压力敏感涂料的标定及在气膜冷却效率测量中的应用

张超; 王湛; 周嗣京; 刘建军

压力敏感涂料的标定及在气膜冷却效率测量中的应用

张超^1,2,
王湛^1,2,
周嗣京¹,
刘建军¹

1.
中国科学院工程热物理研究所, 北京 100190
2.
中国科学院研究生院, 北京 100190

基金项目: 国家重点基础研究发展计划(2007CB210108)

计量
- 文章访问数: 1795
- HTML浏览量: 146
- PDF量: 17
- 被引次数: 0
出版历程
- 收稿日期: 2011-02-28
- 修回日期: 2011-05-25
- 刊出日期: 2011-12-28

Calibration of pressure-sensitive paint and application to the measurement of film cooling effectiveness

1.
Institute of Engineering Thermophysics, Chinese Academy of Sciences, Beijing 100190, China
2.
Graduate University of Chinese Academy of Sciences, Beijing 100190, China

摘要

摘要: 采用自行设计的标定装置对压力敏感涂料进行了标定实验,研究了激励光源光强、温度两种参数对标定曲线的影响.结果表明:当激励光源光强能够使得光敏分子发生氧猝熄条件下,激励光源光强对标定曲线的影响可以忽略不计;标定曲线对温度变化较为敏感.据此提出了采用二维插值方法得出发射光强关于压力比、温度比的表达式,从而对测量结果进行温度修正.在此基础上,将压力敏感涂料测试技术分别应用于圆柱孔、扇形孔气膜冷却效率的测量中,所得实验数据与前人结果符合较好.
- 压力敏感涂料 /
- 标定实验 /
- 激励光源光强 /
- 温度修正 /
- 气膜冷却
Abstract: Calibration of pressure sensitive paint was carried out by using the self-designed calibration setup.The influence of excitation light intensity and temperature on the calibration curve was investigated.The experimental results showed that the effect of excitation light intensity was negligible when the excitation light intensity was sufficient to cause the oxygen quenching of luminescent molecules,but the calibration curve was more sensitive to the temperature change.The expression of emission light intensity about pressure ratio and temperature ratio was proposed based on two-dimensional interpolation method,and the measurement results were corrected to account for temperature change effects.Then the pressure sensitive paint technology was applied to the film cooling effectiveness measurement of cylinder film hole and fan-shaped film hole,and the experimental results compared well with the previous experimental data.
- pressure-sensitive paint(PSP) /
- calibration experiment /
- excitation light intensity /
- temperature correction /
- film cooling

HTML

参考文献(13)

[1]	Kavandi J,Callis J,Gouterman M,et al.Luminescent barometry in wind tunnels[J].Review of Scientific Instruments,1990,61(11):3340-3347.
[2]	Gregory J W,Asai K,Kameda M,et al.A review of pressure-sensitive paint for high-speed and unsteady aerodynamics[J].Proceedings of the Institution of Mechanical Engineers,Part G:Journal of Aerospace Engineering,2008,222(2):249-290.
[3]	ZHOU Qiang,LIU Bo,GAO Limin,at al.Pressure measurement on suction surface of a single vane using pressure-sensitive paint[J].Chinese Journal of Aeronautics,2009,22(2):138-144.
[4]	Zhang L,Baltz M,Padupatty R,at al.Turbine nozzle film cooling study using the pressure sensitive paint (PSP) technique[R].ASME Paper No.99-GT-196,1999.
[5]	Varvel T A.Shaped hole effects on film cooling effectiveness and a comparison of multiple effectiveness measurement techniques[M].Texas:Texas A&M University,2004.
[6]	Gao Z H,Diganta N,Han J C.Turbine blade platform film cooling with typical stator-rotor purge flow and discrete-hole film cooling[R].ASME Paper GT2008-50286,2008.
[7]	Russin R A,Afred D,Wright L M.Measurement of detailed heat transfer coefficient and film cooling effectiveness distributions using PSP and TSP[R].ASME Paper GT2009-59975,2009.
[8]	李佳,韩昌,任静,等.基于压敏漆的带横槽气膜冷却实验与数值研究[J].工程热物理学报,2010,31(2):239-242. LI Jia,HAN Chang,REN Jing,et al.Film cooling performance of the embedded holes in trenches with compound angles[J].Journal of Engineering Thermophysics,2010,31(2):239-242.(in Chinese)
[9]	Liu T,Sullivan J P.Pressure and temperature sensitive paints[M].Berlin:Springer,2005.
[10]	Woodmansee M A,Dutton J C.Treating temperature-sensitivity effects of pressure-sensitive paint measurements[J].Experiments in Fluids,1998,24(2):163-174.
[11]	刘火星,余弦,陈怡,等.用于叶轮机内流测量的压力敏感涂料校准实验[J].工程热物理学报,2010,31(2):223-226. LIU Huoxing,YU Xian,CHEN Yi,et al.The calibration test of pressure sensitive paints in turbomcahinery flowfield measurement[J].Journal of Engineering Thermophysics,2010,31(2):223-226.(in Chinese)
[12]	高丽敏,王欢,刘波,等.光学压敏涂料的校准实验研究[C]//航空学会第十五届叶轮机专业委员会学会交流学会论文集.张家界:中国航空学会动力专业分会,2009:290-296.
[13]	Sinha A K,Bogard D G,Crawford M E.Film-cooling effectiveness downstream of a single row of holes with variable density ratio[J].ASME Journal of Turbomachinery,1991,113(3):442-449.