圆弧齿榫接结构应力的数值计算与分析

申秀丽; 周莹舻

圆弧齿榫接结构应力的数值计算与分析

北京航空航天大学能源与动力工程学院, 北京 100191

计量
- 文章访问数: 1559
- HTML浏览量: 58
- PDF量: 497
- 被引次数: 0
出版历程
- 收稿日期: 2011-04-03
- 修回日期: 2011-08-02
- 刊出日期: 2012-03-28

Numerical calculation and analysis of arc tooth tenon joint

School of Jet Propulsion, Beijing University of Aeronautics and Astronautics, Beijing 100191, China

摘要

摘要: 对两圆柱体接触问题和平面接触问题进行分析,探讨了接触区应力的收敛性.对某枞树形圆弧齿榫接结构的接触区应力进行了数值计算和分析.利用有限元软件ANSYS进行了接触分析,对比了梯形齿和圆弧齿榫接结构的应力结果,并采用光弹实验进行了验证.研究结果认为,与梯形齿榫接结构相比,圆弧齿榫接结构使接触应力、第三主应力和等效应力等降低.在此基础上,对圆弧齿榫接结构进行了优化分析,通过优化进一步降低了榫接结构的应力水平.
- 榫接结构 /
- 接触分析 /
- 梯形齿 /
- 圆弧齿 /
- 优化
Abstract: Two cylinders contact problem and plan contact problem were analyzed,and feature of convergence was discussed.Some numerical calculations of an arc tooth tenon joint with three teeth were done.Then,the contact stress with ANSYS was analyzed,and the results of trapezoid tooth and arc tooth tenon joint were compared to find that the latter decreased the contact stress,the third principle stress and von Mises stress.Based on this, some optimizations about the arc tooth tenon joint were done,and the stress was decreased again by optimization.
- tenon joint /
- contact analysis /
- trapezoid tooth /
- arc tooth /
- optimization

HTML

参考文献(14)

[1]	宋兆泓.航空燃气涡轮发动机强度设计[M].北京:北京航空航天大学出版社,2008.
[2]	Kosing O E,Scharl R,Shchmuhl H J.Design Improvements of the EJ200 HP compressor.ASME-2001-GT-0283,2001.
[3]	Meguid S A,Kanth P S,Czekanski A.Finite element analysis of fir-tree region in turbine discs[J].Finite Elements in Analysis and Design,2000,35(4):305-317.
[4]	SONG Wenbin,Keane A J.An efficient evolutionary optimisation framework applied to turbine blade firtree root local profiles[J].Structural Multidisciplinary Optimization,2005,29(5):382-390.
[5]	陈光.航空燃气涡轮发动机结构设计[M].北京:北京航空航天大学出版社,1988.
[6]	Sinclair G B,Cormier N G,Griffin J H,et al.Contact stresses in dovetail attachments:finite element modeling[J].Journal of Engineering for Gas Turbines and Power,2002,124(1):182-189.
[7]	Johnson.接触力学[M].徐秉业,罗学富,刘信声,译.北京:高等教育出版社,1992.
[8]	孙锡环,秦晓桐.烟气轮机盘榫槽部位的实验应力分析[J].北京理工大学学报,1996,16(4):361-366. SUN Xihuan,QIN Xiaotong.Stress analysis of experiment about mortise of flue gas turbine[J].Journal of Beijing Institute of Technology,1996,16(4):361-366.(in Chinese)
[9]	张如一.实验应力分析[M].北京:机械工业出版社,1982.
[10]	陈开军,马枚.航空发动机叶片榫头优化设计研究[J].航空动力学报,1995,10(2):190-192. CHEN Kaijun,MA Mei.Optimization of turbine blade fir-tree roots[J].Journal of Aerospace Power,1995,10(2):190-192.(in Chinese)
[11]	Song W,Keane A.Turbine blade fir-tree root design optimisation using intelligent CAD and finite element analysis[J].Computers and Structures,2002,80(24):1853-1867.
[12]	EGD-3斯贝MK202发动机应力标准[S].丁爱祥,吴君可,译.北京:国际航空编辑部,1979.
[13]	邢誉峰,诸德超.航空发动机涡轮盘榫槽的形状优化设计[J].航空学报,1995,16(4):488-491. XING Yufeng,ZHU Dechao.Shape optimization of aero engine disc groove[J].Acta Aeronautical et Astronautcia Sinica,1995,16(4):488-491.(in Chinese)
[14]	申秀丽,齐晓东.航空发动机涡轮榫接结构齿形基本参数研究[J].航空动力学报,2011,26(4):735-744. SHEN Xiuli,QI Xiaodong.Research of the basic parameters about tooth shape of tenon joint of aero engine turbine[J].Journal of Aerospace Power,2011,26(4):735-744.(in Chinese)