DD6单晶涡轮叶片缘板裂纹与再结晶研究

马健; 李世峰; 何爱杰; 曾军

DD6单晶涡轮叶片缘板裂纹与再结晶研究

中国航空工业集团公司中国燃气涡轮研究院涡轮技术研究室, 成都 610500

计量
- 文章访问数: 2222
- HTML浏览量: 98
- PDF量: 552
- 被引次数: 0
出版历程
- 收稿日期: 2011-07-03
- 刊出日期: 2012-05-28

Platform crack and recrystallization of DD6 single crystal turbine blade

Research Centre of Turbine Technology, China Gas Turbine Establishment, Aviation Industry Corporation of China, Chengdu 610500, China

摘要

摘要: 针对DD6单晶涡轮叶片在试车后缘板出现裂纹的现象,通过裂纹外观检查、断口形貌观察、显微组织及化学成分分析等工作,开展基于裂纹特征的缘板失效模式研究.研究结果表明:DD6单晶涡轮叶片缘板裂纹是由表面再结晶导致的疲劳开裂,其形成与存在富钨白色析出相的枝晶界面有直接关系;在试验条件下裂纹沿富钨(W)的白色颗粒链扩展,并沿界面延伸,导致疲劳失效.同时,发现缘板表面再结晶在叶片使用之前已存在,是缘板凝固区域因过大铸造热应力而形成碳化物,进而在热处理过程形成晶界富钨白色析出相的再结晶晶粒.
- DD6单晶 /
- 涡轮叶片 /
- 缘板裂纹 /
- 铸造热应力 /
- 再结晶
Abstract: It was found that the cracks appeared on the surface of DD6 single crystal turbine blade platform after testing.Based on the cracks character,the platform failure mode was studied by appearance check,observation on fracture surfaces,microscopic structure examination,and chemical analysis.The results show that the cracks have made from the surface recrystallization of DD6 single crystal turbine blade platform;it has relation to the grain boundary face.Under stress condition,the cracks have expensed along the white particles bond until fatigue failure.Meanwhile,it was found that the recrystallization zone already exists at its surface before application.Owing to the larger cast stress during cast process,the carbide is formatted in platform zone.Then,the recrystallization grain,which mass precipitated phases with W element are around its boundary,is formatted in heat treatment.
- DD6 single crystal /
- turbine blade /
- platform crack /
- cast heat-stress /
- recrystallization

HTML

参考文献(16)

[1]	张卫方,高威,赵爱国,等.定向凝固合金叶片的再结晶与疲劳失效[J].航空学报,2003,24(4):377-381. ZHANG Weifang,GAO Wei,ZHAO Aiguo,et al.Recrystallization and fatigue failure of blades made of a direction ally solidified alloy[J].Chinese Journal of Aeronautics,2003,24(4):377-381.(in Chinese)
[2]	Gell M,Duhl D N,Giamei A F.The development of single crystal super alloy turbine blade[J].Superalloys,1980,10:205-214.
[3]	Porter A,Ralph B.The recrystallization of Ni base superalloy[J].J.Mater Sci.,1981,16:707-710.
[4]	李鸿,卫广智.DZ4合金定向凝固涡轮叶片再结晶问题研究[J].贵州工业大学学报,2006,35(1):39-42. LI Hong,WEI Guangzhi.Study on DZ4 alloy directional coagulation turbine blade’s recrystallization[J].Jouranal of Guizhou University of Technology,2006,35(1):39-42.(in Chinese)
[5]	赵爱国,杨健.高压涡轮盘榫齿裂纹分析[J].机械强度,2006,28(4):624-627. ZHAO Aiguo,YANG Jian.Crack failures of tenons teeth in turbine disk[J].Journal of Mechanical Strength,2006,28(4):624-627.(in Chinese)
[6]	Brgel R,Portell A P D,Preuh S J.Recrystallization in single crystals of nickel base superalloys.Warren Dale,PA:TMS,2000:229-238.
[7]	王志刚,赵京晨,燕平,等.一种镍基单晶高温合金的再结晶[J].钢铁研究学报,2009,21(2):23-27. WANG Zhigang,ZHAO Jingchen,YAN Ping,et al.Recrystallization of nickel base single crystal superalloy[J].Journal of Iron and Steel Research,2009,21(2):23-27.(in Chinese)
[8]	Bond S D,Martin J W.Surface recrystallization in a single crystal Ni base superalloy[J].Journal of Materials Science,1984,19(12):3864-3872.
[9]	张兵,何玉怀,韩梅,等.单晶高温合金涡轮叶片榫齿裂纹原因分析[J].失效分析与预防,2010,5(1):60-64. ZHANG Bin,HE Yuhui,HAN Mei,et al.Crack failures of tenons teeth in single crystal turbine blades[J].Failire Analysis and Prevention,2010,5(1):60-64.(in Chinese)
[10]	陶春虎,张卫方,李运菊,等.定向凝固和单晶高温合金的再结晶[J].失效分析与预防,2006,1(1):1-7. TAO Chunhu,ZHANG Weifang,L I Yunju,et al.Recrysta llization of directionally solid if ied and single crystal superalloy[J].Failire Analysis and Prevention,2006,1(1):1-7.(in Chinese)
[11]	卫平,李嘉荣,钟振纲.一种镍基单晶高温合金的表面再结晶研究[J].材料工程,2001(10):5-8. WEI Ping,LI Jiarong,ZHONG Zhengang.Study on the surface recrystallization of Ni-based single crystal superalloy[J].Material Engineering,2001,10:5-8.(in Chinese)
[12]	贾波,李春光,李运菊,等.定向凝固高温合金DZ4的动态再结晶行为研究[J].航空材料学报,2009,29(1):43-46. JIA Bo,LI Chunguang,LI Yunju,et al.Research on dynamic recrystallization behavior of directionally solidified DZ4 superalloy[J].Journal of Aeronautical Materials,2009,29(1):43-46.(in Chinese)
[13]	Goldschmidt D,Pau L U,Sahm P R.Porosityclusters and recrystallization in single crystal components.Warren Dale,PA:TMS,1992:155-164.
[14]	张卫方,田继丰,刘高远,等.定向凝固合金叶片的裂纹与再结晶研究[J].机械强度,2003,25(6):671-674. ZHANG Weifang,TIAN Jifeng,LIU Gaoyuan,et al.recrystallization of blades made of a directionaly solidification alloy[J].Journal of Mechanical Strength,2003,25(6):671-674.(in Chinese)
[15]	Cox D C,Roebuck B,Rae C M F,et al.Recrystallization of single crystal superalloy CMSX-4[J].Materials Science and Technology,2003,19(4):440-446.
[16]	Wang D L,Jin T,Yang S Q,et al.Surface recrystallization and its effect on rupture life of SRR99 single crystal superalloy[J].Materials Science Forum,2007,(546-549):1229-1234.