, 2011, 26(12): 2684-2690.
shu
QUAN Yong-kai, XU Guo-qiang, LUO Xiang, ZHANG Da. Development and calibration of heat transfer coefficient sensor for rotational state[J]. Journal of Aerospace Power, 2011, 26(12): 2684-2690.
Citation: QUAN Yong-kai, XU Guo-qiang, LUO Xiang, ZHANG Da. Development and calibration of heat transfer coefficient sensor for rotational state[J]. Journal of Aerospace Power, 2011, 26(12): 2684-2690.
shu

Development and calibration of heat transfer coefficient sensor for rotational state

  • School of Jet Propulsion, Beijing University of Aeronautics and Astronautics, Beijing 100000, China

Development and calibration of heat transfer coefficient sensor for rotational state

  • School of Jet Propulsion, Beijing University of Aeronautics and Astronautics, Beijing 100000, China

    摘要
  • 摘要: A novel heat transfer coefficient sensor is introduced and the design, manufacture,and calibration are described.The intended application of this instrument was on a high rotational speed test disc. In the experiments,the heat transfer coefficient sensor was calibrated under static state and rotational state respectively. The calibration under the static state was accomplished in a pipe: the inside diameter (ID) was 0.048m and the total length was 4m, the distance between the sensor and the inlet of the pipe was 3.5m; the standard value was measured using a self-made calibrator. The calibration under the rotational state was accomplished using a rotating disc: the diameter and thickness of the stainless disc were 800mm and 25mm, respectively;the sensor was installed at the location of r =250mm; the rotating disc driven by a 30kW direct current motor can supply the maximum rotational speed of 3000r/min. The standard value under rotational state was provided by an approximate empirical formula. The results show that the designed sensor can measure heat transfer coefficient directly under rotational state and static state with good accuracy and stability; the correlation factor of K are constant under static state and rotational state.

     

    Abstract: A novel heat transfer coefficient sensor is introduced and the design, manufacture,and calibration are described.The intended application of this instrument was on a high rotational speed test disc. In the experiments,the heat transfer coefficient sensor was calibrated under static state and rotational state respectively. The calibration under the static state was accomplished in a pipe: the inside diameter (ID) was 0.048m and the total length was 4m, the distance between the sensor and the inlet of the pipe was 3.5m; the standard value was measured using a self-made calibrator. The calibration under the rotational state was accomplished using a rotating disc: the diameter and thickness of the stainless disc were 800mm and 25mm, respectively;the sensor was installed at the location of r =250mm; the rotating disc driven by a 30kW direct current motor can supply the maximum rotational speed of 3000r/min. The standard value under rotational state was provided by an approximate empirical formula. The results show that the designed sensor can measure heat transfer coefficient directly under rotational state and static state with good accuracy and stability; the correlation factor of K are constant under static state and rotational state.

     

    • HTML
    • 参考文献(17)
  • [1] Alexiou A,Hills N J,Long C A,et al.Heat transfer in high pressure compressor internal air systems:a rotating disc-cone cavity with axial throughflow[J].International Journal of Experimental Heat Transfer,2000,13(4):299-328.
    [2] Long C,Childs P.The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow[J].Journal of Aerospace Power,2007,22(5):683-693.
    [3] Long C A,Morse A P,Tucker P G.Measurement and computation of heat transfer in high pressure compressor drum geometries with axial throughflow[J].Journal of Turbomachinery,1997,119(1):51-60.
    [4] Owen J M.On the computation of heat transfer coefficients from imperfect temperature measurements[J].Journal of Mechanical Engineering Science,1979,21(5):323-334.
    [5] Long C A.The effect of thermocouple disturbance errors on the measurement of local heat transfer coefficients[C]//Proceedings of Test and Transducer Conference.United Kingdom:Wembley,1985:73-104.
    [6] Owen J M,Onur H S.Convective heat transfer in a rotating cylindrical cavity[J].Journal of Engineering for Power,1983,105: 265-271.
    [7] Farthing P R,Long C A,Owen J M,et al.Rotating cavity with axial thoughflow of coolig air:heat transfer[J].Journal of Turbomachinery,1992,114(1):229-236.
    [8] Long C A,Tucker P G.Shroud heat transfer measurements from a rotating cavity with an axial throughflow of air[J].Journal of Turbomachinery,1994,116(3):525-534.
    [9] Bohn D,Deuker E,Emunds R,et al.Experimental and theoretical investigations of heat transfer in closed gas filled rotating annuli[J].Journal of Turbomachinery,1995,117(1):175-183.
    [10] Bohn D,Dibelius G H,Deuker E,et al.Flow pattern and heat transfer in a closed rotating annulus[J].Journal of Turbomachinery,1994,116(3):542-547.
    [11] Amarante A,Lanoiselle J L.Heat transfer coefficients measurement in industrial reezing equipment by using heat flux sensors[J].Journal of Food Engineering,2005,66(3):377-386.
    [12] Delaplace G,Demeyre J F,Guerin R,et al.Determination of representative and instantaneous process side heat transfer coefficients in agitated vessel using heat flux sensors[J].Chemical Engineering and Processing,2005,44(9):993-998.
    [13] Harris M B,Lovatt S J,Willix J.Development of a sensor for measuring local heat transfer coefficients on carcass shaped objects[R].Sydney:The 20th International Congress of Refrigeration,1999.
    [14] Harris M B,Willix J,Lovatt S J.Development of a method for measuring local heat transfer coefficients on carcass shaped objects[R].Washington,DC:The 21st International Congress of Refrigeration,2003.
    [15] XU Guoqiang,TAO Zhi,DING Shuiting.A test method of heat transfer coefficient and a kind of heat transfer coefficient sensor:China,200410074334.x[P].2004-09-10.(in Chinese)
    [16] QUAN Yongkai,XU Guoqiang,LUO Xiang.Development of a kind of heat transfer coefficient sensor based on steady method[J].Journal of Beijing University of Aeronautics and Astronautics,2009,35(2):1413-1416.(in Chinese)
    [17] Dorfamn L A.Hydrodynamic resistance and the heat loss of rotating solids[M].London:Oliver and Boyd Ltd.,1963.
    • 相关文章
    • 施引文献
  • 资源附件(0)
  • 加载中
WeChat 点击查看大图
计量
  • 文章访问数:  1395
  • HTML浏览量:  3
  • PDF量:  10
  • 被引次数: 0
出版历程
  • 收稿日期:  2010-11-23
  • 修回日期:  2011-11-10
  • 刊出日期:  2011-12-28

目录

    /

    返回文章
    返回

    版权所有 © 《航空动力学报》编辑部

    本系统由 北京仁和汇智信息技术有限公司 开发